[U-Boot] [PATCH V3 4/9] EXYNOS5: DWMMC: Added FDT support for DWMMC
Amarendra Reddy
amar.lavanuru at gmail.com
Thu Jan 3 05:32:55 CET 2013
Hi Jaehoon,
Thanks for the comments.
Please find my response below.
Thanks & Regards
Amarendra
On 2 January 2013 10:50, Jaehoon Chung <jh80.chung at samsung.com> wrote:
> On 12/31/2012 07:58 PM, Amar wrote:
> > This patch adds FDT support for DWMMC, by reading the DWMMC node data
> > from the device tree and initialising DWMMC channels as per data
> > obtained from the node.
> >
> > Changes from V1:
> > 1)Updated code to have same signature for the function
> > exynos_dwmci_init() for both FDT and non-FDT versions.
> > 2)Updated code to pass device_id parameter to the function
> > exynos5_mmc_set_clk_div() instead of index.
> > 3)Updated code to decode the value of "samsung,width" from FDT.
> > 4)Channel index is computed instead of getting from FDT.
> >
> > Changes from V2:
> > 1)Updation of commit message and resubmition of proper patch set.
> >
> > Signed-off-by: Vivek Gautam <gautam.vivek at samsung.com>
> > Signed-off-by: Amar <amarendra.xt at samsung.com>
> > ---
> > arch/arm/include/asm/arch-exynos/dwmmc.h | 4 ++
> > drivers/mmc/exynos_dw_mmc.c | 116
> +++++++++++++++++++++++++++++--
> > include/dwmmc.h | 4 ++
> > 3 files changed, 117 insertions(+), 7 deletions(-)
> >
> > diff --git a/arch/arm/include/asm/arch-exynos/dwmmc.h
> b/arch/arm/include/asm/arch-exynos/dwmmc.h
> > index 8acdf9b..40dcc7b 100644
> > --- a/arch/arm/include/asm/arch-exynos/dwmmc.h
> > +++ b/arch/arm/include/asm/arch-exynos/dwmmc.h
> > @@ -29,8 +29,12 @@
> >
> > int exynos_dwmci_init(u32 regbase, int bus_width, int index);
> >
> > +#ifdef CONFIG_OF_CONTROL
> > +unsigned int exynos_dwmmc_init(const void *blob);
> > +#else
> > static inline unsigned int exynos_dwmmc_init(int index, int bus_width)
> > {
> > unsigned int base = samsung_get_base_mmc() + (0x10000 * index);
> > return exynos_dwmci_init(base, bus_width, index);
> > }
> > +#endif
> > diff --git a/drivers/mmc/exynos_dw_mmc.c b/drivers/mmc/exynos_dw_mmc.c
> > index 72a31b7..541889f 100644
> > --- a/drivers/mmc/exynos_dw_mmc.c
> > +++ b/drivers/mmc/exynos_dw_mmc.c
> > @@ -19,39 +19,141 @@
> > */
> >
> > #include <common.h>
> > -#include <malloc.h>
> > #include <dwmmc.h>
> > +#include <fdtdec.h>
> > +#include <libfdt.h>
> > +#include <malloc.h>
> > #include <asm/arch/dwmmc.h>
> > #include <asm/arch/clk.h>
> > +#include <asm/arch/pinmux.h>
> > +
> > +#define DWMMC_MAX_CH_NUM 4
> > +#define DWMMC_MAX_FREQ 52000000
> > +#define DWMMC_MIN_FREQ 400000
> > +#define DWMMC_MMC0_CLKSEL_VAL 0x03030001
> > +#define DWMMC_MMC2_CLKSEL_VAL 0x03020001
> >
> > static char *EXYNOS_NAME = "EXYNOS DWMMC";
> > +u32 timing[3];
> >
> > +/*
> > + * Function used as callback function to initialise the
> > + * CLKSEL register for every mmc channel.
> > + */
> > static void exynos_dwmci_clksel(struct dwmci_host *host)
> > {
> > - u32 val;
> > - val = DWMCI_SET_SAMPLE_CLK(DWMCI_SHIFT_0) |
> > - DWMCI_SET_DRV_CLK(DWMCI_SHIFT_0) | DWMCI_SET_DIV_RATIO(0);
> > + dwmci_writel(host, DWMCI_CLKSEL, host->clksel_val);
> > +}
> >
> > - dwmci_writel(host, DWMCI_CLKSEL, val);
> > +unsigned int exynos_dwmci_get_clk(int dev_index)
> > +{
> > + return get_mmc_clk(dev_index);
> > }
> >
> > int exynos_dwmci_init(u32 regbase, int bus_width, int index)
> > {
> > struct dwmci_host *host = NULL;
> > + int dev_id = 0;
> > host = malloc(sizeof(struct dwmci_host));
> > if (!host) {
> > printf("dwmci_host malloc fail!\n");
> > return 1;
> > }
> > + /* Convert index into corresponding peripheral ID */
> > + dev_id = index + PERIPH_ID_SDMMC0;
> Is it right at every case?
>
Yes, it is right in every case.
Consider the finction "int exynos_dwmci_init(u32 regbase, int bus_width,
int index)"
If the input argument 'index' is between (0-3), then the statement "dev_id
= index + PERIPH_ID_SDMMC0;" works good.
So, the function exynos_dwmci_init(u32 regbase, int bus_width, int index)
is being called as below
1) FDT Case:
The function exynos_dwmmc_init() calls exynos_dwmmc_init()
The dev_id is extracted from arch/arm/dts/exynos5250.dtsi. The dev_id is
nothing but the interrupt number.
dwmmc0 - dev_id = 75
dwmmc1 - dev_id = 76
dwmmc2 - dev_id = 77
dwmmc3 - dev_id = 78
At same time the enum values are (Refer
"arch/arm/include/asm/arch-exynos/periph.h")
PERIPH_ID_SDMMC0 = 75,
PERIPH_ID_SDMMC1,
PERIPH_ID_SDMMC2,
PERIPH_ID_SDMMC3,
Here "index = dev_id - PERIPH_ID_SDMMC0" works good for all channels
(mmc0 - mmc3)
As proper values are mentioned in arch/arm/dts/exynos5250.dtsi, proper
values of "index" (i.e 0 - 3) will be computed here.
2) Non-FDT case:
The function board_mmc_init() calls exynos_dwmmc_init() as shown below
int board_mmc_init(bd_t *bis)
{
....
....
/*EMMC: dwmmc Channel-0 with 8 bit bus width */
err = exynos_dwmmc_init(0, 8);
}
Here the coder shall ensure to pass proper index number (0 to 3) for porper
working.
> > +
> > + /* set the clock divisor - clk_div_fsys for mmc */
> > + if (exynos5_mmc_set_clk_div(dev_id)) {
> > + debug("mmc clock div set failed\n");
> > + return -1;
> > + }
> >
> > host->name = EXYNOS_NAME;
> > host->ioaddr = (void *)regbase;
> > host->buswidth = bus_width;
> > +#ifdef CONFIG_OF_CONTROL
> > + host->clksel_val = (DWMCI_SET_SAMPLE_CLK(timing[0]) |
> > + DWMCI_SET_DRV_CLK(timing[1]) |
> > + DWMCI_SET_DIV_RATIO(timing[2]));
> > +#else
> > + if (0 == index)
> > + host->clksel_val = DWMMC_MMC0_CLKSEL_VAL;
> > + if (2 == index)
> > + host->clksel_val = DWMMC_MMC2_CLKSEL_VAL;
> > +#endif
> > host->clksel = exynos_dwmci_clksel;
> > host->dev_index = index;
> > -
> > - add_dwmci(host, 52000000, 400000);
> > + host->mmc_clk = exynos_dwmci_get_clk;
> > + /* Add the mmc chennel to be registered with mmc core */
> > + add_dwmci(host, DWMMC_MAX_FREQ, DWMMC_MIN_FREQ);
> >
> > return 0;
> > }
> >
> > +#ifdef CONFIG_OF_CONTROL
> > +unsigned int exynos_dwmmc_init(const void *blob)
> > +{
> > + u32 base;
> > + int index, bus_width;
> > + int node_list[DWMMC_MAX_CH_NUM];
> > + int err = 0;
> > + int dev_id, flag;
> > + int count, i;
> > +
> > + count = fdtdec_find_aliases_for_id(blob, "dwmmc",
> > + COMPAT_SAMSUNG_EXYNOS5_DWMMC, node_list,
> > + DWMMC_MAX_CH_NUM);
> > +
> > + for (i = 0; i < count; i++) {
> > + int node = node_list[i];
> > +
> > + if (node <= 0)
> > + continue;
> > +
> > + /* Extract device id for each mmc channel */
> > + dev_id = pinmux_decode_periph_id(blob, node);
> > +
> > + /* Get the bus width from the device node */
> > + bus_width = fdtdec_get_int(blob, node,
> "samsung,bus-width", 0);
> > + if (bus_width < 0) {
> > + debug("DWMMC: Can't get bus-width\n");
> > + return -1;
> > + }
> > + if (8 == bus_width)
> > + flag = PINMUX_FLAG_8BIT_MODE;
> > + else
> > + flag = PINMUX_FLAG_NONE;
> > +
> > + /* config pinmux for each mmc channel */
> > + err = exynos_pinmux_config(dev_id, flag);
> > + if (err) {
> > + debug("DWMMC not configured\n");
> > + return err;
> > + }
> > +
> > + index = dev_id - PERIPH_ID_SDMMC0;
> > +
> > + /* Get the base address from the device node */
> > + base = fdtdec_get_addr(blob, node, "reg");
> > + if (!base) {
> > + debug("DWMMC: Can't get base address\n");
> > + return -1;
> > + }
> > + /* Extract the timing info from the node */
> > + err = fdtdec_get_int_array(blob, node, "samsung,timing",
> > + timing, 3);
> > + if (err) {
> > + debug("Can't get sdr-timings for divider\n");
> > + return -1;
> > + }
> > + /* Initialise each mmc channel */
> > + err = exynos_dwmci_init(base, bus_width, index);
> > + if (err) {
> > + debug("Can't do dwmci init\n");
> > + return -1;
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +#endif
> > diff --git a/include/dwmmc.h b/include/dwmmc.h
> > index c8b1d40..4a42849 100644
> > --- a/include/dwmmc.h
> > +++ b/include/dwmmc.h
> > @@ -123,6 +123,9 @@
> > #define MSIZE(x) ((x) << 28)
> > #define RX_WMARK(x) ((x) << 16)
> > #define TX_WMARK(x) (x)
> > +#define RX_WMARK_SHIFT 16
> > +#define RX_WMARK_MASK (0xfff << RX_WMARK_SHIFT)
> > +
> >
> > #define DWMCI_IDMAC_OWN (1 << 31)
> > #define DWMCI_IDMAC_CH (1 << 4)
> > @@ -144,6 +147,7 @@ struct dwmci_host {
> > unsigned int bus_hz;
> > int dev_index;
> > int buswidth;
> > + u32 clksel_val;
> > u32 fifoth_val;
> > struct mmc *mmc;
> >
> >
>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>
More information about the U-Boot
mailing list