[U-Boot] [PATCH] powerpc/85xx: Add BSC9132QDS support
Prabhakar Kushwaha
prabhakar at freescale.com
Tue Jan 15 05:26:57 CET 2013
BSC9132QDS is a Freescale reference design board for BSC9132 SoC.
BSC9132 SOC is an integrated device that targets the evolving Microcell,
Picocell, and Enterprise-Femto base station market subsegments.
It combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.
BSC9132QDS Overview
--------------------
2Gbyte DDR3 (on board DDR), Dual Ranki
32Mbyte 16bit NOR flash
128Mbyte 2K page size NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
SD slot
USB-ULPI
eTSEC1: Connected to SGMII PHY
eTSEC2: Connected to SGMII PHY
PCIe
CPRI
SerDes
I2C RTC
DUART interface: supports one UARTs up to 115200 bps for console display
Apart from the above it also consists various peripherals to support DSP
functionalities.
This patch adds support for mainly Power side functionalities and peripherals
Signed-off-by: Naveen Burmi <NaveenBurmi at freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
---
MAINTAINERS | 4 +
board/freescale/bsc9132qds/Makefile | 52 +++
board/freescale/bsc9132qds/README | 150 +++++++
board/freescale/bsc9132qds/bsc9132qds.c | 406 +++++++++++++++++++
board/freescale/bsc9132qds/ddr.c | 209 ++++++++++
board/freescale/bsc9132qds/law.c | 35 ++
board/freescale/bsc9132qds/tlb.c | 92 +++++
boards.cfg | 6 +
include/configs/BSC9132QDS.h | 667 +++++++++++++++++++++++++++++++
9 files changed, 1621 insertions(+)
create mode 100644 board/freescale/bsc9132qds/Makefile
create mode 100644 board/freescale/bsc9132qds/README
create mode 100644 board/freescale/bsc9132qds/bsc9132qds.c
create mode 100644 board/freescale/bsc9132qds/ddr.c
create mode 100644 board/freescale/bsc9132qds/law.c
create mode 100644 board/freescale/bsc9132qds/tlb.c
create mode 100644 include/configs/BSC9132QDS.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 28c052d..d3ed390 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -27,6 +27,10 @@ Poonam Aggrwal <poonam.aggrwal at freescale.com>
BSC9131RDB BSC9131
+Naveen Burmi <NaveenBurmi at freescale.com>
+
+ BSC9132QDS BSC9132
+
Greg Allen <gallen at arlut.utexas.edu>
UTX8245 MPC8245
diff --git a/board/freescale/bsc9132qds/Makefile b/board/freescale/bsc9132qds/Makefile
new file mode 100644
index 0000000..267400b
--- /dev/null
+++ b/board/freescale/bsc9132qds/Makefile
@@ -0,0 +1,52 @@
+#
+# Copyright 2013 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS-y += $(BOARD).o
+COBJS-y += ddr.o
+COBJS-y += law.o
+COBJS-y += tlb.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS-y))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS))
+
+clean:
+ rm -f $(OBJS) $(SOBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/bsc9132qds/README b/board/freescale/bsc9132qds/README
new file mode 100644
index 0000000..4a3dbfe
--- /dev/null
+++ b/board/freescale/bsc9132qds/README
@@ -0,0 +1,150 @@
+Overview
+--------
+ The BSC9132 is a highly integrated device that targets the evolving
+ Microcell, Picocell, and Enterprise-Femto base station market subsegments.
+
+ The BSC9132 device combines Power Architecture e500 and DSP StarCore SC3850
+ core technologies with MAPLE-B2P baseband acceleration processing elements
+ to address the need for a high performance, low cost, integrated solution
+ that handles all required processing layers without the need for an
+ external device except for an RF transceiver or, in a Micro base station
+ configuration, a host device that handles the L3/L4 and handover between
+ sectors.
+
+ The BSC9132 SoC includes the following function and features:
+ - Power Architecture subsystem including two e500 processors with
+ 512-Kbyte shared L2 cache
+ - Two StarCore SC3850 DSP subsystems, each with a 512-Kbyte private L2
+ cache
+ - 32 Kbyte of shared M3 memory
+ - The Multi Accelerator Platform Engine for Pico BaseStation Baseband
+ Processing (MAPLE-B2P)
+ - Two DDR3/3L memory interfaces with 32-bit data width (40 bits including
+ ECC), up to 1333 MHz data rate
+ - Dedicated security engine featuring trusted boot
+ - Two DMA controllers
+ - OCNDMA with four bidirectional channels
+ - SysDMA with sixteen bidirectional channels
+ - Interfaces
+ - Four-lane SerDes PHY
+ - PCI Express controller complies with the PEX Specification-Rev 2.0
+ - Two Common Public Radio Interface (CPRI) controller lanes
+ - High-speed USB 2.0 host and device controller with ULPI interface
+ - Enhanced secure digital (SD/MMC) host controller (eSDHC)
+ - Antenna interface controller (AIC), supporting four industry
+ standard JESD207/four custom ADI RF interfaces
+ - ADI lanes support both full duplex FDD support & half duplex TDD
+ - Universal Subscriber Identity Module (USIM) interface that
+ facilitates communication to SIM cards or Eurochip pre-paid phone
+ cards
+ - Two DUART, two eSPI, and two I2C controllers
+ - Integrated Flash memory controller (IFC)
+ - GPIO
+ - Sixteen 32-bit timers
+
+The SC3850 core subsystem consists of the following:
+ - 32 KB, 8-way, level 1 instruction cache (L1 ICache)
+ - 32 KB, 8-way, level 1 data cache (L1 DCache)
+ - 512 KB, 8-way, level 2 unified instruction/data cache (L2 cache/M2 memory)
+ - Memory management unit (MMU)
+ - Global interrupt controller ( GIC)
+ - Debug and profiling unit (DPU)
+ - Two 32-bit quad timers
+
+BSC9132QDS board Overview
+-------------------------
+ 2Gbyte DDR3 (on board DDR), Dual Ranki
+ 32Mbyte 16bit NOR flash
+ 128Mbyte 2K page size NAND Flash
+ 256 Kbit M24256 I2C EEPROM
+ 128 Mbit SPI Flash memory
+ SD slot
+ USB-ULPI
+ eTSEC1: Connected to SGMII PHY
+ eTSEC2: Connected to SGMII PHY
+ PCIe
+ CPRI
+ SerDes
+ I2C RTC
+ DUART interface: supports one UARTs up to 115200 bps for console display
+
+Frequency Combinations Supported
+--------------------------------
+Core MHz/CCB MHz/DDR(MT/s)
+1. CPU0/CPU1/CCB/DDR: 1000MHz/1000MHz/500MHz/800MHz
+ (SYSCLK = 100MHz, DDRCLK = 100MHz)
+2. CPU0/CPU1/CCB/DDR: 1200MHz/1200MHz/600MHz/1330MHz
+ (SYSCLK = 100MHz, DDRCLK = 133MHz)
+
+Boot Methods Supported
+-----------------------
+1. NOR Flash
+2. NAND Flash
+3. SD Card
+4. SPI flash
+
+Default Boot Method
+--------------------
+NOR boot
+
+Building U-boot
+--------------
+To build the u-boot for BSC9132QDS:
+1. NOR Flash
+ make BSC9132QDS_NOR_DDRCLK100 : For 100MHZ DDR CLK
+ make BSC9132QDS_NOR_DDRCLK133 : For 133MHZ DDR CLK
+2. NAND Flash : It is currently not supported
+3. SPI Flash
+ make BSC9132QDS_SPIFLASH_DDRCLK100 : For 100MHZ DDR CLK
+ make BSC9132QDS_SPIFLASH_DDRCLK133 : For 133MHZ DDR CLK
+4. SD Card
+ make BSC9132QDS_SDCARD_DDRCLK100 : For 100MHZ DDR CLK
+ make BSC9132QDS_SDCARD_DDRCLK133 : For 133MHZ DDR CLK
+
+Memory map
+-----------
+ 0x0000_0000 0x7FFF_FFFF DDR 2G cacheable
+ 0x8000_0000 0x8FFF_FFFF NOR Flash 256M
+ 0x9000_0000 0x9FFF_FFFF PCIe Memory 256M
+ 0xA000_0000 0xA7FF_FFFF DSP core1 L2 space 128M
+ 0xB000_0000 0xB0FF_FFFF DSP core0 M2 space 16M
+ 0xB100_0000 0xB1FF_FFFF DSP core1 M2 space 16M
+ 0xC000_0000 0xC000_7FFF M3 Memory 32K
+ 0xC001_0000 0xC001_FFFF PCI Express I/O 64K
+ 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M
+ 0xC1F0_0000 0xC1F7_FFFF PA SRAM Region 0 512K
+ 0xC1F8_0000 0xC1FB_FFFF PA SRAM Region 1 512K
+ 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K
+ 0xFEE0_0000 0xFEE0_0FFF DSP Boot ROM 4K
+ 0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M
+ 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M
+ 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND Buffer 8M
+
+Flashing Images
+---------------
+To place a new u-boot image in the NAND flash and then boot
+with that new image temporarily, use this:
+ tftp 1000000 u-boot-nand.bin
+ nand erase 0 100000
+ nand write 1000000 0 100000
+ reset
+
+Using the Device Tree Source File
+---------------------------------
+To create the DTB (Device Tree Binary) image file,
+use a command similar to this:
+
+ dtc -b 0 -f -I dts -O dtb bsc9132qds.dts > bsc9132qds.dtb
+
+Likely, that .dts file will come from here;
+
+ linux-2.6/arch/powerpc/boot/dts/bsc9132qds.dts
+
+Booting Linux
+-------------
+Place a linux uImage in the TFTP disk area.
+
+ tftp 1000000 uImage
+ tftp 2000000 rootfs.ext2.gz.uboot
+ tftp c00000 bsc9132qds.dtb
+ bootm 1000000 2000000 c00000
diff --git a/board/freescale/bsc9132qds/bsc9132qds.c b/board/freescale/bsc9132qds/bsc9132qds.c
new file mode 100644
index 0000000..9f0eaa5
--- /dev/null
+++ b/board/freescale/bsc9132qds/bsc9132qds.c
@@ -0,0 +1,406 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/io.h>
+#include <miiphy.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <fsl_mdio.h>
+#include <tsec.h>
+#include <mmc.h>
+#include <netdev.h>
+#include <asm/fsl_ifc.h>
+#include <hwconfig.h>
+#include <i2c.h>
+#include <asm/fsl_ddr_sdram.h>
+
+#ifdef CONFIG_PCI
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#endif
+
+#include "../common/qixis.h"
+DECLARE_GLOBAL_DATA_PTR;
+
+
+int board_early_init_f(void)
+{
+ struct fsl_ifc *ifc = (void *)CONFIG_SYS_IFC_ADDR;
+
+ setbits_be32(&ifc->ifc_gcr, 1 << IFC_GCR_TBCTL_TRN_TIME_SHIFT);
+
+ return 0;
+}
+
+void board_config_serdes_mux(void)
+{
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 pordevsr = in_be32(&gur->pordevsr);
+ u32 srds_cfg = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >>
+ MPC85xx_PORDEVSR_IO_SEL_SHIFT;
+
+ switch (srds_cfg) {
+ /* PEX(1) PEX(2) CPRI 2 CPRI 1 */
+ case 1:
+ case 2:
+ case 3:
+ case 4:
+ case 5:
+ case 22:
+ case 23:
+ case 24:
+ case 25:
+ case 26:
+ QIXIS_WRITE_I2C(brdcfg[4], 0x03);
+ break;
+
+ /* PEX(1) PEX(2) SGMII1 CPRI 1 */
+ case 6:
+ case 7:
+ case 8:
+ case 9:
+ case 10:
+ case 27:
+ case 28:
+ case 29:
+ case 30:
+ case 31:
+ QIXIS_WRITE_I2C(brdcfg[4], 0x01);
+ break;
+
+ /* PEX(1) PEX(2) SGMII1 SGMII2 */
+ case 11:
+ case 32:
+ QIXIS_WRITE_I2C(brdcfg[4], 0x00);
+ break;
+
+ /* PEX(1) SGMII2 CPRI 2 CPRI 1 */
+ case 12:
+ case 13:
+ case 14:
+ case 15:
+ case 16:
+ case 33:
+ case 34:
+ case 35:
+ case 36:
+ case 37:
+ QIXIS_WRITE_I2C(brdcfg[4], 0x07);
+ break;
+
+ /* PEX(1) SGMII2 SGMII1 CPRI 1 */
+ case 17:
+ case 18:
+ case 19:
+ case 20:
+ case 21:
+ case 38:
+ case 39:
+ case 40:
+ case 41:
+ case 42:
+ QIXIS_WRITE_I2C(brdcfg[4], 0x05);
+ break;
+
+ /* SGMII1 SGMII2 CPRI 2 CPRI 1 */
+ case 43:
+ case 44:
+ case 45:
+ case 46:
+ case 47:
+ QIXIS_WRITE_I2C(brdcfg[4], 0x0F);
+ break;
+
+
+ default:
+ break;
+ }
+}
+
+int board_early_init_r(void)
+{
+#ifndef CONFIG_SYS_NO_FLASH
+ const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+ const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+ /*
+ * Remap Boot flash region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ /* invalidate existing TLB entry for flash */
+ disable_tlb(flash_esel);
+
+ set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel, BOOKE_PAGESZ_64M, 1);
+
+ set_tlb(1, flashbase + 0x4000000,
+ CONFIG_SYS_FLASH_BASE_PHYS + 0x4000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel+1, BOOKE_PAGESZ_64M, 1);
+#endif
+ board_config_serdes_mux();
+ return 0;
+}
+
+#ifdef CONFIG_PCI
+void pci_init_board(void)
+{
+ fsl_pcie_init_board(0);
+}
+#endif /* ifdef CONFIG_PCI */
+
+int checkboard(void)
+{
+ struct cpu_type *cpu;
+ u8 sw;
+
+ cpu = gd->cpu;
+ printf("Board: %sQDS\n", cpu->name);
+
+ printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, FPGA Ver: 0x%02x,\n",
+ QIXIS_READ(id), QIXIS_READ(arch), QIXIS_READ(scver));
+
+ sw = QIXIS_READ(brdcfg[0]);
+ sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
+
+ printf("IFC chip select:");
+ switch (sw) {
+ case 0:
+ printf("NOR\n");
+ break;
+ case 2:
+ printf("Promjet\n");
+ break;
+ case 4:
+ printf("NAND\n");
+ break;
+ default:
+ printf("Invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
+ break;
+ }
+
+ return 0;
+}
+
+#ifdef CONFIG_TSEC_ENET
+int board_eth_init(bd_t *bis)
+{
+ struct fsl_pq_mdio_info mdio_info;
+ struct tsec_info_struct tsec_info[4];
+ int num = 0;
+
+#ifdef CONFIG_TSEC1
+ SET_STD_TSEC_INFO(tsec_info[num], 1);
+ num++;
+
+#endif
+
+#ifdef CONFIG_TSEC2
+ SET_STD_TSEC_INFO(tsec_info[num], 2);
+ num++;
+#endif
+
+ mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
+ mdio_info.name = DEFAULT_MII_NAME;
+
+ fsl_pq_mdio_init(bis, &mdio_info);
+ tsec_eth_init(bis, tsec_info, num);
+
+ #ifdef CONFIG_PCI
+ pci_eth_init(bis);
+ #endif
+
+ return 0;
+}
+#endif
+
+#define USBMUX_SEL_MASK 0xc0
+#define USBMUX_SEL_UART2 0xc0
+#define USBMUX_SEL_USB 0x40
+#define SPIMUX_SEL_UART3 0x80
+#define GPS_MUX_SEL_GPS 0x40
+
+#define TSEC_1588_CLKIN_MASK 0x03
+#define CON_XCVR_REF_CLK 0x00
+
+int misc_init_r(void)
+{
+ u8 val;
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 porbmsr = in_be32(&gur->porbmsr);
+ u32 romloc = (porbmsr >> MPC85XX_PORBMSR_ROMLOC_SHIFT) & 0xf;
+
+ /*Configure 1588 clock-in source from RF Card*/
+ val = QIXIS_READ_I2C(brdcfg[5]);
+ QIXIS_WRITE_I2C(brdcfg[5],
+ (val & ~(TSEC_1588_CLKIN_MASK)) | CON_XCVR_REF_CLK);
+
+ if (hwconfig("uart2") && hwconfig("usb1")) {
+ printf("UART2 and USB cannot work together on the board\n");
+ printf("Remove one from hwconfig and reset\n");
+ } else {
+ if (hwconfig("uart2")) {
+ val = QIXIS_READ_I2C(brdcfg[5]);
+ QIXIS_WRITE_I2C(brdcfg[5],
+ (val & ~(USBMUX_SEL_MASK)) | USBMUX_SEL_UART2);
+ clrbits_be32(&gur->pmuxcr3,
+ MPC85xx_PMUXCR3_USB_SEL_MASK);
+ setbits_be32(&gur->pmuxcr3, MPC85xx_PMUXCR3_UART2_SEL);
+ } else {
+ /* By default USB should be selected.
+ * Programming FPGA to select USB. */
+ val = QIXIS_READ_I2C(brdcfg[5]);
+ QIXIS_WRITE_I2C(brdcfg[5],
+ (val & ~(USBMUX_SEL_MASK)) | USBMUX_SEL_USB);
+ }
+
+ }
+
+ if (hwconfig("sim")) {
+ if (romloc == PORBMSR_ROMLOC_NAND_2K ||
+ romloc == PORBMSR_ROMLOC_NOR ||
+ romloc == PORBMSR_ROMLOC_SPI) {
+
+ val = QIXIS_READ_I2C(brdcfg[3]);
+ QIXIS_WRITE_I2C(brdcfg[3], val|0x10);
+ clrbits_be32(&gur->pmuxcr,
+ MPC85xx_PMUXCR0_SIM_SEL_MASK);
+ setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR0_SIM_SEL);
+ }
+ }
+
+ if (hwconfig("uart3")) {
+ if (romloc == PORBMSR_ROMLOC_NAND_2K ||
+ romloc == PORBMSR_ROMLOC_NOR ||
+ romloc == PORBMSR_ROMLOC_SDHC) {
+
+ /* UART3 and SPI1 (Flashes) are muxed together */
+ val = QIXIS_READ_I2C(brdcfg[3]);
+ QIXIS_WRITE_I2C(brdcfg[3], (val | SPIMUX_SEL_UART3));
+ clrbits_be32(&gur->pmuxcr3,
+ MPC85xx_PMUXCR3_UART3_SEL_MASK);
+ setbits_be32(&gur->pmuxcr3, MPC85xx_PMUXCR3_UART3_SEL);
+
+ /* MUX to select UART3 connection to J24 header
+ * or to GPS */
+ val = QIXIS_READ_I2C(brdcfg[6]);
+ if (hwconfig("gps"))
+ QIXIS_WRITE_I2C(brdcfg[6],
+ (val | GPS_MUX_SEL_GPS));
+ else
+ QIXIS_WRITE_I2C(brdcfg[6],
+ (val & ~(GPS_MUX_SEL_GPS)));
+ }
+ }
+ return 0;
+}
+
+void fdt_del_node_compat(void *blob, const char *compatible)
+{
+ int err;
+ int off = fdt_node_offset_by_compatible(blob, -1, compatible);
+ if (off < 0) {
+ printf("WARNING: could not find compatible node %s: %s.\n",
+ compatible, fdt_strerror(off));
+ return;
+ }
+ err = fdt_del_node(blob, off);
+ if (err < 0) {
+ printf("WARNING: could not remove %s: %s.\n",
+ compatible, fdt_strerror(err));
+ }
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+ struct cpu_type *cpu;
+
+ cpu = gd->cpu;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ #if defined(CONFIG_PCI)
+ FT_FSL_PCI_SETUP;
+ #endif
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 porbmsr = in_be32(&gur->porbmsr);
+ u32 romloc = (porbmsr >> MPC85XX_PORBMSR_ROMLOC_SHIFT) & 0xf;
+
+ if (!(hwconfig("uart2") && hwconfig("usb1"))) {
+ /* If uart2 is there in hwconfig remove usb node from
+ * device tree */
+
+ if (hwconfig("uart2")) {
+ /* remove dts usb node */
+ fdt_del_node_compat(blob, "fsl-usb2-dr");
+ } else {
+ fdt_fixup_dr_usb(blob, bd);
+ fdt_del_node_and_alias(blob, "serial2");
+ }
+ }
+
+ if (hwconfig("uart3")) {
+ if (romloc == PORBMSR_ROMLOC_NAND_2K ||
+ romloc == PORBMSR_ROMLOC_NOR ||
+ romloc == PORBMSR_ROMLOC_SDHC)
+ /* Delete SPI node from the device tree */
+ fdt_del_node_and_alias(blob, "spi1");
+ } else
+ fdt_del_node_and_alias(blob, "serial3");
+
+ if (hwconfig("sim")) {
+ if (romloc == PORBMSR_ROMLOC_NAND_2K ||
+ romloc == PORBMSR_ROMLOC_NOR ||
+ romloc == PORBMSR_ROMLOC_SPI) {
+
+ /* remove dts sdhc node */
+ fdt_del_node_compat(blob, "fsl,esdhc");
+ } else if (romloc == PORBMSR_ROMLOC_SDHC) {
+
+ /* remove dts sim node */
+ fdt_del_node_compat(blob, "fsl,sim-v1.0");
+ printf("SIM & SDHC can't work together on the board");
+ printf("\nRemove sim from hwconfig and reset\n");
+ }
+ }
+}
+#endif
diff --git a/board/freescale/bsc9132qds/ddr.c b/board/freescale/bsc9132qds/ddr.c
new file mode 100644
index 0000000..946ad19
--- /dev/null
+++ b/board/freescale/bsc9132qds/ddr.c
@@ -0,0 +1,209 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+#include <asm/immap_85xx.h>
+#include <asm/processor.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+#include <asm/io.h>
+#include <asm/fsl_law.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifndef CONFIG_SYS_DDR_RAW_TIMING
+
+fsl_ddr_cfg_regs_t ddr_cfg_regs_800 = {
+ .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS,
+ .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG,
+ .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2,
+ .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_800,
+ .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_800,
+ .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_800,
+ .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_800,
+ .ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL,
+ .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2,
+ .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_800,
+ .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_800,
+ .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL,
+ .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_800,
+ .ddr_data_init = CONFIG_MEM_INIT_VALUE,
+ .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_800,
+ .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR,
+ .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR,
+ .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4,
+ .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5,
+ .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL,
+ .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL_800,
+ .ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR,
+ .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1,
+ .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2
+};
+
+fsl_ddr_cfg_regs_t ddr_cfg_regs_1333 = {
+ .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS,
+ .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG,
+ .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2,
+ .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_1333,
+ .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_1333,
+ .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_1333,
+ .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_1333,
+ .ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL,
+ .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2,
+ .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_1333,
+ .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_1333,
+ .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL,
+ .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_1333,
+ .ddr_data_init = CONFIG_MEM_INIT_VALUE,
+ .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_1333,
+ .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR,
+ .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR,
+ .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4,
+ .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5,
+ .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL,
+ .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL_1333,
+ .ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR,
+ .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1,
+ .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2
+};
+
+
+fixed_ddr_parm_t fixed_ddr_parm_0[] = {
+ {750, 850, &ddr_cfg_regs_800},
+ {1060, 1333, &ddr_cfg_regs_1333},
+ {0, 0, NULL}
+};
+
+/*
+ * Fixed sdram init -- doesn't use serial presence detect.
+ */
+phys_size_t fixed_sdram(void)
+{
+ int i;
+ char buf[32];
+ fsl_ddr_cfg_regs_t ddr_cfg_regs;
+ phys_size_t ddr_size;
+ ulong ddr_freq, ddr_freq_mhz;
+
+ ddr_freq = get_ddr_freq(0);
+ ddr_freq_mhz = ddr_freq / 1000000;
+
+ printf("Configuring DDR for %s MT/s data rate\n",
+ strmhz(buf, ddr_freq));
+
+ for (i = 0; fixed_ddr_parm_0[i].max_freq > 0; i++) {
+ if ((ddr_freq_mhz > fixed_ddr_parm_0[i].min_freq) &&
+ (ddr_freq_mhz <= fixed_ddr_parm_0[i].max_freq)) {
+ memcpy(&ddr_cfg_regs, fixed_ddr_parm_0[i].ddr_settings,
+ sizeof(ddr_cfg_regs));
+ break;
+ }
+ }
+
+ if (fixed_ddr_parm_0[i].max_freq == 0)
+ panic("Unsupported DDR data rate %s MT/s data rate\n",
+ strmhz(buf, ddr_freq));
+
+ ddr_size = (phys_size_t) CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
+ fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0);
+
+ if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE, ddr_size,
+ LAW_TRGT_IF_DDR_1) < 0) {
+ printf("ERROR setting Local Access Windows for DDR\n");
+ return 0;
+ }
+
+ return ddr_size;
+}
+
+#else /* CONFIG_SYS_DDR_RAW_TIMING */
+/* Micron MT41J512M8_187E */
+dimm_params_t ddr_raw_timing = {
+ .n_ranks = 1,
+ .rank_density = 1073741824u,
+ .capacity = 1073741824u,
+ .primary_sdram_width = 32,
+ .ec_sdram_width = 0,
+ .registered_dimm = 0,
+ .mirrored_dimm = 0,
+ .n_row_addr = 15,
+ .n_col_addr = 10,
+ .n_banks_per_sdram_device = 8,
+ .edc_config = 0,
+ .burst_lengths_bitmask = 0x0c,
+
+ .tCKmin_X_ps = 1870,
+ .caslat_X = 0x1e << 4, /* 5,6,7,8 */
+ .tAA_ps = 13125,
+ .tWR_ps = 15000,
+ .tRCD_ps = 13125,
+ .tRRD_ps = 7500,
+ .tRP_ps = 13125,
+ .tRAS_ps = 37500,
+ .tRC_ps = 50625,
+ .tRFC_ps = 160000,
+ .tWTR_ps = 7500,
+ .tRTP_ps = 7500,
+ .refresh_rate_ps = 7800000,
+ .tFAW_ps = 37500,
+};
+
+int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
+ unsigned int controller_number,
+ unsigned int dimm_number)
+{
+ const char dimm_model[] = "Fixed DDR on board";
+
+ if ((controller_number == 0) && (dimm_number == 0)) {
+ memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
+ memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
+ memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
+ }
+
+ return 0;
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ int i;
+ popts->clk_adjust = 6;
+ popts->cpo_override = 0x1f;
+ popts->write_data_delay = 2;
+ popts->half_strength_driver_enable = 1;
+ /* Write leveling override */
+ popts->wrlvl_en = 1;
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+ popts->wrlvl_start = 0x8;
+ popts->trwt_override = 1;
+ popts->trwt = 0;
+
+ for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+ popts->cs_local_opts[i].odt_rd_cfg = FSL_DDR_ODT_NEVER;
+ popts->cs_local_opts[i].odt_wr_cfg = FSL_DDR_ODT_CS;
+ }
+}
+
+#endif /* CONFIG_SYS_DDR_RAW_TIMING */
diff --git a/board/freescale/bsc9132qds/law.c b/board/freescale/bsc9132qds/law.c
new file mode 100644
index 0000000..dc23658
--- /dev/null
+++ b/board/freescale/bsc9132qds/law.c
@@ -0,0 +1,35 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+#ifndef CONFIG_SYS_NO_FLASH
+ SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_128M, LAW_TRGT_IF_IFC),
+#endif
+ SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_IFC),
+ SET_LAW(CONFIG_SYS_FPGA_BASE_PHYS, LAW_SIZE_128K, LAW_TRGT_IF_IFC),
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/bsc9132qds/tlb.c b/board/freescale/bsc9132qds/tlb.c
new file mode 100644
index 0000000..0e4545f
--- /dev/null
+++ b/board/freescale/bsc9132qds/tlb.c
@@ -0,0 +1,92 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 ,
+ CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 ,
+ CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 ,
+ CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* TLB 1 */
+ /* *I*** - Covers boot page */
+ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_4K, 1),
+
+ /* *I*G* - CCSRBAR (PA) */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_1M, 1),
+
+ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_64M, 1),
+
+ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE + 0x4000000,
+ CONFIG_SYS_FLASH_BASE_PHYS + 0x4000000,
+ MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 4, BOOKE_PAGESZ_64M, 1),
+
+#if defined(CONFIG_SYS_RAMBOOT)
+ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 8, BOOKE_PAGESZ_1G, 1),
+#endif
+
+#ifdef CONFIG_PCI
+ /* *I*G* - PCI */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCI I/O */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 7, BOOKE_PAGESZ_64K, 1),
+#endif
+
+ /* *I*G - Board FPGA */
+ SET_TLB_ENTRY(1, CONFIG_SYS_FPGA_BASE, CONFIG_SYS_FPGA_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 9, BOOKE_PAGESZ_256K, 1),
+
+ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 5, BOOKE_PAGESZ_1M, 1),
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/boards.cfg b/boards.cfg
index 91504c0..4691a2a 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -854,6 +854,12 @@ P5020DS_SPIFLASH powerpc mpc85xx corenet_ds freescale
P5020DS_SRIO_PCIE_BOOT powerpc mpc85xx corenet_ds freescale - P5020DS:SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000
P5040DS powerpc mpc85xx corenet_ds freescale
BSC9131RDB_SPIFLASH powerpc mpc85xx bsc9131rdb freescale - BSC9131RDB:BSC9131RDB,SPIFLASH
+BSC9132QDS_NOR_DDRCLK100 powerpc mpc85xx bsc9132qds freescale - BSC9132QDS:BSC9132QDS,SYS_CLK_100_DDR_100
+BSC9132QDS_NOR_DDRCLK133 powerpc mpc85xx bsc9132qds freescale - BSC9132QDS:BSC9132QDS,SYS_CLK_100_DDR_133
+BSC9132QDS_SDCARD_DDRCLK100 powerpc mpc85xx bsc9132qds freescale - BSC9132QDS:BSC9132QDS,SDCARD,SYS_CLK_100_DDR_100
+BSC9132QDS_SDCARD_DDRCLK133 powerpc mpc85xx bsc9132qds freescale - BSC9132QDS:BSC9132QDS,SDCARD,SYS_CLK_100_DDR_133
+BSC9132QDS_SPIFLASH_DDRCLK100 powerpc mpc85xx bsc9132qds freescale - BSC9132QDS:BSC9132QDS,SPIFLASH,SYS_CLK_100_DDR_100
+BSC9132QDS_SPIFLASH_DDRCLK133 powerpc mpc85xx bsc9132qds freescale - BSC9132QDS:BSC9132QDS,SPIFLASH,SYS_CLK_100_DDR_133
stxgp3 powerpc mpc85xx stxgp3 stx
stxssa powerpc mpc85xx stxssa stx - stxssa
stxssa_4M powerpc mpc85xx stxssa stx - stxssa:STXSSA_4M
diff --git a/include/configs/BSC9132QDS.h b/include/configs/BSC9132QDS.h
new file mode 100644
index 0000000..431c686
--- /dev/null
+++ b/include/configs/BSC9132QDS.h
@@ -0,0 +1,667 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * BSC9132 QDS board configuration file
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#ifdef CONFIG_BSC9132QDS
+#define CONFIG_BSC9132
+#endif
+
+#define CONFIG_MISC_INIT_R
+
+#ifdef CONFIG_SDCARD
+#define CONFIG_RAMBOOT_SDCARD
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_SYS_TEXT_BASE 0x11000000
+#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
+#endif
+#define CONFIG_SYS_FSL_ERRATUM_IFC_A002769 1
+#ifdef CONFIG_SPIFLASH
+#define CONFIG_RAMBOOT_SPIFLASH
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_SYS_TEXT_BASE 0x11000000
+#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0x8ff80000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS 0x8ffffffc
+#endif
+
+#ifndef CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+#endif
+
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE /* BOOKE */
+#define CONFIG_E500 /* BOOKE e500 family */
+#define CONFIG_MPC85xx
+#define CONFIG_FSL_IFC /* Enable IFC Support */
+#define CONFIG_SYS_HAS_SERDES /* common SERDES init code */
+
+#define CONFIG_PCI /* Enable PCI/PCIE */
+#if defined(CONFIG_PCI)
+#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */
+#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
+
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+
+#define CONFIG_E1000 /* E1000 pci Ethernet card*/
+
+/*
+ * PCI Windows
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+/* controller 1, Slot 1, tgtid 1, Base address a000 */
+#define CONFIG_SYS_PCIE1_NAME "PCIe Slot"
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0x90000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0x90000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0x90000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xC0010000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xC0010000
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif
+
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_TSEC_ENET /* ethernet */
+
+#if defined(CONFIG_SYS_CLK_100_DDR_100)
+#define CONFIG_SYS_CLK_FREQ 100000000
+#define CONFIG_DDR_CLK_FREQ 100000000
+#elif defined(CONFIG_SYS_CLK_100_DDR_133)
+#define CONFIG_SYS_CLK_FREQ 100000000
+#define CONFIG_DDR_CLK_FREQ 133000000
+#endif
+
+#define CONFIG_MP
+
+#define CONFIG_HWCONFIG
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* enable branch predition */
+
+#define CONFIG_SYS_MEMTEST_START 0x01000000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x01ffffff
+
+/* DDR Setup */
+#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#define SPD_EEPROM_ADDRESS1 0x54 /* I2C access */
+#define SPD_EEPROM_ADDRESS2 0x56 /* I2C access */
+#define CONFIG_FSL_DDR_INTERACTIVE
+
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
+#define CONFIG_SYS_SDRAM_SIZE (1024)
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+
+/* DDR3 Controller Settings */
+#define CONFIG_CHIP_SELECTS_PER_CTRL 1
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F
+#define CONFIG_SYS_DDR_CS0_CONFIG_1333 0x80004302
+#define CONFIG_SYS_DDR_CS0_CONFIG_800 0x80014302
+#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000
+#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
+#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000
+#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000
+#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000
+#define CONFIG_SYS_DDR1_CS0_BNDS 0x0040007F
+
+#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600
+#define CONFIG_SYS_DDR_SR_CNTR 0x00000000
+#define CONFIG_SYS_DDR_RCW_1 0x00000000
+#define CONFIG_SYS_DDR_RCW_2 0x00000000
+#define CONFIG_SYS_DDR_CONTROL_800 0x470C0000
+#define CONFIG_SYS_DDR_CONTROL_2_800 0x04401050
+#define CONFIG_SYS_DDR_TIMING_4_800 0x00220001
+#define CONFIG_SYS_DDR_TIMING_5_800 0x03402400
+
+#define CONFIG_SYS_DDR_CONTROL_1333 0x470C0008
+#define CONFIG_SYS_DDR_CONTROL_2_1333 0x24401010
+#define CONFIG_SYS_DDR_TIMING_4_1333 0x00000001
+#define CONFIG_SYS_DDR_TIMING_5_1333 0x03401400
+
+#define CONFIG_SYS_DDR_TIMING_3_800 0x00020000
+#define CONFIG_SYS_DDR_TIMING_0_800 0x00330004
+#define CONFIG_SYS_DDR_TIMING_1_800 0x6f6B4846
+#define CONFIG_SYS_DDR_TIMING_2_800 0x0FA8C8CF
+#define CONFIG_SYS_DDR_CLK_CTRL_800 0x03000000
+#define CONFIG_SYS_DDR_MODE_1_800 0x40461520
+#define CONFIG_SYS_DDR_MODE_2_800 0x8000c000
+#define CONFIG_SYS_DDR_INTERVAL_800 0x0C300000
+#define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8655A608
+
+#define CONFIG_SYS_DDR_TIMING_3_1333 0x01061000
+#define CONFIG_SYS_DDR_TIMING_0_1333 0x00440104
+#define CONFIG_SYS_DDR_TIMING_1_1333 0x98913A45
+#define CONFIG_SYS_DDR_TIMING_2_1333 0x0FB8B114
+#define CONFIG_SYS_DDR_CLK_CTRL_1333 0x02800000
+#define CONFIG_SYS_DDR_MODE_1_1333 0x00061A50
+#define CONFIG_SYS_DDR_MODE_2_1333 0x00100000
+#define CONFIG_SYS_DDR_INTERVAL_1333 0x144E0513
+#define CONFIG_SYS_DDR_WRLVL_CONTROL_1333 0x8655F607
+
+/*FIXME: the following params are constant w.r.t diff freq
+combinations. this should be removed later
+*/
+#if CONFIG_DDR_CLK_FREQ == 100000000
+#define CONFIG_SYS_DDR_CS0_CONFIG CONFIG_SYS_DDR_CS0_CONFIG_800
+#define CONFIG_SYS_DDR_CONTROL CONFIG_SYS_DDR_CONTROL_800
+#define CONFIG_SYS_DDR_CONTROL_2 CONFIG_SYS_DDR_CONTROL_2_800
+#define CONFIG_SYS_DDR_TIMING_4 CONFIG_SYS_DDR_TIMING_4_800
+#define CONFIG_SYS_DDR_TIMING_5 CONFIG_SYS_DDR_TIMING_5_800
+#elif CONFIG_DDR_CLK_FREQ == 133000000
+#define CONFIG_SYS_DDR_CS0_CONFIG CONFIG_SYS_DDR_CS0_CONFIG_1333
+#define CONFIG_SYS_DDR_CONTROL CONFIG_SYS_DDR_CONTROL_1333
+#define CONFIG_SYS_DDR_CONTROL_2 CONFIG_SYS_DDR_CONTROL_2_1333
+#define CONFIG_SYS_DDR_TIMING_4 CONFIG_SYS_DDR_TIMING_4_1333
+#define CONFIG_SYS_DDR_TIMING_5 CONFIG_SYS_DDR_TIMING_5_1333
+#else
+#define CONFIG_SYS_DDR_CS0_CONFIG CONFIG_SYS_DDR_CS0_CONFIG_800
+#define CONFIG_SYS_DDR_CONTROL CONFIG_SYS_DDR_CONTROL_800
+#define CONFIG_SYS_DDR_CONTROL_2 CONFIG_SYS_DDR_CONTROL_2_800
+#define CONFIG_SYS_DDR_TIMING_4 CONFIG_SYS_DDR_TIMING_4_800
+#define CONFIG_SYS_DDR_TIMING_5 CONFIG_SYS_DDR_TIMING_5_800
+#endif
+
+
+/* relocated CCSRBAR */
+#define CONFIG_SYS_CCSRBAR CONFIG_SYS_CCSRBAR_DEFAULT
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR_DEFAULT
+
+#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR
+
+/*
+ * IFC Definitions
+ */
+/* NOR Flash on IFC */
+#define CONFIG_SYS_FLASH_BASE 0x88000000
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* Max number of sector: 32M */
+
+#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
+
+#define CONFIG_SYS_NOR_CSPR 0x88000101
+#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
+#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(5)
+/* NOR Flash Timing Params */
+
+#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x01) \
+ | FTIM0_NOR_TEADC(0x03) \
+ | FTIM0_NOR_TAVDS(0x00) \
+ | FTIM0_NOR_TEAHC(0x0f))
+#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x1d) \
+ | FTIM1_NOR_TRAD_NOR(0x09) \
+ | FTIM1_NOR_TSEQRAD_NOR(0x09))
+#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x1) \
+ | FTIM2_NOR_TCH(0x4) \
+ | FTIM2_NOR_TWPH(0x7) \
+ | FTIM2_NOR_TWP(0x1e))
+#define CONFIG_SYS_NOR_FTIM3 0x0
+
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+/* CFI for NOR Flash */
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+
+/* NAND Flash on IFC */
+#define CONFIG_SYS_NAND_BASE 0xff800000
+#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
+
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+ | CSPR_MSEL_NAND /* MSEL = NAND */ \
+ | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
+
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_2 /* RAL = 2Byes */ \
+ | CSOR_NAND_PGS_2K /* Page Size = 2K */ \
+ | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
+ | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
+
+/* NAND Flash Timing Params */
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x03) \
+ | FTIM0_NAND_TWP(0x05) \
+ | FTIM0_NAND_TWCHT(0x02) \
+ | FTIM0_NAND_TWH(0x04))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x1c) \
+ | FTIM1_NAND_TWBE(0x1e) \
+ | FTIM1_NAND_TRR(0x07) \
+ | FTIM1_NAND_TRP(0x05))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x08) \
+ | FTIM2_NAND_TREH(0x04) \
+ | FTIM2_NAND_TWHRE(0x11))
+#define CONFIG_SYS_NAND_FTIM3 FTIM3_NAND_TWW(0x04)
+
+#define CONFIG_SYS_NAND_DDR_LAW 11
+
+/* NAND */
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+#define CONFIG_FSL_QIXIS
+#ifdef CONFIG_FSL_QIXIS
+#define CONFIG_SYS_FPGA_BASE 0xffb00000
+#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
+#define QIXIS_BASE CONFIG_SYS_FPGA_BASE
+#define QIXIS_LBMAP_SWITCH 9
+#define QIXIS_LBMAP_MASK 0x07
+#define QIXIS_LBMAP_SHIFT 0
+#define QIXIS_LBMAP_DFLTBANK 0x00
+#define QIXIS_LBMAP_ALTBANK 0x04
+#define QIXIS_RST_CTL_RESET 0x83
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
+
+#define CONFIG_SYS_FPGA_BASE_PHYS CONFIG_SYS_FPGA_BASE
+
+#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_FPGA_BASE) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_GPCM \
+ | CSPR_V)
+#define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024)
+#define CONFIG_SYS_CSOR2 0x0
+/* CPLD Timing parameters for IFC CS3 */
+#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
+ FTIM0_GPCM_TEADC(0x0e) | \
+ FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \
+ FTIM1_GPCM_TRAD(0x1f))
+#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
+ FTIM2_GPCM_TCH(0x0) | \
+ FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS2_FTIM3 0x0
+#endif
+
+/* Set up IFC registers for boot location NOR/NAND */
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
+
+#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_R
+
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
+#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END \
+ - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+
+#define CONFIG_SERIAL_MULTI 1 /* Enable both serial ports */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
+#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR + 0x4700)
+#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR + 0x4800)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER /* hush parser */
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#endif
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_SYS_I2C_SPEED 400800 /* I2C speed and slave address*/
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C2_OFFSET 0x3100
+
+/* I2C EEPROM */
+#define CONFIG_ID_EEPROM
+#ifdef CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#endif
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+
+/* enable read and write access to EEPROM */
+#define CONFIG_CMD_EEPROM
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+/* I2C FPGA */
+#define CONFIG_I2C_FPGA
+#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
+
+#define CONFIG_RTC_DS3231
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+
+/*
+ * SPI interface will not be available in case of NAND boot SPI CS0 will be
+ * used for SLIC
+ */
+/* eSPI - Enhanced SPI */
+#define CONFIG_FSL_ESPI /* SPI */
+#ifdef CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+#endif
+
+#if defined(CONFIG_TSEC_ENET)
+
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "eTSEC1"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "eTSEC2"
+
+#define TSEC1_PHY_ADDR 0
+#define TSEC2_PHY_ADDR 1
+
+#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+
+#define CONFIG_ETHPRIME "eTSEC1"
+
+#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+
+/* TBI PHY configuration for SGMII mode */
+#define CONFIG_TSEC_TBICR_SETTINGS ( \
+ TBICR_PHY_RESET \
+ | TBICR_ANEG_ENABLE \
+ | TBICR_FULL_DUPLEX \
+ | TBICR_SPEED1_SET \
+ )
+
+#endif /* CONFIG_TSEC_ENET */
+
+#define CONFIG_MMC
+#ifdef CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_DOS_PARTITION
+#define CONFIG_FSL_ESDHC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#endif
+
+#define CONFIG_USB_EHCI /* USB */
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_USB_STORAGE
+#define CONFIG_HAS_FSL_DR_USB
+#endif
+
+/*
+ * Environment
+ */
+#if defined(CONFIG_SYS_RAMBOOT)
+#if defined(CONFIG_RAMBOOT_SDCARD)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_SIZE 0x2000
+#elif defined(CONFIG_RAMBOOT_SPIFLASH)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 10000000
+#define CONFIG_ENV_SPI_MODE 0
+#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#define CONFIG_ENV_SIZE 0x2000
+#else
+#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
+#define CONFIG_ENV_SIZE 0x2000
+#endif
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
+#define CONFIG_ENV_ADDR 0xfff80000
+#else
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#endif
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+#endif
+
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
+
+#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+ /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq:1ms ticks */
+
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#endif
+
+#define CONFIG_HOSTNAME BSC9132qds
+#define CONFIG_ROOTPATH "/opt/nfsroot"
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_UBOOTPATH "u-boot.bin"
+
+#define CONFIG_BAUDRATE 115200
+
+#ifdef CONFIG_SDCARD
+#define CONFIG_DEF_HWCONFIG "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"
+#else
+#define CONFIG_DEF_HWCONFIG "hwconfig=sim;usb1:dr_mode=host,phy_type=ulpi\0"
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "uboot=" CONFIG_UBOOTPATH "\0" \
+ "loadaddr=1000000\0" \
+ "bootfile=uImage\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=rootfs.ext2.gz.uboot\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=bsc9132qds.dtb\0" \
+ "bdev=sda1\0" \
+ CONFIG_DEF_HWCONFIG\
+ "othbootargs=mem=880M ramdisk_size=600000 " \
+ "default_hugepagesz=256m hugepagesz=256m hugepages=1 " \
+ "isolcpus=0\0" \
+ "usbext2boot=setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs; " \
+ "usb start;" \
+ "ext2load usb 0:4 $loadaddr $bootfile;" \
+ "ext2load usb 0:4 $fdtaddr $fdtfile;" \
+ "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
+ "debug_halt_off=mw ff7e0e30 0xf0000000;"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_HDBOOT \
+ "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "usb start;" \
+ "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \
+ "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs; " \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+
+#endif /* __CONFIG_H */
--
1.7.9.5
More information about the U-Boot
mailing list