[U-Boot] [GIT PULL] Update - Pull request: u-boot-imx

[Stefano Babic]

Hi Albert,

please pull from u-boot-imx (rebased on current u-boot-arm).

The following changes since commit cd207cde948ecf9ff50a0fa1ae2650f65579c9c9:

  IXP: Fix GPIO_INT_ACT_LOW_SET() (2012-03-26 23:09:26 +0200)

are available in the git repository at:
  git://www.denx.de/git/u-boot-imx.git master

Dirk Behme (1):
      imximage: Remove overwriting of flash_offset

Eric Nelson (4):
      i.MX6: mx6qsabrelite: add ext2 support
      mx6q: mx6qsabrelite: setup_spi() should be called in board_init to
allow use for environment
      i.MX6: mx6q_sabrelite: add CONFIG_REVISION_TAG
      i.MX6: mx6qsabrelite: add MACH_TYPE_MX6Q_SABRELITE

Fabio Estevam (15):
      mx51evk: Fix CONFIG_SYS_MEMTEST_END
      mx53evk: Fix CONFIG_SYS_MEMTEST_END
      mx53smd: Fix CONFIG_SYS_MEMTEST_END
      efikamx: Fix CONFIG_SYS_MEMTEST_END
      mx31pdk: Fix CONFIG_SYS_MEMTEST_END
      mx6: Fix reset cause for Power On Reset case
      mx6: Remove duplicate definition of ANATOP_BASE_ADDR
      pmic_i2c: Return error in case of invalid pmic_i2c_tx_num
      mxs_spi: Return proper timeout error
      mx6: Read silicon revision from register
      USB: ehci-mx6: Add proper IO accessors
      mx28evk: Provide default values for SPI bus and chip select
      configs: imx: Use CONFIG_SF_DEFAULT_CS
      mx53: Make PLL2 to be the parent of UART clock
      mx53ard: Initialize return code with error

Helmut Raiger (1):
      mx31: add "ARM11P power gating" to get_reset_cause

Marek Vasut (3):
      i.MX28: Enable additional DRAM address bits
      i.MX28: Make the stabilization delays shorter
      i.MX28: Drop __naked function from spl_mem_init

 arch/arm/cpu/arm1136/mx31/generic.c           |    2 +
 arch/arm/cpu/arm926ejs/mx28/spl_mem_init.c    |   12 +--
 arch/arm/cpu/arm926ejs/mx28/spl_power_init.c  |    8 +-
 arch/arm/cpu/armv7/imx-common/cpu.c           |   25 ++++-
 arch/arm/cpu/armv7/mx5/lowlevel_init.S        |   20 +++-
 arch/arm/cpu/armv7/mx6/soc.c                  |    8 ++-
 arch/arm/include/asm/arch-mx6/imx-regs.h      |  143
++++++++++++++++++++++++-
 board/freescale/mx53ard/mx53ard.c             |    2 +-
 board/freescale/mx6qsabrelite/mx6qsabrelite.c |   13 ++-
 drivers/misc/pmic_i2c.c                       |    6 +
 drivers/spi/mxs_spi.c                         |    6 +-
 drivers/usb/host/ehci-mx6.c                   |   13 +--
 include/configs/efikamx.h                     |    4 +-
 include/configs/m28evk.h                      |    2 +-
 include/configs/mx28evk.h                     |    2 +
 include/configs/mx31pdk.h                     |    2 +-
 include/configs/mx51evk.h                     |    2 +-
 include/configs/mx53evk.h                     |    2 +-
 include/configs/mx53smd.h                     |    2 +-
 include/configs/mx6qsabrelite.h               |    4 +
 include/configs/vision2.h                     |    2 +-
 tools/imximage.c                              |   18 +++-
 tools/imximage.h                              |    1 +
 23 files changed, 251 insertions(+), 48 deletions(-)

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================