[U-Boot] [PATCH V4 6/9] SMDK5250: Initialise and Enable DWMMC, support FDT and non-FDT
Simon Glass
sjg at chromium.org
Thu Jan 10 17:57:05 CET 2013
Hi Amar,
On Fri, Jan 4, 2013 at 1:34 AM, Amar <amarendra.xt at samsung.com> wrote:
> This patch enables and initialises DWMMC for SMDK5250.
> Supports both FDT and non-FDT. This patch creates a new file
> 'exynos5-dt.c' meant for FDT support.
> exynos5-dt.c: This file shall contain all code which supports FDT.
> Any addition of FDT support for any module needs to be
> added in this file.
> smdk5250.c: This file shall contain the code which supports non-FDT.
> version. Any addition of non-FDT support for any module
> needs to be added in this file.
> May be, the file smdk5250.c can be removed in near future
> when non-FDT is not required.
>
> The Makefile is updated to compile only one of the files
> exynos5-dt.c / smdk5250.c based on FDT configuration.
>
> NOTE:
> Please note that all additions corresponding to FDT need to be added into the
> file exynos5-dt.c.
> At same time if non-FDT support is required then add the corresponding
> updations into smdk5250.c.
>
> Changes from V1:
> 1)A new file 'exynos5-dt.c' is created meant for FDT support
> 2)Makefile is updated to compile only one of the files
> exynos5-dt.c / smdk5250.c based on FDT configuration
>
> Changes from V2:
> 1)Updation of commit message and resubmition of proper patch set.
>
> Changes from V3:
> No change.
>
> Signed-off-by: Amar <amarendra.xt at samsung.com>
> ---
> board/samsung/smdk5250/Makefile | 4 +
> board/samsung/smdk5250/exynos5-dt.c | 242 ++++++++++++++++++++++++++++++++++++
> board/samsung/smdk5250/smdk5250.c | 97 +++++++--------
> include/configs/exynos5250-dt.h | 2 +
> include/i2c.h | 2 +
> 5 files changed, 292 insertions(+), 55 deletions(-)
> create mode 100644 board/samsung/smdk5250/exynos5-dt.c
>
> diff --git a/board/samsung/smdk5250/Makefile b/board/samsung/smdk5250/Makefile
> index 47c6a5a..ecca9f3 100644
> --- a/board/samsung/smdk5250/Makefile
> +++ b/board/samsung/smdk5250/Makefile
> @@ -32,8 +32,12 @@ COBJS += tzpc_init.o
> COBJS += smdk5250_spl.o
>
> ifndef CONFIG_SPL_BUILD
> +ifdef CONFIG_OF_CONTROL
> +COBJS += exynos5-dt.o
> +else
> COBJS += smdk5250.o
> endif
> +endif
>
> ifdef CONFIG_SPL_BUILD
> COBJS += spl_boot.o
> diff --git a/board/samsung/smdk5250/exynos5-dt.c b/board/samsung/smdk5250/exynos5-dt.c
> new file mode 100644
> index 0000000..da539ca
> --- /dev/null
> +++ b/board/samsung/smdk5250/exynos5-dt.c
> @@ -0,0 +1,242 @@
> +/*
> + * Copyright (C) 2012 Samsung Electronics
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#include <common.h>
> +#include <fdtdec.h>
> +#include <asm/io.h>
> +#include <i2c.h>
> +#include <netdev.h>
> +#include <spi.h>
> +#include <asm/arch/cpu.h>
> +#include <asm/arch/dwmmc.h>
> +#include <asm/arch/gpio.h>
> +#include <asm/arch/mmc.h>
> +#include <asm/arch/pinmux.h>
> +#include <asm/arch/sromc.h>
> +#include <power/pmic.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +int board_init(void)
> +{
> + gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
> +#ifdef CONFIG_EXYNOS_SPI
> + spi_init();
> +#endif
> + return 0;
> +}
> +
> +int dram_init(void)
> +{
> + gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE)
> + + get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE)
> + + get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE)
> + + get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE)
> + + get_ram_size((long *)PHYS_SDRAM_5, PHYS_SDRAM_7_SIZE)
> + + get_ram_size((long *)PHYS_SDRAM_6, PHYS_SDRAM_7_SIZE)
> + + get_ram_size((long *)PHYS_SDRAM_7, PHYS_SDRAM_7_SIZE)
> + + get_ram_size((long *)PHYS_SDRAM_8, PHYS_SDRAM_8_SIZE);
This looks ugly - is there any other way of doing this? Also 7 appears
in more than one line.
Since the banks are all SDRAM_BANK_SIZE apart, perhaps you could just
use a for loop with a single base address?
If this function is common with the other file then perhaps it should
go in a common file?
> + return 0;
> +}
> +
> +#if defined(CONFIG_POWER)
> +int power_init_board(void)
> +{
> + if (pmic_init(I2C_PMIC))
debug()
> + return -1;
> + else
> + return 0;
> +}
> +#endif
> +
> +void dram_init_banksize(void)
> +{
> + gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
> + gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1,
> + PHYS_SDRAM_1_SIZE);
> + gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
> + gd->bd->bi_dram[1].size = get_ram_size((long *)PHYS_SDRAM_2,
> + PHYS_SDRAM_2_SIZE);
> + gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
> + gd->bd->bi_dram[2].size = get_ram_size((long *)PHYS_SDRAM_3,
> + PHYS_SDRAM_3_SIZE);
> + gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
> + gd->bd->bi_dram[3].size = get_ram_size((long *)PHYS_SDRAM_4,
> + PHYS_SDRAM_4_SIZE);
> + gd->bd->bi_dram[4].start = PHYS_SDRAM_5;
> + gd->bd->bi_dram[4].size = get_ram_size((long *)PHYS_SDRAM_5,
> + PHYS_SDRAM_5_SIZE);
> + gd->bd->bi_dram[5].start = PHYS_SDRAM_6;
> + gd->bd->bi_dram[5].size = get_ram_size((long *)PHYS_SDRAM_6,
> + PHYS_SDRAM_6_SIZE);
> + gd->bd->bi_dram[6].start = PHYS_SDRAM_7;
> + gd->bd->bi_dram[6].size = get_ram_size((long *)PHYS_SDRAM_7,
> + PHYS_SDRAM_7_SIZE);
> + gd->bd->bi_dram[7].start = PHYS_SDRAM_8;
> + gd->bd->bi_dram[7].size = get_ram_size((long *)PHYS_SDRAM_8,
> + PHYS_SDRAM_8_SIZE);
and here
> +}
> +
> +static int decode_sromc(const void *blob, struct fdt_sromc *config)
> +{
> + int err;
> + int node;
> +
> + node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_SROMC);
> + if (node < 0) {
> + debug("Could not find SROMC node\n");
> + return node;
> + }
> +
> + config->bank = fdtdec_get_int(blob, node, "bank", 0);
> + config->width = fdtdec_get_int(blob, node, "width", 2);
> +
> + err = fdtdec_get_int_array(blob, node, "srom-timing", config->timing,
> + FDT_SROM_TIMING_COUNT);
> + if (err < 0) {
> + debug("Could not decode SROMC configuration\n");
Suggest:
debug("Could not decode SROMC configuration: %s\n", fdt_strerror(err));
> + return -FDT_ERR_NOTFOUND;
return err? Or the caller might just want -1
> + }
> +
> + return 0;
> +}
> +
> +int board_eth_init(bd_t *bis)
> +{
> +#ifdef CONFIG_SMC911X
> + u32 smc_bw_conf, smc_bc_conf;
> + struct fdt_sromc config;
> + fdt_addr_t base_addr;
> + int node;
> +
> + node = decode_sromc(gd->fdt_blob, &config);
> + if (node < 0) {
> + debug("%s: Could not find sromc configuration\n", __func__);
> + return 0;
> + }
> + node = fdtdec_next_compatible(gd->fdt_blob, node, COMPAT_SMSC_LAN9215);
> + if (node < 0) {
> + debug("%s: Could not find lan9215 configuration\n", __func__);
> + return 0;
> + }
> +
> + /* We now have a node, so any problems from now on are errors */
> + base_addr = fdtdec_get_addr(gd->fdt_blob, node, "reg");
> + if (base_addr == FDT_ADDR_T_NONE) {
> + debug("%s: Could not find lan9215 address\n", __func__);
> + return -1;
> + }
> +
> + /* Ethernet needs data bus width of 16 bits */
> + if (config.width != 2) {
> + debug("%s: Unsupported bus width %d\n", __func__,
> + config.width);
> + return -1;
> + }
> + smc_bw_conf = SROMC_DATA16_WIDTH(config.bank)
> + | SROMC_BYTE_ENABLE(config.bank);
> +
> + smc_bc_conf = SROMC_BC_TACS(config.timing[FDT_SROM_TACS]) |\
Can you remove the \ from each line?
> + SROMC_BC_TCOS(config.timing[FDT_SROM_TCOS]) |\
> + SROMC_BC_TACC(config.timing[FDT_SROM_TACC]) |\
> + SROMC_BC_TCOH(config.timing[FDT_SROM_TCOH]) |\
> + SROMC_BC_TAH(config.timing[FDT_SROM_TAH]) |\
> + SROMC_BC_TACP(config.timing[FDT_SROM_TACP]) |\
> + SROMC_BC_PMC(config.timing[FDT_SROM_PMC]);
> +
> + /* Select and configure the SROMC bank */
> + exynos_pinmux_config(PERIPH_ID_SROMC, config.bank);
> + s5p_config_sromc(config.bank, smc_bw_conf, smc_bc_conf);
> + return smc911x_initialize(0, base_addr);
> +#endif
> + return 0;
> +}
> +
> +#ifdef CONFIG_DISPLAY_BOARDINFO
> +int checkboard(void)
> +{
> + printf("\nBoard: SMDK5250\n");
> +
> + return 0;
> +}
> +#endif
> +
> +#ifdef CONFIG_GENERIC_MMC
> +int board_mmc_init(bd_t *bis)
> +{
> + int ret = 0;
Remove =0
> +
> + /* dwmmc initializattion for available channels */
> + ret = exynos_dwmmc_init(gd->fdt_blob);
> + if (ret)
> + debug("dwmmc init failed\n");
> +
> + return ret;
> +}
> +#endif
> +
> +static int board_uart_init(void)
> +{
> + int err;
> +
> + err = exynos_pinmux_config(PERIPH_ID_UART0, PINMUX_FLAG_NONE);
> + if (err) {
> + debug("UART0 not configured\n");
> + return err;
> + }
> +
> + err = exynos_pinmux_config(PERIPH_ID_UART1, PINMUX_FLAG_NONE);
> + if (err) {
> + debug("UART1 not configured\n");
> + return err;
> + }
> +
> + err = exynos_pinmux_config(PERIPH_ID_UART2, PINMUX_FLAG_NONE);
> + if (err) {
> + debug("UART2 not configured\n");
> + return err;
> + }
> +
> + err = exynos_pinmux_config(PERIPH_ID_UART3, PINMUX_FLAG_NONE);
> + if (err) {
> + debug("UART3 not configured\n");
> + return err;
> + }
Loop for this?
> +
> + return 0;
> +}
> +
> +#ifdef CONFIG_BOARD_EARLY_INIT_F
> +int board_early_init_f(void)
> +{
> + int err;
blank line
> + err = board_uart_init();
> + if (err) {
> + debug("UART init failed\n");
> + return err;
> + }
> +#ifdef CONFIG_SYS_I2C_INIT_BOARD
> + board_i2c_init(gd->fdt_blob);
> +#endif
> + return err;
> +}
> +#endif
> diff --git a/board/samsung/smdk5250/smdk5250.c b/board/samsung/smdk5250/smdk5250.c
> index 73c3ec0..e0fec11 100644
> --- a/board/samsung/smdk5250/smdk5250.c
> +++ b/board/samsung/smdk5250/smdk5250.c
> @@ -27,6 +27,7 @@
> #include <netdev.h>
> #include <spi.h>
> #include <asm/arch/cpu.h>
> +#include <asm/arch/dwmmc.h>
> #include <asm/arch/gpio.h>
> #include <asm/arch/mmc.h>
> #include <asm/arch/pinmux.h>
> @@ -95,59 +96,13 @@ void dram_init_banksize(void)
> PHYS_SDRAM_8_SIZE);
> }
>
> -#ifdef CONFIG_OF_CONTROL
> -static int decode_sromc(const void *blob, struct fdt_sromc *config)
> -{
> - int err;
> - int node;
> -
> - node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_SROMC);
> - if (node < 0) {
> - debug("Could not find SROMC node\n");
> - return node;
> - }
> -
> - config->bank = fdtdec_get_int(blob, node, "bank", 0);
> - config->width = fdtdec_get_int(blob, node, "width", 2);
> -
> - err = fdtdec_get_int_array(blob, node, "srom-timing", config->timing,
> - FDT_SROM_TIMING_COUNT);
> - if (err < 0) {
> - debug("Could not decode SROMC configuration\n");
> - return -FDT_ERR_NOTFOUND;
> - }
> -
> - return 0;
> -}
> -#endif
> -
> int board_eth_init(bd_t *bis)
> {
> #ifdef CONFIG_SMC911X
> u32 smc_bw_conf, smc_bc_conf;
> struct fdt_sromc config;
> fdt_addr_t base_addr;
> - int node;
> -
> -#ifdef CONFIG_OF_CONTROL
> - node = decode_sromc(gd->fdt_blob, &config);
> - if (node < 0) {
> - debug("%s: Could not find sromc configuration\n", __func__);
> - return 0;
> - }
> - node = fdtdec_next_compatible(gd->fdt_blob, node, COMPAT_SMSC_LAN9215);
> - if (node < 0) {
> - debug("%s: Could not find lan9215 configuration\n", __func__);
> - return 0;
> - }
>
> - /* We now have a node, so any problems from now on are errors */
> - base_addr = fdtdec_get_addr(gd->fdt_blob, node, "reg");
> - if (base_addr == FDT_ADDR_T_NONE) {
> - debug("%s: Could not find lan9215 address\n", __func__);
> - return -1;
> - }
> -#else
> /* Non-FDT configuration - bank number and timing parameters*/
> config.bank = CONFIG_ENV_SROM_BANK;
> config.width = 2;
> @@ -160,7 +115,6 @@ int board_eth_init(bd_t *bis)
> config.timing[FDT_SROM_TACP] = 0x09;
> config.timing[FDT_SROM_PMC] = 0x01;
> base_addr = CONFIG_SMC911X_BASE;
> -#endif
>
> /* Ethernet needs data bus width of 16 bits */
> if (config.width != 2) {
> @@ -199,16 +153,31 @@ int checkboard(void)
> #ifdef CONFIG_GENERIC_MMC
> int board_mmc_init(bd_t *bis)
> {
> - int err;
> + int err = 0, ret = 0;
>
> err = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE);
> - if (err) {
> + if (err)
> debug("SDMMC0 not configured\n");
> - return err;
> - }
> -
> - err = s5p_mmc_init(0, 8);
> - return err;
> + ret |= err;
> +
> + /*EMMC: dwmmc Channel-0 with 8 bit bus width */
> + err = exynos_dwmmc_init(0, 8);
This is not really init of the whole dwmmc, only a port - suggest
exynos_dwmmc_add_port() or similar
> + if (err)
> + debug("dwmmc Channel-0 init failed\n");
> + ret |= err;
> +
> + err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE);
> + if (err)
> + debug("SDMMC2 not configured\n");
> + ret |= err;
> +
> + /*SD: dwmmc Channel-2 with 4 bit bus width */
> + err = exynos_dwmmc_init(2, 4);
> + if (err)
> + debug("dwmmc Channel-2 init failed\n");
> + ret |= err;
> +
> + return ret;
> }
> #endif
>
> @@ -243,6 +212,24 @@ static int board_uart_init(void)
> return 0;
> }
>
> +#ifdef CONFIG_SYS_I2C_INIT_BOARD
> +static int board_i2c_init(void)
> +{
> + int i, err;
> +
> + for (i = 0; i < CONFIG_MAX_I2C_NUM; i++) {
> + err = exynos_pinmux_config((PERIPH_ID_I2C0 + i),
> + PINMUX_FLAG_NONE);
> + if (err) {
> + debug("I2C%d not configured\n", (PERIPH_ID_I2C0 + i));
> + return err;
> + }
> + }
> + i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
> + return 0;
> +}
> +#endif
> +
> #ifdef CONFIG_BOARD_EARLY_INIT_F
> int board_early_init_f(void)
> {
> @@ -253,7 +240,7 @@ int board_early_init_f(void)
> return err;
> }
> #ifdef CONFIG_SYS_I2C_INIT_BOARD
> - board_i2c_init(gd->fdt_blob);
> + board_i2c_init();
> #endif
> return err;
> }
> diff --git a/include/configs/exynos5250-dt.h b/include/configs/exynos5250-dt.h
> index 59182f4..6ce73dc 100644
> --- a/include/configs/exynos5250-dt.h
> +++ b/include/configs/exynos5250-dt.h
> @@ -84,6 +84,8 @@
> #define CONFIG_MMC
> #define CONFIG_SDHCI
> #define CONFIG_S5P_SDHCI
> +#define CONFIG_DWMMC
> +#define CONFIG_EXYNOS_DWMMC
>
> #define CONFIG_BOARD_EARLY_INIT_F
>
> diff --git a/include/i2c.h b/include/i2c.h
> index c60d075..0944141 100644
> --- a/include/i2c.h
> +++ b/include/i2c.h
> @@ -263,6 +263,7 @@ extern int get_multi_sda_pin(void);
> extern int multi_i2c_init(void);
> #endif
>
> +#ifdef CONFIG_OF_CONTROL
> /**
> * Get FDT values for i2c bus.
> *
> @@ -270,6 +271,7 @@ extern int multi_i2c_init(void);
> * @return the number of I2C bus
> */
> void board_i2c_init(const void *blob);
> +#endif
Do you need this #ifdef? It would be better to avoid having the same
function with a different signature.
>
> /**
> * Find the I2C bus number by given a FDT I2C node.
> --
> 1.8.0
>
Regards,
Simon
More information about the U-Boot
mailing list