[U-Boot] [PATCH V5] i.MX6: mx6q_sabrelite: add SATA bindings

Eric Nelson eric.nelson at boundarydevices.com
Tue May 1 21:55:11 CEST 2012


Signed-off-by: Eric Nelson <eric.nelson at boundarydevices.com>
---
V2 has been stripped of the board-independent changes and
uses clrsetbits_le32() instead of twiddling bits by hand.

V3 returns immediately from setup_sata() if enable_sata_clock()
returns an error.

V4 removes extra #include and addresses a style issue as discussed
on the ML.

V5 addresses another (hopefully last) style issue.

 board/freescale/mx6qsabrelite/mx6qsabrelite.c |   31 +++++++++++++++++++++++++
 include/configs/mx6qsabrelite.h               |   13 ++++++++++
 2 files changed, 44 insertions(+), 0 deletions(-)

diff --git a/board/freescale/mx6qsabrelite/mx6qsabrelite.c b/board/freescale/mx6qsabrelite/mx6qsabrelite.c
index 1d09a72..cdd2f15 100644
--- a/board/freescale/mx6qsabrelite/mx6qsabrelite.c
+++ b/board/freescale/mx6qsabrelite/mx6qsabrelite.c
@@ -25,6 +25,7 @@
 #include <asm/arch/imx-regs.h>
 #include <asm/arch/mx6x_pins.h>
 #include <asm/arch/iomux-v3.h>
+#include <asm/arch/clock.h>
 #include <asm/errno.h>
 #include <asm/gpio.h>
 #include <mmc.h>
@@ -267,6 +268,32 @@ int board_eth_init(bd_t *bis)
 	return 0;
 }
 
+#ifdef CONFIG_CMD_SATA
+
+int setup_sata(void)
+{
+	struct iomuxc_base_regs *const iomuxc_regs
+		= (struct iomuxc_base_regs *) IOMUXC_BASE_ADDR;
+	int ret = enable_sata_clock();
+	if (ret)
+		return ret;
+
+	clrsetbits_le32(&iomuxc_regs->gpr[13],
+			IOMUXC_GPR13_SATA_MASK,
+			IOMUXC_GPR13_SATA_PHY_8_RXEQ_3P0DB
+			|IOMUXC_GPR13_SATA_PHY_7_SATA2M
+			|IOMUXC_GPR13_SATA_SPEED_3G
+			|(3<<IOMUXC_GPR13_SATA_PHY_6_SHIFT)
+			|IOMUXC_GPR13_SATA_SATA_PHY_5_SS_DISABLED
+			|IOMUXC_GPR13_SATA_SATA_PHY_4_ATTEN_9_16
+			|IOMUXC_GPR13_SATA_PHY_3_TXBOOST_0P00_DB
+			|IOMUXC_GPR13_SATA_PHY_2_TX_1P104V
+			|IOMUXC_GPR13_SATA_PHY_1_SLOW);
+
+	return 0;
+}
+#endif
+
 int board_early_init_f(void)
 {
        setup_iomux_uart();
@@ -283,6 +310,10 @@ int board_init(void)
 	setup_spi();
 #endif
 
+#ifdef CONFIG_CMD_SATA
+	setup_sata();
+#endif
+
        return 0;
 }
 
diff --git a/include/configs/mx6qsabrelite.h b/include/configs/mx6qsabrelite.h
index f52c3c7..1d92dd0 100644
--- a/include/configs/mx6qsabrelite.h
+++ b/include/configs/mx6qsabrelite.h
@@ -71,6 +71,19 @@
 #define CONFIG_CMD_FAT
 #define CONFIG_DOS_PARTITION
 
+#define CONFIG_CMD_SATA
+/*
+ * SATA Configs
+ */
+#ifdef CONFIG_CMD_SATA
+#define CONFIG_DWC_AHSATA
+#define CONFIG_SYS_SATA_MAX_DEVICE	1
+#define CONFIG_DWC_AHSATA_PORT_ID	0
+#define CONFIG_DWC_AHSATA_BASE_ADDR	SATA_ARB_BASE_ADDR
+#define CONFIG_LBA48
+#define CONFIG_LIBATA
+#endif
+
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_MII
-- 
1.7.9



More information about the U-Boot mailing list