[U-Boot] [PATCH v1 6/7] board/ti/am43xx: add support for parallel NAND
Pekon Gupta
pekon at ti.com
Fri Jul 4 21:05:16 CEST 2014
This patch adds support for NAND device connected to GPMC chip-select on
following AM43xx EVM boards.
am437x-gp-evm: On this board, NAND Flash signals are muxed with eMMC, thus at a
time either eMMC or NAND can be enabled. Selection between eMMC and NAND is
controlled by:
(a) Statically using Jumper on connecter (J89) present on board.
(a) If Jumper on J89 is NOT used, then selection can be dynamically controlled
by driving SPI2_CS0[MUX_MODE=GPIO] pin via software:
SPI2_CS0 == 0: NAND (default)
SPI2_CS0 == 1: eMMC
am43x-epos-evm: On this board, NAND Flash control lines are muxed with QSPI,
Thus only one of the two can be used at a time. Selection is controlled by:
(a) Dynamically driving following GPIO pin from software
GPMC_A0(GPIO) == 0 NAND is selected (default)
NAND device (MT29F4G08AB) on these boards has:
- data-width=8bits
- blocksize=256KB
- pagesize=4KB
- oobsize=224 bytes
For above NAND device, ROM code expects the boot-loader to be flashed in BCH16
ECC scheme for NAND boot, So by default BCH16 ECC is enabled for AM43xx EVMs.
Signed-off-by: Pekon Gupta <pekon at ti.com>
---
board/ti/am43xx/board.c | 1 +
board/ti/am43xx/mux.c | 42 ++++++++++++++++++++++++++
boards.cfg | 2 +-
include/configs/am43xx_evm.h | 70 ++++++++++++++++++++++++++++++++++++++++++++
4 files changed, 114 insertions(+), 1 deletion(-)
diff --git a/board/ti/am43xx/board.c b/board/ti/am43xx/board.c
index 054a452..2c3a290 100644
--- a/board/ti/am43xx/board.c
+++ b/board/ti/am43xx/board.c
@@ -487,6 +487,7 @@ void sdram_init(void)
int board_init(void)
{
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+ gpmc_init();
return 0;
}
diff --git a/board/ti/am43xx/mux.c b/board/ti/am43xx/mux.c
index 50967e1..172adcd 100644
--- a/board/ti/am43xx/mux.c
+++ b/board/ti/am43xx/mux.c
@@ -73,6 +73,36 @@ static struct module_pin_mux gpio5_7_pin_mux[] = {
{-1},
};
+#ifdef CONFIG_NAND
+static struct module_pin_mux nand_pin_mux[] = {
+ {OFFSET(gpmc_ad0), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD0 */
+ {OFFSET(gpmc_ad1), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD1 */
+ {OFFSET(gpmc_ad2), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD2 */
+ {OFFSET(gpmc_ad3), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD3 */
+ {OFFSET(gpmc_ad4), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD4 */
+ {OFFSET(gpmc_ad5), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD5 */
+ {OFFSET(gpmc_ad6), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD6 */
+ {OFFSET(gpmc_ad7), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD7 */
+#ifdef CONFIG_SYS_NAND_BUSWIDTH_16BIT
+ {OFFSET(gpmc_ad8), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD8 */
+ {OFFSET(gpmc_ad9), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD9 */
+ {OFFSET(gpmc_ad10), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD10 */
+ {OFFSET(gpmc_ad11), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD11 */
+ {OFFSET(gpmc_ad12), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD12 */
+ {OFFSET(gpmc_ad13), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD13 */
+ {OFFSET(gpmc_ad14), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD14 */
+ {OFFSET(gpmc_ad15), (MODE(0) | PULLUDDIS | RXACTIVE)}, /* AD15 */
+#endif
+ {OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* Wait */
+ {OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN)}, /* Write Protect */
+ {OFFSET(gpmc_csn0), (MODE(0) | PULLUP_EN)}, /* Chip-Select */
+ {OFFSET(gpmc_wen), (MODE(0) | PULLDOWN_EN)}, /* Write Enable */
+ {OFFSET(gpmc_oen_ren), (MODE(0) | PULLDOWN_EN)}, /* Read Enable */
+ {OFFSET(gpmc_advn_ale), (MODE(0) | PULLDOWN_EN)}, /* Addr Latch Enable*/
+ {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLDOWN_EN)}, /* Byte Enable */
+ {-1},
+};
+#else
static struct module_pin_mux qspi_pin_mux[] = {
{OFFSET(gpmc_csn0), (MODE(3) | PULLUP_EN | RXACTIVE)}, /* QSPI_CS0 */
{OFFSET(gpmc_csn3), (MODE(2) | PULLUP_EN | RXACTIVE)}, /* QSPI_CLK */
@@ -82,6 +112,7 @@ static struct module_pin_mux qspi_pin_mux[] = {
{OFFSET(gpmc_be0n_cle), (MODE(3) | PULLUP_EN | RXACTIVE)}, /* QSPI_D3 */
{-1},
};
+#endif
void enable_uart0_pin_mux(void)
{
@@ -97,12 +128,23 @@ void enable_board_pin_mux(void)
if (board_is_gpevm()) {
configure_module_pin_mux(gpio5_7_pin_mux);
configure_module_pin_mux(rgmii1_pin_mux);
+#if defined(CONFIG_NAND)
+ configure_module_pin_mux(nand_pin_mux);
+#endif
} else if (board_is_sk()) {
configure_module_pin_mux(rgmii1_pin_mux);
+#if defined(CONFIG_NAND)
+ pr_err("NAND flash is not present on this board\n");
+#else
configure_module_pin_mux(qspi_pin_mux);
+#endif
} else if (board_is_eposevm()) {
configure_module_pin_mux(rmii1_pin_mux);
+#if defined(CONFIG_NAND)
+ configure_module_pin_mux(nand_pin_mux);
+#else
configure_module_pin_mux(qspi_pin_mux);
+#endif
}
}
diff --git a/boards.cfg b/boards.cfg
index 8e2db82..52aeb7f 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -274,7 +274,7 @@ Active arm armv7 am33xx ti am335x
Active arm armv7 am33xx ti am335x am335x_evm_uart4 am335x_evm:SERIAL5,CONS_INDEX=5,NAND Tom Rini <trini at ti.com>
Active arm armv7 am33xx ti am335x am335x_evm_uart5 am335x_evm:SERIAL6,CONS_INDEX=6,NAND Tom Rini <trini at ti.com>
Active arm armv7 am33xx ti am335x am335x_evm_usbspl am335x_evm:SERIAL1,CONS_INDEX=1,NAND,SPL_USBETH_SUPPORT Tom Rini <trini at ti.com>
-Active arm armv7 am33xx ti am43xx am43xx_evm am43xx_evm:SERIAL1,CONS_INDEX=1 Lokesh Vutla <lokeshvutla at ti.com>
+Active arm armv7 am33xx ti am43xx am43xx_evm am43xx_evm:SERIAL1,CONS_INDEX=1,NAND Lokesh Vutla <lokeshvutla at ti.com>
Active arm armv7 am33xx ti am43xx am43xx_evm_qspiboot am43xx_evm:SERIAL1,CONS_INDEX=1,QSPI,QSPI_BOOT Lokesh Vutla <lokeshvutla at ti.com>
Active arm armv7 am33xx ti ti814x ti814x_evm - Matt Porter <matt.porter at linaro.org>
Active arm armv7 am33xx ti ti816x ti816x_evm - -
diff --git a/include/configs/am43xx_evm.h b/include/configs/am43xx_evm.h
index 974ce98..22c9019 100644
--- a/include/configs/am43xx_evm.h
+++ b/include/configs/am43xx_evm.h
@@ -263,4 +263,74 @@
#define CONFIG_SPL_NET_SUPPORT
#define CONFIG_SYS_RX_ETH_BUFFER 64
+/* NAND support */
+#ifdef CONFIG_NAND
+/* NAND: device related configs */
+#define CONFIG_SYS_NAND_PAGE_SIZE 4096
+#define CONFIG_SYS_NAND_OOBSIZE 224
+#define CONFIG_SYS_NAND_BLOCK_SIZE (256*1024)
+#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
+ CONFIG_SYS_NAND_PAGE_SIZE)
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+/* NAND: driver related configs */
+#define CONFIG_SPL_NAND_AM33XX_BCH
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_NAND_OMAP_ELM
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH16_CODE_HW
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
+ 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, \
+ 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, \
+ 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, \
+ 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, \
+ 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, \
+ 60, 61, 62, 63, 64, 65, 66, 67, 68, 69, \
+ 70, 71, 72, 73, 74, 75, 76, 77, 78, 79, \
+ 80, 81, 82, 83, 84, 85, 86, 87, 88, 89, \
+ 90, 91, 92, 93, 94, 95, 96, 97, 98, 99, \
+ 100, 101, 102, 103, 104, 105, 106, 107, 108, 109, \
+ 110, 111, 112, 113, 114, 115, 116, 117, 118, 119, \
+ 120, 121, 122, 123, 124, 125, 126, 127, 128, 129, \
+ 130, 131, 132, 133, 134, 135, 136, 137, 138, 139, \
+ 140, 141, 142, 143, 144, 145, 146, 147, 148, 149, \
+ 150, 151, 152, 153, 154, 155, 156, 157, 158, 159, \
+ 160, 161, 162, 163, 164, 165, 166, 167, 168, 169, \
+ 170, 171, 172, 173, 174, 175, 176, 177, 178, 179, \
+ 180, 181, 182, 183, 184, 185, 186, 187, 188, 189, \
+ 190, 191, 192, 193, 194, 195, 196, 197, 198, 199, \
+ 200, 201, 202, 203, 204, 205, 206, 207, 208, 209, \
+ }
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 26
+#define MTDIDS_DEFAULT "nand0=nand.0"
+#define MTDPARTS_DEFAULT "mtdparts=nand.0:" \
+ "256k(NAND.SPL)," \
+ "256k(NAND.SPL.backup1)," \
+ "256k(NAND.SPL.backup2)," \
+ "256k(NAND.SPL.backup3)," \
+ "512k(NAND.u-boot-spl-os)," \
+ "1m(NAND.u-boot)," \
+ "256k(NAND.u-boot-env)," \
+ "256k(NAND.u-boot-env.backup1)," \
+ "7m(NAND.kernel)," \
+ "-(NAND.rootfs)"
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x00180000
+#define CONFIG_ENV_OFFSET 0x00280000
+#define CONFIG_ENV_OFFSET_REDUND 0x002c0000
+#define CONFIG_SYS_ENV_SECT_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#undef CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_IS_IN_NAND
+/* NAND: SPL related configs */
+#if defined(CONFIG_SPL_NAND_SUPPORT)
+ /* NAND: SPL falcon mode configs */
+ #ifdef CONFIG_SPL_OS_BOOT
+ #undef CONFIG_SPL_OS_BOOT
+ #define CONFIG_CMD_SPL_NAND_OFS 0x00100000 /* os parameters */
+ #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x00300000 /* kernel offset */
+ #define CONFIG_CMD_SPL_WRITE_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+ #endif
+#endif
+#endif /* !CONFIG_NAND */
+
#endif /* __CONFIG_AM43XX_EVM_H */
--
1.8.5.1.163.gd7aced9
More information about the U-Boot
mailing list