[U-Boot] [PATCH] mmc: Handle switch error status bit in MMC card status

Gabbasov, Andrew Andrew_Gabbasov at mentor.com
Thu Apr 3 11:32:10 CEST 2014


Hi Pantelis,

> From: Pantelis Antoniou [panto at antoniou-consulting.com]
> Sent: Wednesday, April 02, 2014 14:14
> To: Gabbasov, Andrew
> Cc: u-boot at lists.denx.de
> Subject: Re: [U-Boot] [PATCH] mmc: Handle switch error status bit in MMC card status
> 
> Hi Andrew,
> 
> In general looks good; only a small nag.
> 
> On Mar 24, 2014, at 9:39 AM, Andrew Gabbasov wrote:
> 
> > MMC switch command for unsupported feature (e.g. bus width) sets a switch
> > error bit in card status. This bit should be checked, and, if it's set,
> > no access with new controller settings should be performed.
> >
> > Signed-off-by: Andrew Gabbasov <andrew_gabbasov at mentor.com>
> > ---
> > drivers/mmc/mmc.c |    4 +++-
> > include/mmc.h     |    2 ++
> > 2 files changed, 5 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/mmc/mmc.c b/drivers/mmc/mmc.c
> > index 8ab0bc9..16105bc 100644
> > --- a/drivers/mmc/mmc.c
> > +++ b/drivers/mmc/mmc.c
> > @@ -155,6 +155,8 @@ int mmc_send_status(struct mmc *mmc, int timeout)
> > #endif
> >               return TIMEOUT;
> >       }
> > +     if (cmd.response[0] & MMC_STATUS_SWITCH_ERROR)
> > +             return SWITCH_ERR;
> >
> >       return 0;
> > }
> > @@ -505,7 +507,7 @@ static int mmc_change_freq(struct mmc *mmc)
> >       err = mmc_switch(mmc, EXT_CSD_CMD_SET_NORMAL, EXT_CSD_HS_TIMING, 1);
> >
> >       if (err)
> > -             return err;
> > +             return ((err == SWITCH_ERR) ? 0 : err);
> >
> 
> Change to:
> 
>         return err == SWITCH_ERR ? 0 : err;
> 
> No need for parentheses.

Thank you for the review.
I'm sending a v2 patch with his change and also re-based to current master head.

Thanks!

Best regards,
Andrew

> 
> >       /* Now check to see that it worked */
> >       err = mmc_send_ext_csd(mmc, ext_csd);
> > diff --git a/include/mmc.h b/include/mmc.h
> > index e95a237..d5833f8 100644
> > --- a/include/mmc.h
> > +++ b/include/mmc.h
> > @@ -53,6 +53,7 @@
> > #define COMM_ERR              -18 /* Communications Error */
> > #define TIMEOUT                       -19
> > #define IN_PROGRESS           -20 /* operation is in progress */
> > +#define SWITCH_ERR           -21 /* Card reports failure to switch mode */
> >
> > #define MMC_CMD_GO_IDLE_STATE         0
> > #define MMC_CMD_SEND_OP_COND          1
> > @@ -108,6 +109,7 @@
> > #define SECURE_ERASE          0x80000000
> >
> > #define MMC_STATUS_MASK               (~0x0206BF7F)
> > +#define MMC_STATUS_SWITCH_ERROR      (1 << 7)
> > #define MMC_STATUS_RDY_FOR_DATA (1 << 8)
> > #define MMC_STATUS_CURR_STATE (0xf << 9)
> > #define MMC_STATUS_ERROR      (1 << 19)
> > --
> > 1.7.10.4
> 
> Regards
> 
> -- Pantelis
> 


More information about the U-Boot mailing list