[U-Boot] [PATCH v3 01/17] sf: Add bank address register writing support

[Jagannadha Sutradharudu Teki]

This patch provides support to program a flash bank address
register.

extended/bank address register contains an information to access
the 4th byte addressing in 3-byte address mode.

Currently added an bank address register writing support for
spansion flashes.

reff' the spec for more details about bank addr register
in Page-63, Table 8.16
http://www.spansion.com/Support/Datasheets/S25FL128S_256S_00.pdf

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna at xilinx.com>
---
Changes for v3:
	- none
Changes for v2:
	- none

 drivers/mtd/spi/spi_flash.c          | 37 ++++++++++++++++++++++++++++++++++++
 drivers/mtd/spi/spi_flash_internal.h |  6 ++++++
 include/spi_flash.h                  |  2 ++
 3 files changed, 45 insertions(+)

diff --git a/drivers/mtd/spi/spi_flash.c b/drivers/mtd/spi/spi_flash.c
index 0e38f59..7aba520 100644
--- a/drivers/mtd/spi/spi_flash.c
+++ b/drivers/mtd/spi/spi_flash.c
@@ -278,6 +278,40 @@ int spi_flash_cmd_write_status(struct spi_flash *flash, u8 sr)
 	return 0;
 }
 
+int spi_flash_cmd_bankaddr_write(struct spi_flash *flash, u8 bank_sel)
+{
+	u8 cmd, idcode0;
+	int ret;
+
+	idcode0 = flash->idcode0;
+	if (idcode0 == 0x01) {
+		cmd = CMD_BANKADDR_BRWR;
+	} else {
+		printf("SF: Unsupported bank addr write %02x\n", idcode0);
+		return -1;
+	}
+
+	ret = spi_flash_cmd_write_enable(flash);
+	if (ret < 0) {
+		debug("SF: enabling write failed\n");
+		return ret;
+	}
+
+	ret = spi_flash_cmd_write(flash->spi, &cmd, 1, &bank_sel, 1);
+	if (ret) {
+		debug("SF: fail to write bank addr register\n");
+		return ret;
+	}
+
+	ret = spi_flash_cmd_wait_ready(flash, SPI_FLASH_PROG_TIMEOUT);
+	if (ret < 0) {
+		debug("SF: write bank addr register timed out\n");
+		return ret;
+	}
+
+	return 0;
+}
+
 #ifdef CONFIG_OF_CONTROL
 int spi_flash_decode_fdt(const void *blob, struct spi_flash *flash)
 {
@@ -422,6 +456,9 @@ struct spi_flash *spi_flash_probe(unsigned int bus, unsigned int cs,
 		goto err_manufacturer_probe;
 	}
 
+	/* store the manuf id, for performing specific flash ops */
+	flash->idcode0 = *idp;
+
 #ifdef CONFIG_OF_CONTROL
 	if (spi_flash_decode_fdt(gd->fdt_blob, flash)) {
 		debug("SF: FDT decode error\n");
diff --git a/drivers/mtd/spi/spi_flash_internal.h b/drivers/mtd/spi/spi_flash_internal.h
index 141cfa8..6e38494 100644
--- a/drivers/mtd/spi/spi_flash_internal.h
+++ b/drivers/mtd/spi/spi_flash_internal.h
@@ -28,6 +28,9 @@
 #define CMD_ERASE_64K			0xd8
 #define CMD_ERASE_CHIP			0xc7
 
+/* Bank addr acess commands */
+#define CMD_BANKADDR_BRWR		0x17
+
 /* Common status */
 #define STATUS_WIP			0x01
 
@@ -77,6 +80,9 @@ static inline int spi_flash_cmd_write_disable(struct spi_flash *flash)
 /* Program the status register. */
 int spi_flash_cmd_write_status(struct spi_flash *flash, u8 sr);
 
+/* Program the bank address register */
+int spi_flash_cmd_bankaddr_write(struct spi_flash *flash, u8 bank_sel);
+
 /*
  * Same as spi_flash_cmd_read() except it also claims/releases the SPI
  * bus. Used as common part of the ->read() operation.
diff --git a/include/spi_flash.h b/include/spi_flash.h
index 3b6a44e..5ea42e1 100644
--- a/include/spi_flash.h
+++ b/include/spi_flash.h
@@ -38,6 +38,8 @@ struct spi_flash {
 	u32		page_size;
 	/* Erase (sector) size */
 	u32		sector_size;
+	/* ID code0 */
+	u8              idcode0;
 
 	void *memory_map;	/* Address of read-only SPI flash access */
 	int		(*read)(struct spi_flash *flash, u32 offset,
-- 
1.8.3