[U-Boot] [PATCH v1 3/3] ARM: omap: move board specific NAND configs out from ti_armv7_common.h
Pekon Gupta
pekon at ti.com
Fri Jul 18 14:29:42 CEST 2014
This patch moves some board specific NAND configs:
- FROM: generic config file 'ti_armv7_common.h'
- TO: individual board config files using these configs.
So that each board can independently set the value as per its design.
Following configs are affected in this patch:
CONFIG_SYS_NAND_U_BOOT_OFFS: <refer doc/README.nand>
CONFIG_CMD_SPL_NAND_OFS: <refer doc/README.falcon>
CONFIG_SYS_NAND_SPL_KERNEL_OFFS: <refer doc/README.falcon>
CONFIG_CMD_SPL_WRITE_SIZE: <refer doc/README.falcon>
This patch also updates documentation for few of above NAND configs.
Signed-off-by: Pekon Gupta <pekon at ti.com>
---
doc/README.nand | 12 ++++++++++++
include/configs/am335x_evm.h | 5 +++++
include/configs/cm_t335.h | 5 +++++
include/configs/omap3_beagle.h | 6 ++++++
include/configs/omap3_igep00x0.h | 7 +++++++
include/configs/omap3_overo.h | 6 ++++++
include/configs/omap3_zoom1.h | 6 ++++++
include/configs/pengwyn.h | 6 ++++++
include/configs/ti_armv7_common.h | 8 --------
9 files changed, 53 insertions(+), 8 deletions(-)
diff --git a/doc/README.nand b/doc/README.nand
index 70cf768..e29188f 100644
--- a/doc/README.nand
+++ b/doc/README.nand
@@ -89,6 +89,10 @@ Commands:
Configuration Options:
+ CONFIG_SYS_NAND_U_BOOT_OFFS
+ NAND Offset from where SPL will read u-boot image. This is the starting
+ address of u-boot MTD partition in NAND.
+
CONFIG_CMD_NAND
Enables NAND support and commmands.
@@ -226,6 +230,14 @@ Platform specific options
detection. However ECC calculation on such plaforms would still be
done by GPMC controller.
+ CONFIG_SPL_NAND_AM33XX_BCH
+ Enables SPL-NAND driver (am335x_spl_bch.c) which supports ELM based
+ hardware ECC correction. This is useful for platforms which have ELM
+ hardware engine and use NAND boot mode.
+ Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine,
+ so those platforms should use CONFIG_SPL_NAND_SIMPLE for enabling
+ SPL-NAND driver with software ECC correction support.
+
CONFIG_NAND_OMAP_ECCSCHEME
On OMAP platforms, this CONFIG specifies NAND ECC scheme.
It can take following values:
diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h
index c1a6ada..f5bfd5d 100644
--- a/include/configs/am335x_evm.h
+++ b/include/configs/am335x_evm.h
@@ -254,6 +254,11 @@
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_CMD_SPL_NAND_OFS 0x00080000 /* os parameters */
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x00200000 /* kernel offset */
+#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
+#endif
#endif
#endif
diff --git a/include/configs/cm_t335.h b/include/configs/cm_t335.h
index 4d1dd28..a3e6452 100644
--- a/include/configs/cm_t335.h
+++ b/include/configs/cm_t335.h
@@ -150,6 +150,11 @@
#define CONFIG_ENV_OFFSET 0x300000 /* environment starts here */
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
#define CONFIG_SYS_NAND_ONFI_DETECTION
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_CMD_SPL_NAND_OFS 0x400000 /* un-assigned: (using dtb) */
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x500000
+#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
+#endif
/* GPIO pin + bank to pin ID mapping */
#define GPIO_PIN(_bank, _pin) ((_bank << 5) + _pin)
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index 74a3d1a..b665979 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -304,5 +304,11 @@
#define CONFIG_SYS_NAND_ECCBYTES 3
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+/* NAND: SPL falcon mode configs */
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_CMD_SPL_NAND_OFS 0x240000
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
+#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
+#endif
#endif /* __CONFIG_H */
diff --git a/include/configs/omap3_igep00x0.h b/include/configs/omap3_igep00x0.h
index 0bb79ab..006c9a9 100644
--- a/include/configs/omap3_igep00x0.h
+++ b/include/configs/omap3_igep00x0.h
@@ -196,6 +196,13 @@
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 3
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+/* NAND: SPL falcon mode configs */
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_CMD_SPL_NAND_OFS 0x240000
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
+#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
+#endif
#endif
#endif /* __IGEP00X0_H */
diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h
index 38f8dab..e66f306 100644
--- a/include/configs/omap3_overo.h
+++ b/include/configs/omap3_overo.h
@@ -216,5 +216,11 @@
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+/* NAND: SPL falcon mode configs */
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_CMD_SPL_NAND_OFS 0x240000
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
+#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
+#endif
#endif /* __CONFIG_H */
diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h
index 236281a..93f4d62 100644
--- a/include/configs/omap3_zoom1.h
+++ b/include/configs/omap3_zoom1.h
@@ -70,6 +70,12 @@
"4m(kernel),-(fs)"
#if defined(CONFIG_CMD_NAND)
+/* NAND: SPL falcon mode configs */
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_CMD_SPL_NAND_OFS 0x240000
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
+#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
+#endif
#define CONFIG_CMD_NAND_LOCK_UNLOCK /* Enable lock/unlock support */
#endif
diff --git a/include/configs/pengwyn.h b/include/configs/pengwyn.h
index 8510405..4684ad6 100644
--- a/include/configs/pengwyn.h
+++ b/include/configs/pengwyn.h
@@ -159,6 +159,12 @@
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET 0x260000 /* environment starts here */
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
+/* NAND: SPL falcon mode configs */
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_CMD_SPL_NAND_OFS 0x240000 /* un-assigned */
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
+#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
+#endif
/*
* USB configuration. We enable MUSB support, both for host and for
diff --git a/include/configs/ti_armv7_common.h b/include/configs/ti_armv7_common.h
index 6e0bf09..85c027c 100644
--- a/include/configs/ti_armv7_common.h
+++ b/include/configs/ti_armv7_common.h
@@ -243,13 +243,6 @@
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */
-/* NAND */
-#ifdef CONFIG_NAND
-#define CONFIG_CMD_SPL_NAND_OFS 0x240000 /* end of u-boot */
-#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
-#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
-#endif
-
/* spl export command */
#define CONFIG_CMD_SPL
#endif
@@ -275,7 +268,6 @@
#define CONFIG_SPL_NAND_ECC
#define CONFIG_SPL_MTD_SUPPORT
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
#endif
#endif /* !CONFIG_NOR_BOOT */
--
1.8.5.1.163.gd7aced9
More information about the U-Boot
mailing list