[U-Boot] [PATCH 02/20] arm/km: use correct kw_gpio function for NAND/SPI switching

Holger Brunck holger.brunck at keymile.com
Tue Jun 12 10:38:00 CEST 2012


On 06/12/2012 06:39 AM, Prafulla Wadaskar wrote:
> 
> 
>> -----Original Message-----
>> From: Valentin Longchamp [mailto:valentin.longchamp at keymile.com]
>> Sent: 07 June 2012 15:37
>> To: prafulla at mavell.com
>> Cc: Valentin Longchamp; holger.brunck at keymile.com; u-
>> boot at lists.denx.de; Gerlando Falauto; Prafulla Wadaskar
>> Subject: [PATCH 02/20] arm/km: use correct kw_gpio function for
>> NAND/SPI switching
>>
>> This used to be done with registers direct access, which is not clear
>> and optimal.
>>
>> Signed-off-by: Valentin Longchamp <valentin.longchamp at keymile.com>
>> Signed-off-by: Holger Brunck <holger.brunck at keymile.com>
>> cc: Gerlando Falauto <gerlando.falauto at keymile.com>
>> cc: Prafulla Wadaskar <prafulla at marvell.com>
>> ---
>>  board/keymile/km_arm/km_arm.c |   53 +++++++++++++++++++++-----------
>> --------
>>  include/configs/km/km_arm.h   |    1 +
>>  2 files changed, 29 insertions(+), 25 deletions(-)
>>
>> diff --git a/board/keymile/km_arm/km_arm.c
>> b/board/keymile/km_arm/km_arm.c
>> index ed12b5c..e4ae1fb 100644
>> --- a/board/keymile/km_arm/km_arm.c
>> +++ b/board/keymile/km_arm/km_arm.c
>> @@ -247,15 +247,12 @@ int board_early_init_f(void)
>>  	kirkwood_mpp_conf(kwmpp_config, NULL);
>>
>>  	/*
>> -	 * The FLASH_GPIO_PIN switches between using a
>> +	 * The KM_FLASH_GPIO_PIN switches between using a
>>  	 * NAND or a SPI FLASH. Set this pin on start
>>  	 * to NAND mode.
>>  	 */
>> -	tmp = readl(KW_GPIO0_BASE);
>> -	writel(tmp | FLASH_GPIO_PIN , KW_GPIO0_BASE);
>> -	tmp = readl(KW_GPIO0_BASE + 4);
>> -	writel(tmp & (~FLASH_GPIO_PIN) , KW_GPIO0_BASE + 4);
>> -
>> +	kw_gpio_set_valid(KM_FLASH_GPIO_PIN, 1);
>> +	kw_gpio_direction_output(KM_FLASH_GPIO_PIN, 1);
>>  #if defined(CONFIG_SOFT_I2C)
>>  	/* init the GPIO for I2C Bitbang driver */
>>  	kw_gpio_set_valid(KM_KIRKWOOD_SDA_PIN, 1);
>> @@ -284,35 +281,41 @@ int board_init(void)
>>  	return 0;
>>  }
>>
>> +int km_hw_spi_bus_claim(int on)
>> +{
>> +	int gpio_value = !on;
>> +
>> +	if (on) {
>> +		kwmpp_config[0] = MPP0_SPI_SCn;
>> +		kwmpp_config[1] = MPP1_SPI_MOSI;
>> +		kwmpp_config[2] = MPP2_SPI_SCK;
>> +		kwmpp_config[3] = MPP3_SPI_MISO;
>> +	} else {
>> +		kwmpp_config[0] = MPP0_NF_IO2;
>> +		kwmpp_config[1] = MPP1_NF_IO3;
>> +		kwmpp_config[2] = MPP2_NF_IO4;
>> +		kwmpp_config[3] = MPP3_NF_IO5;
>> +	}
> 
> NACK...
> 

Could you please be a bit more verbose. Why do you NACK this? This code is only
related to our boards...

Regards
Holger




More information about the U-Boot mailing list