[U-Boot] [PATCH 08/11] u8500: Enabling power to MMC device on AB8500 V2
mathieu.poirier at linaro.org
mathieu.poirier at linaro.org
Mon Jun 18 18:35:41 CEST 2012
From: "Mathieu J. Poirier" <mathieu.poirier at linaro.org>
Register mapping has changed on power control chip between
the first and second revision.
Signed-off-by: Mathieu Poirier <mathieu.poirier at linaro.org>
Signed-off-by: John Rigby <john.rigby at linaro.org>
---
arch/arm/cpu/armv7/u8500/cpu.c | 89 ++++++++++++++++++++--------
arch/arm/include/asm/arch-u8500/hardware.h | 22 ++++++-
board/st-ericsson/snowball/snowball.c | 5 ++
3 files changed, 88 insertions(+), 28 deletions(-)
diff --git a/arch/arm/cpu/armv7/u8500/cpu.c b/arch/arm/cpu/armv7/u8500/cpu.c
index 593199c..02bb332 100644
--- a/arch/arm/cpu/armv7/u8500/cpu.c
+++ b/arch/arm/cpu/armv7/u8500/cpu.c
@@ -36,11 +36,19 @@
#define CPUID_DB8500V2 0x412fc091
#define ASICID_DB8500V11 0x008500A1
-static unsigned int read_asicid(void)
+static unsigned int read_asicid(void);
+
+static inline unsigned int read_cpuid(void)
{
- unsigned int *address = (void *)U8500_BOOTROM_BASE
- + U8500_BOOTROM_ASIC_ID_OFFSET;
- return readl(address);
+ unsigned int val;
+
+ /* Main ID register (MIDR) */
+ asm("mrc p15, 0, %0, c0, c0, 0"
+ : "=r" (val)
+ :
+ : "cc");
+
+ return val;
}
static int cpu_is_u8500v11(void)
@@ -53,6 +61,18 @@ static int cpu_is_u8500v2(void)
return read_cpuid() == CPUID_DB8500V2;
}
+static unsigned int read_asicid(void)
+{
+ unsigned int *address;
+
+ if (cpu_is_u8500v2())
+ address = (void *) U8500_ASIC_ID_LOC_V2;
+ else
+ address = (void *) U8500_ASIC_ID_LOC_ED_V1;
+
+ return readl(address);
+}
+
#ifdef CONFIG_ARCH_CPU_INIT
/*
* SOC specific cpu init
@@ -68,22 +88,22 @@ int arch_cpu_init(void)
#ifdef CONFIG_MMC
-#define LDO_VAUX3_MASK 0x3
-#define LDO_VAUX3_ENABLE 0x1
-#define VAUX3_VOLTAGE_2_9V 0xd
-
-#define AB8500_REGU_CTRL2 0x4
-#define AB8500_REGU_VRF1VAUX3_REGU_REG 0x040A
-#define AB8500_REGU_VRF1VAUX3_SEL_REG 0x0421
-
int u8500_mmc_power_init(void)
{
int ret;
- int val;
+ int enable, voltage;
+ int ab8500_revision;
- if (!cpu_is_u8500v11())
+ if (!cpu_is_u8500v11() && !cpu_is_u8500v2())
return 0;
+ /* Get AB8500 revision */
+ ret = ab8500_read(AB8500_MISC, AB8500_REV_REG);
+ if (ret < 0)
+ goto out;
+
+ ab8500_revision = ret;
+
/*
* On v1.1 HREF boards (HREF+), Vaux3 needs to be enabled for the SD
* card to work. This is done by enabling the regulators in the AB8500
@@ -95,33 +115,50 @@ int u8500_mmc_power_init(void)
* Turn off and delay is required to have it work across soft reboots.
*/
- ret = prcmu_i2c_read(AB8500_REGU_CTRL2, AB8500_REGU_VRF1VAUX3_REGU_REG);
+ /* Turn off (read-modify-write) */
+ ret = ab8500_read(AB8500_REGU_CTRL2,
+ AB8500_REGU_VRF1VAUX3_REGU_REG);
if (ret < 0)
goto out;
- val = ret;
+ enable = ret;
/* Turn off */
- ret = prcmu_i2c_write(AB8500_REGU_CTRL2, AB8500_REGU_VRF1VAUX3_REGU_REG,
- val & ~LDO_VAUX3_MASK);
+ ret = ab8500_write(AB8500_REGU_CTRL2,
+ AB8500_REGU_VRF1VAUX3_REGU_REG,
+ enable & ~LDO_VAUX3_ENABLE_MASK);
if (ret < 0)
goto out;
udelay(10 * 1000);
- /* Set the voltage to 2.9V */
- ret = prcmu_i2c_write(AB8500_REGU_CTRL2,
- AB8500_REGU_VRF1VAUX3_SEL_REG,
- VAUX3_VOLTAGE_2_9V);
+ /* Set the voltage to 2.91 V or 2.9 V without overriding VRF1 value */
+ ret = ab8500_read(AB8500_REGU_CTRL2,
+ AB8500_REGU_VRF1VAUX3_SEL_REG);
if (ret < 0)
goto out;
- val = val & ~LDO_VAUX3_MASK;
- val = val | LDO_VAUX3_ENABLE;
+ voltage = ret;
+
+ if (ab8500_revision < 0x20) {
+ voltage &= ~LDO_VAUX3_SEL_MASK;
+ voltage |= LDO_VAUX3_SEL_2V9;
+ } else {
+ voltage &= ~LDO_VAUX3_V2_SEL_MASK;
+ voltage |= LDO_VAUX3_V2_SEL_2V91;
+ }
+
+ ret = ab8500_write(AB8500_REGU_CTRL2,
+ AB8500_REGU_VRF1VAUX3_SEL_REG, voltage);
+ if (ret < 0)
+ goto out;
/* Turn on the supply */
- ret = prcmu_i2c_write(AB8500_REGU_CTRL2,
- AB8500_REGU_VRF1VAUX3_REGU_REG, val);
+ enable &= ~LDO_VAUX3_ENABLE_MASK;
+ enable |= LDO_VAUX3_ENABLE_VAL;
+
+ ret = ab8500_write(AB8500_REGU_CTRL2,
+ AB8500_REGU_VRF1VAUX3_REGU_REG, enable);
out:
return ret;
diff --git a/arch/arm/include/asm/arch-u8500/hardware.h b/arch/arm/include/asm/arch-u8500/hardware.h
index 8044ac3..ee03419 100644
--- a/arch/arm/include/asm/arch-u8500/hardware.h
+++ b/arch/arm/include/asm/arch-u8500/hardware.h
@@ -77,11 +77,21 @@
#define U8500_CLKRST1_BASE (U8500_PER1_BASE + 0xf000)
/* Last page of Boot ROM */
-#define U8500_BOOTROM_BASE 0x9001f000
-#define U8500_BOOTROM_ASIC_ID_OFFSET 0x0ff4
+#define U8500_BOOTROM_BASE 0x90000000
+#define U8500_ASIC_ID_LOC_ED_V1 (U8500_BOOTROM_BASE + 0x1FFF4)
+#define U8500_ASIC_ID_LOC_V2 (U8500_BOOTROM_BASE + 0x1DBF4)
/* AB8500 specifics */
+
+/* address bank */
+#define AB8500_REGU_CTRL2 0x0004
#define AB8500_MISC 0x0010
+
+/* registers */
+#define AB8500_REGU_VRF1VAUX3_REGU_REG 0x040A
+#define AB8500_REGU_VRF1VAUX3_SEL_REG 0x0421
+#define AB8500_REV_REG 0x1080
+
#define AB8500_GPIO_SEL2_REG 0x1001
#define AB8500_GPIO_DIR2_REG 0x1011
#define AB8500_GPIO_DIR4_REG 0x1013
@@ -89,4 +99,12 @@
#define AB8500_GPIO_OUT2_REG 0x1021
#define AB8500_GPIO_OUT4_REG 0x1023
+#define LDO_VAUX3_ENABLE_MASK 0x3
+#define LDO_VAUX3_ENABLE_VAL 0x1
+#define LDO_VAUX3_SEL_MASK 0xf
+#define LDO_VAUX3_SEL_2V9 0xd
+#define LDO_VAUX3_V2_SEL_MASK 0x7
+#define LDO_VAUX3_V2_SEL_2V91 0x7
+
+
#endif /* __ASM_ARCH_HARDWARE_H */
diff --git a/board/st-ericsson/snowball/snowball.c b/board/st-ericsson/snowball/snowball.c
index bc95c50..2c01bc1 100644
--- a/board/st-ericsson/snowball/snowball.c
+++ b/board/st-ericsson/snowball/snowball.c
@@ -27,6 +27,7 @@
#include <asm/arch/db8500_pincfg.h>
#include <asm/arch/prcmu.h>
#include <asm/arch/hardware.h>
+#include <asm/arch/sys_proto.h>
#include "db8500_pins.h"
@@ -268,5 +269,9 @@ int board_late_init(void)
if ((raise_ab8500_gpio16() < 0))
printf("error: cant' raise GPIO16\n");
+#ifdef CONFIG_MMC
+ u8500_mmc_power_init();
+#endif /* CONFIG_MMC */
+
return 0;
}
--
1.7.5.4
More information about the U-Boot
mailing list