[U-Boot] [PATCH v6] spi: pl022_spi: Add support for ARM PL022 spi controller
Armando Visconti
armando.visconti at st.com
Wed Jan 8 10:19:47 CET 2014
Hello Jagan,
Sorry for late reply.
On 12/20/2013 8:03 PM, Jagan Teki wrote:
> On Fri, Oct 4, 2013 at 12:20 PM, Jagan Teki <jagannadh.teki at gmail.com> wrote:
>> Hi Vipin,
>>
>> I have few quick comments, please fix it.
>> Please use the u-boot-spi.git with master-probe branch for testing this driver.
>> Let me know for any issues/concerns.
>>
>> On Wed, Jun 12, 2013 at 7:55 PM, Jagan Teki <jagannadh.teki at gmail.com> wrote:
>>> Thanks for v6 sent.
>>>
>>> Have you tested this?
>>> on which board, include/configs/*.h file?
>>>
>>> --
>>> Thanks,
>>> Jagan.
>>>
>>> On Wed, Jun 12, 2013 at 6:17 PM, Armando Visconti
>>> <armando.visconti at st.com> wrote:
>>>> This patch adds the support for the ARM PL022 SPI controller for the standard
>>>> variant (0x00041022), which has a 16bit wide and 8 locations deep TX/RX FIFO.
>>>>
>>>> Signed-off-by: Armando Visconti <armando.visconti at st.com>
>>>> Signed-off-by: Vipin Kumar <vipin.kumar at st.com>
>>>> Acked-by: Stefan Roese <sr at denx.de>
>>>> ---
>>>> v5->v6
>>>>
>>>> 1. Make use of spi_alloc_slave() macro.
>>>> 2. Changed the identation on 'if statement' as requested
>>>> by Jagan.
>>>>
>>>> drivers/spi/Makefile | 1 +
>>>> drivers/spi/pl022_spi.c | 308 ++++++++++++++++++++++++++++++++++++++++++++++++
>>>> 2 files changed, 309 insertions(+)
>>>> create mode 100644 drivers/spi/pl022_spi.c
>>>>
>>>> diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
>>>> index d08609e..b6443b1 100644
>>>> --- a/drivers/spi/Makefile
>>>> +++ b/drivers/spi/Makefile
>>>> @@ -47,6 +47,7 @@ COBJS-$(CONFIG_MXC_SPI) += mxc_spi.o
>>>> COBJS-$(CONFIG_MXS_SPI) += mxs_spi.o
>>>> COBJS-$(CONFIG_OC_TINY_SPI) += oc_tiny_spi.o
>>>> COBJS-$(CONFIG_OMAP3_SPI) += omap3_spi.o
>>>> +COBJS-$(CONFIG_PL022_SPI) += pl022_spi.o
>>>> COBJS-$(CONFIG_SOFT_SPI) += soft_spi.o
>>>> COBJS-$(CONFIG_SH_SPI) += sh_spi.o
>>>> COBJS-$(CONFIG_FSL_ESPI) += fsl_espi.o
>>>> diff --git a/drivers/spi/pl022_spi.c b/drivers/spi/pl022_spi.c
>>>> new file mode 100644
>>>> index 0000000..5b47413
>>>> --- /dev/null
>>>> +++ b/drivers/spi/pl022_spi.c
>>>> @@ -0,0 +1,308 @@
>>>> +/*
>>>> + * (C) Copyright 2012
>>>> + * Armando Visconti, ST Microelectronics, armando.visconti at st.com.
>>>> + *
>>>> + * Driver for ARM PL022 SPI Controller. Based on atmel_spi.c
>>>> + * by Atmel Corporation.
>>>> + *
>>>> + * This program is free software; you can redistribute it and/or
>>>> + * modify it under the terms of the GNU General Public License as
>>>> + * published by the Free Software Foundation; either version 2 of
>>>> + * the License, or (at your option) any later version.
>>>> + *
>>>> + * This program is distributed in the hope that it will be useful,
>>>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>>>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>>>> + * GNU General Public License for more details.
>>>> + *
>>>> + * You should have received a copy of the GNU General Public License
>>>> + * along with this program; if not, write to the Free Software
>>>> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
>>>> + * MA 02111-1307 USA
>>>> + */
>> Use latest SPDX-License-Identifier:
>> check for any existing one.
>>
>>>> +
>>>> +#include <common.h>
>>>> +#include <malloc.h>
>>>> +#include <spi.h>
>>>> +#include <asm/io.h>
>>>> +#include <asm/arch/hardware.h>
>>>> +
>>>> +/* SSP registers mapping */
>>>> +struct pl022 {
>> Something like pl022_spi_regs
>>
>>>> + u32 ssp_cr0; /* 0x000 */
>>>> + u32 ssp_cr1; /* 0x004 */
>>>> + u32 ssp_dr; /* 0x008 */
>>>> + u32 ssp_sr; /* 0x00c */
>>>> + u32 ssp_cpsr; /* 0x010 */
>>>> + u32 ssp_imsc; /* 0x014 */
>>>> + u32 ssp_ris; /* 0x018 */
>>>> + u32 ssp_mis; /* 0x01c */
>>>> + u32 ssp_icr; /* 0x020 */
>>>> + u32 ssp_dmacr; /* 0x024 */
>>>> + u8 reserved_1[0x080 - 0x028];
>>>> + u32 ssp_itcr; /* 0x080 */
>>>> + u32 ssp_itip; /* 0x084 */
>>>> + u32 ssp_itop; /* 0x088 */
>>>> + u32 ssp_tdr; /* 0x08c */
>>>> + u8 reserved_2[0xFE0 - 0x090];
>>>> + u32 ssp_pid0; /* 0xfe0 */
>>>> + u32 ssp_pid1; /* 0xfe4 */
>>>> + u32 ssp_pid2; /* 0xfe8 */
>>>> + u32 ssp_pid3; /* 0xfec */
>>>> + u32 ssp_cid0; /* 0xff0 */
>>>> + u32 ssp_cid1; /* 0xff4 */
>>>> + u32 ssp_cid2; /* 0xff8 */
>>>> + u32 ssp_cid3; /* 0xffc */
>>>> +};
>>>> +
>> -- TAG+
>>>> +/* SSP Control Register 0 - SSP_CR0 */
>>>> +#define SSP_CR0_SPO (0x1 << 6)
>>>> +#define SSP_CR0_SPH (0x1 << 7)
>>>> +#define SSP_CR0_8BIT_MODE (0x07)
>>>> +#define SSP_SCR_MAX (0xFF)
>>>> +#define SSP_SCR_SHFT 8
>>>> +
>>>> +/* SSP Control Register 0 - SSP_CR1 */
>>>> +#define SSP_CR1_MASK_SSE (0x1 << 1)
>>>> +
>>>> +#define SSP_CPSR_MAX (0xFE)
>>>> +
>>>> +/* SSP Status Register - SSP_SR */
>>>> +#define SSP_SR_MASK_TFE (0x1 << 0) /* Transmit FIFO empty */
>>>> +#define SSP_SR_MASK_TNF (0x1 << 1) /* Transmit FIFO not full */
>>>> +#define SSP_SR_MASK_RNE (0x1 << 2) /* Receive FIFO not empty */
>>>> +#define SSP_SR_MASK_RFF (0x1 << 3) /* Receive FIFO full */
>>>> +#define SSP_SR_MASK_BSY (0x1 << 4) /* Busy Flag */
>>>> +
>> --- TAG -
>>
>> Bit mask macros - please place after headers.
>> We follow a simple format to write spi driver - please check
>> http://patchwork.ozlabs.org/patch/265683/
>>
>> And try to verify your code w.r.t above format - let me know any comments.
>>
>>>> +struct pl022_spi_slave {
>>>> + struct spi_slave slave;
>>>> + void *regs;
>> Please use the structure pointer instead of void.
>>
>>>> + unsigned int freq;
>>>> +};
>>>> +
>>>> +static inline struct pl022_spi_slave *to_pl022_spi(struct spi_slave *slave)
>>>> +{
>>>> + return container_of(slave, struct pl022_spi_slave, slave);
>>>> +}
>>>> +
>>>> +/*
>>>> + * Following three functions should be provided by the
>>>> + * board support package.
>>>> + */
>>>> +int __weak spi_cs_is_valid(unsigned int bus, unsigned int cs)
>>>> +{
>>>> + return 1;
>>>> +}
>>>> +
>>>> +void __weak spi_cs_activate(struct spi_slave *slave)
>>>> +{
>>>> + /* do nothing */
>>>> +}
>>>> +
>>>> +void __weak spi_cs_deactivate(struct spi_slave *slave)
>>>> +{
>>>> + /* do nothing */
>>>> +}
>>>> +
>>>> +void spi_init(void)
>>>> +{
>>>> + /* do nothing */
>>>> +}
>>>> +
>>>> +/*
>>>> + * ARM PL022 exists in different 'flavors'.
>>>> + * This drivers currently support the standard variant (0x00041022), that has a
>>>> + * 16bit wide and 8 locations deep TX/RX FIFO.
>>>> + */
>>>> +static int pl022_is_supported(struct pl022_spi_slave *ps)
>>>> +{
>>>> + struct pl022 *pl022 = (struct pl022 *)ps->regs;
>>>> +
>>>> + /* PL022 version is 0x00041022 */
>>>> + if ((readl(&pl022->ssp_pid0) == 0x22) &&
>>>> + (readl(&pl022->ssp_pid1) == 0x10) &&
>>>> + ((readl(&pl022->ssp_pid2) & 0xf) == 0x04) &&
>>>> + (readl(&pl022->ssp_pid3) == 0x00))
>>>> + return 1;
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
>>>> + unsigned int max_hz, unsigned int mode)
>>>> +{
>>>> + struct pl022_spi_slave *ps;
>>>> + struct pl022 *pl022;
>>>> + u16 scr = 1, prescaler, cr0 = 0, cpsr = 0;
>>>> +
>>>> + if (!spi_cs_is_valid(bus, cs))
>>>> + return NULL;
>>>> +
>>>> + ps = spi_alloc_slave(struct pl022_spi_slave, bus, cs);
>>>> + if (!ps)
>>>> + return NULL;
>>>> +
>>>> + ps->freq = max_hz;
>>>> +
>>>> + switch (bus) {
>>>> + case 0:
>>>> + ps->regs = (void *)CONFIG_SYS_SPI_BASE;
>>>> + break;
>>>> +#ifdef CONFIG_SYS_SPI_BASE1
>>>> + case 1:
>>>> + ps->regs = (void *)CONFIG_SYS_SPI_BASE1;
>>>> + break;
>>>> +#endif
>>>> +#ifdef CONFIG_SYS_SPI_BASE2
>>>> + case 2:
>>>> + ps->regs = (void *)CONFIG_SYS_SPI_BASE2;
>>>> + break;
>>>> +#endif
>>>> +#ifdef CONFIG_SYS_SPI_BASE3
>>>> + case 3:
>>>> + ps->regs = (void *)CONFIG_SYS_SPI_BASE3;
>>>> + break;
>>>> +#endif
>>>> + default:
>>>> + free(ps);
>>>> + return NULL;
>>>> + }
>>>> +
>>>> + pl022 = (struct pl022 *)ps->regs;
>>>> +
>>>> + /* Check the PL022 version */
>>>> + if (!pl022_is_supported(ps)) {
>>>> + free(ps);
>>>> + return NULL;
>>>> + }
>>>> +
>>>> + /* Set requested polarity and 8bit mode */
>>>> + cr0 = SSP_CR0_8BIT_MODE;
>>>> + cr0 |= (mode & SPI_CPHA) ? SSP_CR0_SPH : 0;
>>>> + cr0 |= (mode & SPI_CPOL) ? SSP_CR0_SPO : 0;
>>>> +
>>>> + writel(cr0, &pl022->ssp_cr0);
>>>> +
>>>> + /* Program the SSPClk frequency */
>>>> + prescaler = CONFIG_SYS_SPI_CLK / ps->freq;
>>>> +
>>>> + if (prescaler <= 0xFF) {
>>>> + cpsr = prescaler;
>>>> + } else {
>>>> + for (scr = 1; scr <= SSP_SCR_MAX; scr++) {
>>>> + if (!(prescaler % scr)) {
>>>> + cpsr = prescaler / scr;
>>>> + if (cpsr <= SSP_CPSR_MAX)
>>>> + break;
>>>> + }
>>>> + }
>>>> +
>>>> + if (scr > SSP_SCR_MAX) {
>>>> + scr = SSP_SCR_MAX;
>>>> + cpsr = prescaler / scr;
>>>> + cpsr &= SSP_CPSR_MAX;
>>>> + }
>>>> + }
>>>> +
>>>> + if (cpsr & 0x1)
>>>> + cpsr++;
>>>> +
>>>> + writel(cpsr, &pl022->ssp_cpsr);
>>>> + cr0 = readl(&pl022->ssp_cr0);
>>>> + writel(cr0 | (scr - 1) << SSP_SCR_SHFT, &pl022->ssp_cr0);
>>>> +
>>>> + return &ps->slave;
>>>> +}
>>>> +
>>>> +void spi_free_slave(struct spi_slave *slave)
>>>> +{
>>>> + struct pl022_spi_slave *ps = to_pl022_spi(slave);
>>>> +
>>>> + free(ps);
>>>> +}
>>>> +
>>>> +int spi_claim_bus(struct spi_slave *slave)
>>>> +{
>>>> + struct pl022_spi_slave *ps = to_pl022_spi(slave);
>>>> + struct pl022 *pl022 = (struct pl022 *)ps->regs;
>>>> +
>>>> + /* Enable the SPI hardware */
>>>> + setbits_le32(&pl022->ssp_cr1, SSP_CR1_MASK_SSE);
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +void spi_release_bus(struct spi_slave *slave)
>>>> +{
>>>> + struct pl022_spi_slave *ps = to_pl022_spi(slave);
>>>> + struct pl022 *pl022 = (struct pl022 *)ps->regs;
>>>> +
>>>> + /* Disable the SPI hardware */
>>>> + writel(0x0, &pl022->ssp_cr1);
>>>> +}
>>>> +
>>>> +int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
>>>> + const void *dout, void *din, unsigned long flags)
>>>> +{
>>>> + struct pl022_spi_slave *ps = to_pl022_spi(slave);
>>>> + struct pl022 *pl022 = (struct pl022 *)ps->regs;
>>>> + u32 len_tx = 0, len_rx = 0, len;
>>>> + u32 ret = 0;
>>>> + const u8 *txp = dout;
>>>> + u8 *rxp = din, value;
>>>> +
>>>> + if (bitlen == 0)
>>>> + /* Finish any previously submitted transfers */
>>>> + goto out;
>>>> +
>>>> + /*
>>>> + * TODO: The controller can do non-multiple-of-8 bit
>>>> + * transfers, but this driver currently doesn't support it.
>>>> + *
>>>> + * It's also not clear how such transfers are supposed to be
>>>> + * represented as a stream of bytes...this is a limitation of
>>>> + * the current SPI interface.
>>>> + */
>>>> + if (bitlen % 8) {
>>>> + ret = -1;
>>>> +
>>>> + /* Errors always terminate an ongoing transfer */
>>>> + flags |= SPI_XFER_END;
>>>> + goto out;
>>>> + }
>>>> +
>>>> + len = bitlen / 8;
>>>> +
>>>> + if (flags & SPI_XFER_BEGIN)
>>>> + spi_cs_activate(slave);
>>>> +
>>>> + while (len_tx < len) {
>>>> + if (readl(&pl022->ssp_sr) & SSP_SR_MASK_TNF) {
>>>> + value = (txp != NULL) ? *txp++ : 0;
>>>> + writel(value, &pl022->ssp_dr);
>>>> + len_tx++;
>>>> + }
>>>> +
>>>> + if (readl(&pl022->ssp_sr) & SSP_SR_MASK_RNE) {
>>>> + value = readl(&pl022->ssp_dr);
>>>> + if (rxp)
>>>> + *rxp++ = value;
>>>> + len_rx++;
>>>> + }
>>>> + }
>>>> +
>>>> + while (len_rx < len_tx) {
>>>> + if (readl(&pl022->ssp_sr) & SSP_SR_MASK_RNE) {
>>>> + value = readl(&pl022->ssp_dr);
>>>> + if (rxp)
>>>> + *rxp++ = value;
>>>> + len_rx++;
>>>> + }
>>>> + }
>>>> +
>>>> +out:
>>>> + if (flags & SPI_XFER_END)
>>>> + spi_cs_deactivate(slave);
>>>> +
>>>> + return ret;
>>>> +}
>>>> --
>>>> 1.7.11.7
> Ping
>
Unfortunately lot of changes happened to our organization
and we (myself and Vipin) are no longer able to proceed in doing
this job.
So I think we need to drop this patch, unless someone from the
u-boot community has the possibility to (and is willing to) proceed
in implementing and testing the proper changes.
Sorry for that,
Armando
--
-- "Every step appears to be the unavoidable consequence of the
-- preceding one." (A. Einstein)
--
Armando Visconti Mobile: (+39) 346 8879146
Senior SW Engineer Fax: (+39) 02 93519290
CPG Work: (+39) 02 93519683
Computer System Division e-mail: armando.visconti at st.com
ST Microelectronics TINA: 051 4683
More information about the U-Boot
mailing list