[U-Boot] [PATCH v2 3/9] kmp204x: I2C deblocking for I2C-bus1 added

[Valentin Longchamp]

From: Rainer Boschung <rainer.boschung at keymile.com>

-uses common deblocking algorithm from ../common/common.c
-supports deblocking of of  I2C-bus1 by means of QRIO GPIO
  - SCL1 = GPIO_A16
  - SDA1 = GPIO_A17

QRIO GPIOs act in an open-drain-like manner, for 0 GPIO drives
low and for 1 the GPIO is an input and must be pulled up externaly!

Signed-off-by: Rainer Boschung <rainer.boschung at keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp at keymile.com>
---

Changes in v2: None

 board/keymile/kmp204x/kmp204x.c     | 53 ++++++++++++++++++++++++++++++++++---
 include/configs/km/kmp204x-common.h | 10 +++++++
 2 files changed, 60 insertions(+), 3 deletions(-)

diff --git a/board/keymile/kmp204x/kmp204x.c b/board/keymile/kmp204x/kmp204x.c
index bbb2453..8d6eecb 100644
--- a/board/keymile/kmp204x/kmp204x.c
+++ b/board/keymile/kmp204x/kmp204x.c
@@ -33,12 +33,51 @@ int checkboard(void)
 	return 0;
 }
 
-/* TODO: implement the I2C deblocking function */
-int i2c_make_abort(void)
+/* I2C deblocking uses the algorithm defined in ../common/common.c, which
+ * makes use of 2 QRIO GPIOs to act on the SCL and SDA signals of an I2C bus.
+ * According to the standard I2C IOs must not drive HI-Levels, so the
+ * QRIO GPIOs are used in open-drain fashion:
+ *  -> 0 GPIO configured as output that drives low
+ *  -> 1 GPIO configured as input pull-up ties high
+ */
+
+/* GPIOs used for deblocking I2C bus 1 */
+#define DBLK_PORT1	GPIO_A
+#define DBLK_SCL1	16
+#define DBLK_SDA1	17
+
+/* By default deblock GPIOs are floating */
+static void i2c_deblock_gpio_cfg(void)
+{
+	/* set I2C bus 1 deblocking GPIOs input, but 0 value for open drain */
+	qrio_gpio_direction_input(DBLK_PORT1, DBLK_SCL1);
+	qrio_gpio_direction_input(DBLK_PORT1, DBLK_SDA1);
+
+	qrio_set_gpio(DBLK_PORT1, DBLK_SCL1, 0);
+	qrio_set_gpio(DBLK_PORT1, DBLK_SDA1, 0);
+}
+
+void set_sda(int state)
+{
+	qrio_set_opendrain_gpio(DBLK_PORT1, DBLK_SDA1, state);
+}
+
+void set_scl(int state)
+{
+	qrio_set_opendrain_gpio(DBLK_PORT1, DBLK_SCL1, state);
+}
+
+int get_sda(void)
+{
+	return qrio_get_gpio(DBLK_PORT1, DBLK_SDA1);
+}
+
+int get_scl(void)
 {
-	return 1;
+	return qrio_get_gpio(DBLK_PORT1, DBLK_SCL1);
 }
 
+
 #define ZL30158_RST	8
 #define ZL30343_RST	9
 
@@ -77,6 +116,14 @@ unsigned long get_board_sys_clk(unsigned long dummy)
 	return 66666666;
 }
 
+int misc_init_f(void)
+{
+	/* configure QRIO pis for i2c deblocking */
+	i2c_deblock_gpio_cfg();
+
+	return 0;
+}
+
 #define NUM_SRDS_BANKS	2
 #define PHY_RST		15
 
diff --git a/include/configs/km/kmp204x-common.h b/include/configs/km/kmp204x-common.h
index e33ac90..626879a 100644
--- a/include/configs/km/kmp204x-common.h
+++ b/include/configs/km/kmp204x-common.h
@@ -211,6 +211,7 @@ unsigned long get_board_sys_clk(unsigned long dummy);
 
 #define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
+#define CONFIG_MISC_INIT_F
 #define CONFIG_MISC_INIT_R
 #define CONFIG_LAST_STAGE_INIT
 
@@ -266,7 +267,10 @@ unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
 
 /* I2C */
+
 #define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_INIT_BOARD
+#define CONFIG_SYS_I2C_SPEED		100000 /* deblocking */
 #define CONFIG_SYS_NUM_I2C_BUSES	3
 #define CONFIG_SYS_I2C_MAX_HOPS		1
 #define CONFIG_SYS_I2C_FSL		/* Use FSL I2C driver */
@@ -279,6 +283,12 @@ unsigned long get_board_sys_clk(unsigned long dummy);
 					{0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \
 					{0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \
 				}
+#ifndef __ASSEMBLY__
+void set_sda(int state);
+void set_scl(int state);
+int get_sda(void);
+int get_scl(void);
+#endif
 
 #define CONFIG_KM_IVM_BUS		1	/* I2C1 (Mux-Port 1)*/
 
-- 
1.8.0.1