[U-Boot] [PATCH 1/1] am33xx: add CONFIG_SYS_NAND_DEVICE_WIDTH to determine NAND device bus-width
Pekon Gupta
pekon at ti.com
Wed Sep 25 07:23:58 CEST 2013
NAND driver needs to know bus-width of the connected NAND device, in order to
perform proper I/O and initialize itself. Currently there is no CONFIG option
to provide this information to NAND driver.
- SPL NAND driver does not have framework to parse ONFI parameter page.
- NAND drivers which cannot self initialize !defined(CONFIG_SYS_NAND_SELF_INIT)
do not have any information about device bus-width during board_nand_init(),
So, any device-width specific configurations are not possible there.
- There should be some mechanism to pass device bus-width information for
non-ONFI compliant devices.
This patch
(1) adds CONFIG_SYS_NAND_DEVICE_WIDTH which can take following value
16: NAND device with x16 bus-width
8: NAND device with x8 bus-width
(2) removes GPMC_NAND_ECC_LP_x16_LAYOUT, as NAND layout is determined based on
ecc-scheme and oobsize during initialization in board_nand_init(). Thus
this config is redundant.
Signed-off-by: Pekon Gupta <pekon at ti.com>
---
doc/README.nand | 9 +++++++++
drivers/mtd/nand/omap_gpmc.c | 18 +++++++++++-------
include/configs/am335x_evm.h | 2 +-
include/configs/am3517_crane.h | 2 +-
include/configs/am3517_evm.h | 2 +-
include/configs/cm_t35.h | 2 --
include/configs/devkit8000.h | 3 +--
include/configs/dig297.h | 2 --
include/configs/igep0033.h | 8 ++++----
include/configs/igep00x0.h | 2 +-
include/configs/mcx.h | 2 +-
include/configs/omap3_beagle.h | 3 +--
include/configs/omap3_evm_common.h | 1 -
include/configs/omap3_logic.h | 1 -
include/configs/omap3_overo.h | 3 +--
include/configs/omap3_pandora.h | 2 --
include/configs/omap3_zoom1.h | 2 --
include/configs/omap3_zoom2.h | 1 -
include/configs/siemens-am33x-common.h | 8 ++++----
include/configs/tam3517-common.h | 2 +-
include/configs/tricorder.h | 3 +--
21 files changed, 38 insertions(+), 40 deletions(-)
diff --git a/doc/README.nand b/doc/README.nand
index f9c921e..5726ff2 100644
--- a/doc/README.nand
+++ b/doc/README.nand
@@ -179,6 +179,15 @@ Configuration Options:
This is used by SoC platforms which do not have built-in ELM
hardware engine required for BCH ECC correction.
+ CONFIG_SYS_NAND_DEVICE_WIDTH
+ Specifies bus-width of the default NAND device connected to SoC.
+ This config is useful for driver which cannot self initialize or
+ parse ONFI parameter (like SPL drivers), or for supporting non-ONFI
+ compliant devices.
+ This config can take following values:
+ - 8: NAND devices has bus-width=x8
+ - 16: NAND device has bus-width=x16
+
Platform specific options
=========================
diff --git a/drivers/mtd/nand/omap_gpmc.c b/drivers/mtd/nand/omap_gpmc.c
index 68786f9..584e33e 100644
--- a/drivers/mtd/nand/omap_gpmc.c
+++ b/drivers/mtd/nand/omap_gpmc.c
@@ -214,11 +214,7 @@ static void omap_enable_hwecc(struct mtd_info *mtd, int32_t mode)
unsigned int eccsize1 = 0x00, eccsize0 = 0x00, bch_wrapmode = 0x00;
u32 ecc_size_config_val = 0;
u32 ecc_config_val = 0;
- u32 cs_config1_val;
- /* reconfigure GPMC device-width */
- cs_config1_val = readl(&gpmc_cfg->cs[cs].config1);
- writel((cs_config1_val | dev_width << 12), &gpmc_cfg->cs[cs].config1);
/* configure GPMC for specific ecc-scheme */
switch (bch->ecc_scheme) {
case OMAP_ECC_HAM1_CODE_SW:
@@ -772,10 +768,10 @@ int board_nand_init(struct nand_chip *nand)
nand->priv = &bch_priv;
nand->cmd_ctrl = omap_nand_hwcontrol;
nand->options |= NAND_NO_PADDING | NAND_CACHEPRG;
- /* If we are 16 bit dev, our gpmc config tells us that */
- if ((readl(&gpmc_cfg->cs[cs].config1) & 0x3000) == 0x1000)
+ if (CONFIG_SYS_NAND_DEVICE_WIDTH == 16)
nand->options |= NAND_BUSWIDTH_16;
-
+ else
+ nand->options &= ~NAND_BUSWIDTH_16;
nand->chip_delay = 100;
nand->ecc.layout = &omap_ecclayout;
@@ -795,5 +791,13 @@ int board_nand_init(struct nand_chip *nand)
nand->dev_ready = omap_spl_dev_ready;
#endif
+ /* reconfigure GPMC.CONFIG1 register with correct device-width */
+ gpmc_config = readl(&gpmc_cfg->cs[cs].config1);
+ if (nand->options & NAND_BUSWIDTH_16)
+ gpmc_config |= (0x1 << 12);
+ else
+ gpmc_config &= ~(0x1 << 12);
+ writel(gpmc_config, &gpmc_cfg->cs[cs].config1);
+
return 0;
}
diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h
index 978bca7..c92cb2f 100644
--- a/include/configs/am335x_evm.h
+++ b/include/configs/am335x_evm.h
@@ -216,6 +216,7 @@
#ifdef CONFIG_NAND
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_BLOCK_SIZE 131072
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
@@ -366,7 +367,6 @@
/* NAND support */
#ifdef CONFIG_NAND
#define CONFIG_CMD_NAND
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#if !defined(CONFIG_SPI_BOOT) && !defined(CONFIG_NOR_BOOT)
#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:128k(SPL)," \
diff --git a/include/configs/am3517_crane.h b/include/configs/am3517_crane.h
index 1fd2508..0985221 100644
--- a/include/configs/am3517_crane.h
+++ b/include/configs/am3517_crane.h
@@ -269,7 +269,6 @@
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_ENV_IS_IN_NAND 1
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
@@ -332,6 +331,7 @@
/* NAND boot config */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
diff --git a/include/configs/am3517_evm.h b/include/configs/am3517_evm.h
index 6500878..8593d44 100644
--- a/include/configs/am3517_evm.h
+++ b/include/configs/am3517_evm.h
@@ -263,7 +263,6 @@
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_ENV_IS_IN_NAND 1
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
@@ -326,6 +325,7 @@
/* NAND boot config */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h
index bc5b66c..1e3dd0d 100644
--- a/include/configs/cm_t35.h
+++ b/include/configs/cm_t35.h
@@ -164,8 +164,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x8_LAYOUT
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
/* Environment information */
diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h
index cb79b4e..d6c64a3 100644
--- a/include/configs/devkit8000.h
+++ b/include/configs/devkit8000.h
@@ -116,8 +116,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
#define CONFIG_JFFS2_NAND
@@ -318,6 +316,7 @@
/* NAND boot config */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
diff --git a/include/configs/dig297.h b/include/configs/dig297.h
index 30e3908..f69bcec 100644
--- a/include/configs/dig297.h
+++ b/include/configs/dig297.h
@@ -143,8 +143,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
#if defined(CONFIG_CMD_NET)
diff --git a/include/configs/igep0033.h b/include/configs/igep0033.h
index 3e18a65..ce6b9be 100644
--- a/include/configs/igep0033.h
+++ b/include/configs/igep0033.h
@@ -188,7 +188,6 @@
/* NAND support */
#define CONFIG_NAND
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_SYS_NAND_BASE (0x08000000) /* phys address CS0 */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_ONFI_DETECTION 1
@@ -248,11 +247,12 @@
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_ECC
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
- CONFIG_SYS_NAND_PAGE_SIZE)
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
+#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
+ CONFIG_SYS_NAND_PAGE_SIZE)
#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
10, 11, 12, 13, 14, 15, 16, 17, \
diff --git a/include/configs/igep00x0.h b/include/configs/igep00x0.h
index 9982cf6..7e5bc9b 100644
--- a/include/configs/igep00x0.h
+++ b/include/configs/igep00x0.h
@@ -268,7 +268,6 @@
#define PISMO1_NAND_SIZE GPMC_SIZE_128M /* Configure the PISMO */
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_SYS_NAND_BASE NAND_BASE
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_ENV_OFFSET 0x260000 /* environment starts here */
#define CONFIG_ENV_IS_IN_NAND 1
#define CONFIG_ENV_SIZE (512 << 10) /* Total Size Environment */
@@ -354,6 +353,7 @@
/* NAND boot config */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
diff --git a/include/configs/mcx.h b/include/configs/mcx.h
index 5e27ab2..d508978 100644
--- a/include/configs/mcx.h
+++ b/include/configs/mcx.h
@@ -322,7 +322,6 @@
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
#define CONFIG_ENV_IS_IN_NAND
#define SMNAND_ENV_OFFSET 0x180000 /* environment starts here */
@@ -385,6 +384,7 @@
#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
/* NAND boot config */
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index c1245e7..9050f55 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -184,8 +184,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
@@ -424,6 +422,7 @@
/* NAND boot config */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
diff --git a/include/configs/omap3_evm_common.h b/include/configs/omap3_evm_common.h
index edf6543..564af9a 100644
--- a/include/configs/omap3_evm_common.h
+++ b/include/configs/omap3_evm_common.h
@@ -210,7 +210,6 @@
#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#elif defined(CONFIG_CMD_ONENAND)
#define CONFIG_SYS_FLASH_BASE PISMO1_ONEN_BASE
diff --git a/include/configs/omap3_logic.h b/include/configs/omap3_logic.h
index ee6db51..e198c4c 100644
--- a/include/configs/omap3_logic.h
+++ b/include/configs/omap3_logic.h
@@ -298,7 +298,6 @@
#if defined(CONFIG_CMD_NAND)
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#endif
diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h
index 88380a4..de06e20 100644
--- a/include/configs/omap3_overo.h
+++ b/include/configs/omap3_overo.h
@@ -120,8 +120,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand */
/* at CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
#define CONFIG_JFFS2_NAND
@@ -317,6 +315,7 @@
/* NAND boot config */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
diff --git a/include/configs/omap3_pandora.h b/include/configs/omap3_pandora.h
index 91a2568..6ea106d 100644
--- a/include/configs/omap3_pandora.h
+++ b/include/configs/omap3_pandora.h
@@ -131,8 +131,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand */
/* at CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h
index c747d52..1dd7b9c 100644
--- a/include/configs/omap3_zoom1.h
+++ b/include/configs/omap3_zoom1.h
@@ -138,8 +138,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
#define CONFIG_JFFS2_NAND
diff --git a/include/configs/omap3_zoom2.h b/include/configs/omap3_zoom2.h
index cb8c7ec..9ca7fbe 100644
--- a/include/configs/omap3_zoom2.h
+++ b/include/configs/omap3_zoom2.h
@@ -158,7 +158,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_SYS_MAX_NAND_DEVICE 1
/* Environment information */
diff --git a/include/configs/siemens-am33x-common.h b/include/configs/siemens-am33x-common.h
index 5426ee8..197accc 100644
--- a/include/configs/siemens-am33x-common.h
+++ b/include/configs/siemens-am33x-common.h
@@ -182,11 +182,12 @@
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_ECC
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
- CONFIG_SYS_NAND_PAGE_SIZE)
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
+#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
+ CONFIG_SYS_NAND_PAGE_SIZE)
#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
10, 11, 12, 13, 14, 15, 16, 17, \
@@ -433,7 +434,6 @@
"\0"
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_SYS_NAND_BASE (0x08000000) /* physical address */
/* to access nand at */
/* CS0 */
diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h
index 60dd8ff..1f31a87 100644
--- a/include/configs/tam3517-common.h
+++ b/include/configs/tam3517-common.h
@@ -188,7 +188,6 @@
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
#define CONFIG_ENV_IS_IN_NAND
#define SMNAND_ENV_OFFSET 0x180000 /* environment starts here */
@@ -252,6 +251,7 @@
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
/* NAND boot config */
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
diff --git a/include/configs/tricorder.h b/include/configs/tricorder.h
index 6daea50..95bbbaa 100644
--- a/include/configs/tricorder.h
+++ b/include/configs/tricorder.h
@@ -106,8 +106,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
#define CONFIG_BCH
@@ -284,6 +282,7 @@
/* NAND boot config */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
--
1.8.1
More information about the U-Boot
mailing list