[U-Boot] [PATCH 10/10] mx23_olinuxino: Add ethernet support

[Otavio Salvador]

This adds support to the LAN9512 chip included in the board and extend
the environment to easy netboot use.

Signed-off-by: Otavio Salvador <otavio at ossystems.com.br>
---
 board/olimex/mx23_olinuxino/mx23_olinuxino.c |  6 +++++
 board/olimex/mx23_olinuxino/spl_boot.c       |  4 +++
 include/configs/mx23_olinuxino.h             | 40 +++++++++++++++++++++++++---
 3 files changed, 47 insertions(+), 3 deletions(-)

diff --git a/board/olimex/mx23_olinuxino/mx23_olinuxino.c b/board/olimex/mx23_olinuxino/mx23_olinuxino.c
index 2501417..9ed7718 100644
--- a/board/olimex/mx23_olinuxino/mx23_olinuxino.c
+++ b/board/olimex/mx23_olinuxino/mx23_olinuxino.c
@@ -23,6 +23,7 @@
  */
 
 #include <common.h>
+#include <asm/gpio.h>
 #include <asm/io.h>
 #include <asm/arch/iomux-mx23.h>
 #include <asm/arch/imx-regs.h>
@@ -45,6 +46,11 @@ int board_early_init_f(void)
 	/* SSP0 clock at 96MHz */
 	mxs_set_sspclk(MXC_SSPCLK0, 96000, 0);
 
+#ifdef CONFIG_CMD_USB
+	/* Enable LAN9512 */
+	gpio_direction_output(MX23_PAD_GPMI_ALE__GPIO_0_17, 1);
+#endif
+
 	return 0;
 }
 
diff --git a/board/olimex/mx23_olinuxino/spl_boot.c b/board/olimex/mx23_olinuxino/spl_boot.c
index 3bbf5ad..a96c293 100644
--- a/board/olimex/mx23_olinuxino/spl_boot.c
+++ b/board/olimex/mx23_olinuxino/spl_boot.c
@@ -95,6 +95,10 @@ const iomux_cfg_t iomux_setup[] = {
 	MX23_PAD_SSP1_DATA2__SSP1_DATA2 | MUX_CONFIG_SSP,
 	MX23_PAD_SSP1_DATA3__SSP1_DATA3 | MUX_CONFIG_SSP,
 	MX23_PAD_SSP1_SCK__SSP1_SCK | MUX_CONFIG_SSP,
+
+	/* Ethernet */
+	MX23_PAD_GPMI_ALE__GPIO_0_17 |
+		(MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_NOPULL),
 };
 
 void board_init_ll(void)
diff --git a/include/configs/mx23_olinuxino.h b/include/configs/mx23_olinuxino.h
index 7e17809..42de557 100644
--- a/include/configs/mx23_olinuxino.h
+++ b/include/configs/mx23_olinuxino.h
@@ -53,11 +53,13 @@
 #define	CONFIG_DOS_PARTITION
 
 #define	CONFIG_CMD_CACHE
+#define	CONFIG_CMD_DHCP
 #define	CONFIG_CMD_EXT2
 #define	CONFIG_CMD_FAT
 #define	CONFIG_CMD_GPIO
 #define	CONFIG_CMD_LED
 #define	CONFIG_CMD_MMC
+#define	CONFIG_CMD_NET
 #define	CONFIG_CMD_USB
 
 /*
@@ -148,6 +150,12 @@
 #define	CONFIG_USB_STORAGE
 #endif
 
+/* Ethernet */
+#ifdef	CONFIG_CMD_NET
+#define	CONFIG_USB_HOST_ETHER
+#define	CONFIG_USB_ETHER_SMSC95XX
+#endif
+
 /*
  * Boot Linux
  */
@@ -173,6 +181,7 @@
 /*
  * Extra Environments
  */
+
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"update_sd_firmware_filename=u-boot.sd\0" \
 	"update_sd_firmware="		/* Update the SD firmware partition */ \
@@ -189,6 +198,7 @@
 	"fdt_file=imx23-olinuxino.dtb\0" \
 	"fdt_addr=0x41000000\0" \
 	"boot_fdt=try\0" \
+	"ip_dyn=yes\0" \
 	"mmcdev=0\0" \
 	"mmcpart=2\0" \
 	"mmcroot=/dev/mmcblk0p3 rw rootwait\0" \
@@ -214,6 +224,31 @@
 			"fi; " \
 		"else " \
 			"bootm; " \
+		"fi;\0" \
+	"netargs=setenv bootargs console=${console_mainline},${baudrate} " \
+		"root=/dev/nfs " \
+		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+	"netboot=echo Booting from net ...; " \
+		"usb start; " \
+		"run netargs; "	\
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"${get_cmd} ${uimage}; " \
+		"if test ${boot_fdt} = yes; then " \
+			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+				"bootm ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"if test ${boot_fdt} = try; then " \
+					"bootm; " \
+				"else " \
+					"echo WARN: Cannot load the DT; " \
+				"fi;" \
+			"fi; " \
+		"else " \
+			"bootm; " \
 		"fi;\0"
 
 #define CONFIG_BOOTCOMMAND \
@@ -223,10 +258,9 @@
 		"else " \
 			"if run loaduimage; then " \
 				"run mmcboot; " \
-			"else " \
-				"echo ERR: Fail to boot from MMC; " \
+			"else run netboot; " \
 			"fi; " \
 		"fi; " \
-	"else exit; fi"
+	"else run netboot; fi"
 
 #endif /* __MX23_OLINUXINO_CONFIG_H__ */
-- 
1.8.1