[U-Boot] [PATCH] arm: bcm281xx: Add Ethernet Clock support
Steve Rae
srae at broadcom.com
Sat Jul 26 01:44:45 CEST 2014
From: Jiandong Zheng <jdzheng at broadcom.com>
Enable Ethernet clock when Broadcom StarFighter2 Ethernet block
(CONFIG_BCM_SF2_ETH) is enabled.
Signed-off-by: Jiandong Zheng <jdzheng at broadcom.com>
Signed-off-by: Steve Rae <srae at broadcom.com>
---
- added board with this feature enabled
arch/arm/cpu/armv7/bcm281xx/Makefile | 1 +
arch/arm/cpu/armv7/bcm281xx/clk-bcm281xx.c | 34 +++++++
arch/arm/cpu/armv7/bcm281xx/clk-eth.c | 143 ++++++++++++++++++++++++++++
arch/arm/include/asm/arch-bcm281xx/sysmap.h | 3 +
boards.cfg | 1 +
5 files changed, 182 insertions(+)
create mode 100644 arch/arm/cpu/armv7/bcm281xx/clk-eth.c
diff --git a/arch/arm/cpu/armv7/bcm281xx/Makefile b/arch/arm/cpu/armv7/bcm281xx/Makefile
index 98f5aa5..bd867a2 100644
--- a/arch/arm/cpu/armv7/bcm281xx/Makefile
+++ b/arch/arm/cpu/armv7/bcm281xx/Makefile
@@ -9,3 +9,4 @@ obj-y += clk-core.o
obj-y += clk-bcm281xx.o
obj-y += clk-sdio.o
obj-y += clk-bsc.o
+obj-$(CONFIG_BCM_SF2_ETH) += clk-eth.o
diff --git a/arch/arm/cpu/armv7/bcm281xx/clk-bcm281xx.c b/arch/arm/cpu/armv7/bcm281xx/clk-bcm281xx.c
index bc8a170..d16b99f 100644
--- a/arch/arm/cpu/armv7/bcm281xx/clk-bcm281xx.c
+++ b/arch/arm/cpu/armv7/bcm281xx/clk-bcm281xx.c
@@ -118,6 +118,16 @@ unsigned long slave_apb_freq_tbl[8] = {
78 * CLOCK_1M
};
+unsigned long esub_freq_tbl[8] = {
+ 78 * CLOCK_1M,
+ 156 * CLOCK_1M,
+ 156 * CLOCK_1M,
+ 156 * CLOCK_1M,
+ 208 * CLOCK_1M,
+ 208 * CLOCK_1M,
+ 208 * CLOCK_1M
+};
+
static struct bus_clk_data bsc1_apb_data = {
.gate = HW_SW_GATE_AUTO(0x0458, 16, 0, 1),
};
@@ -295,6 +305,27 @@ static struct ccu_clock kps_ccu_clk = {
.freq_tbl = slave_axi_freq_tbl,
};
+#ifdef CONFIG_BCM_SF2_ETH
+static struct ccu_clock esub_ccu_clk = {
+ .clk = {
+ .name = "esub_ccu_clk",
+ .ops = &ccu_clk_ops,
+ .ccu_clk_mgr_base = ESUB_CLK_BASE_ADDR,
+ },
+ .num_policy_masks = 1,
+ .policy_freq_offset = 0x00000008,
+ .freq_bit_shift = 8,
+ .policy_ctl_offset = 0x0000000c,
+ .policy0_mask_offset = 0x00000010,
+ .policy1_mask_offset = 0x00000014,
+ .policy2_mask_offset = 0x00000018,
+ .policy3_mask_offset = 0x0000001c,
+ .lvm_en_offset = 0x00000034,
+ .freq_id = 2,
+ .freq_tbl = esub_freq_tbl,
+};
+#endif
+
/*
* Bus clocks
*/
@@ -517,6 +548,9 @@ struct clk_lookup arch_clk_tbl[] = {
CLK_LK(bsc1_apb),
CLK_LK(bsc2_apb),
CLK_LK(bsc3_apb),
+#ifdef CONFIG_BCM_SF2_ETH
+ CLK_LK(esub_ccu),
+#endif
};
/* public array size */
diff --git a/arch/arm/cpu/armv7/bcm281xx/clk-eth.c b/arch/arm/cpu/armv7/bcm281xx/clk-eth.c
new file mode 100644
index 0000000..b0b92b9
--- /dev/null
+++ b/arch/arm/cpu/armv7/bcm281xx/clk-eth.c
@@ -0,0 +1,143 @@
+/*
+ * Copyright 2014 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/arch/sysmap.h>
+#include <asm/kona-common/clk.h>
+#include "clk-core.h"
+
+#define WR_ACCESS_ADDR ESUB_CLK_BASE_ADDR
+#define WR_ACCESS_PASSWORD 0xA5A500
+
+#define PLLE_POST_RESETB_ADDR (ESUB_CLK_BASE_ADDR + 0x00000C00)
+
+#define PLLE_RESETB_ADDR (ESUB_CLK_BASE_ADDR + 0x00000C58)
+#define PLLE_RESETB_I_PLL_RESETB_PLLE_MASK 0x00010000
+#define PLLE_POST_RESETB_I_POST_RESETB_PLLE_MASK 0x00000001
+
+#define PLL_LOCK_ADDR (ESUB_CLK_BASE_ADDR + 0x00000C38)
+#define PLL_LOCK_PLL_LOCK_PLLE_MASK 0x00000001
+
+#define ESW_SYS_DIV_ADDR (ESUB_CLK_BASE_ADDR + 0x00000A04)
+#define ESW_SYS_DIV_PLL_SELECT_MASK 0x00000300
+#define ESW_SYS_DIV_DIV_MASK 0x0000001C
+#define ESW_SYS_DIV_PLL_VAR_208M_CLK_SELECT 0x00000100
+#define ESW_SYS_DIV_DIV_SELECT 0x4
+#define ESW_SYS_DIV_TRIGGER_MASK 0x00000001
+
+#define ESUB_AXI_DIV_DEBUG_ADDR (ESUB_CLK_BASE_ADDR + 0x00000E04)
+#define ESUB_AXI_DIV_DEBUG_PLL_SELECT_MASK 0x0000001C
+#define ESUB_AXI_DIV_DEBUG_PLL_SELECT_OVERRIDE_MASK 0x00000040
+#define ESUB_AXI_DIV_DEBUG_PLL_VAR_208M_CLK_SELECT 0x0
+#define ESUB_AXI_DIV_DEBUG_TRIGGER_MASK 0x00000001
+
+#define PLL_MAX_RETRY 100
+
+/* Enable appropriate clocks for Ethernet */
+int clk_eth_enable(void)
+{
+ int rc = -1;
+ int retry_count = 0;
+ rc = clk_get_and_enable("esub_ccu_clk");
+
+ /* Enable Access to CCU registers */
+ writel((1 | WR_ACCESS_PASSWORD), WR_ACCESS_ADDR);
+
+ writel(readl(PLLE_POST_RESETB_ADDR) &
+ ~PLLE_POST_RESETB_I_POST_RESETB_PLLE_MASK,
+ PLLE_POST_RESETB_ADDR);
+
+ /* Take PLL out of reset and put into normal mode */
+ writel(readl(PLLE_RESETB_ADDR) | PLLE_RESETB_I_PLL_RESETB_PLLE_MASK,
+ PLLE_RESETB_ADDR);
+
+ /* Wait for PLL lock */
+ rc = -1;
+ while (retry_count < PLL_MAX_RETRY) {
+ udelay(100);
+ if (readl(PLL_LOCK_ADDR) & PLL_LOCK_PLL_LOCK_PLLE_MASK) {
+ rc = 0;
+ break;
+ }
+ retry_count++;
+ }
+
+ if (rc == -1) {
+ printf("%s: ETH-PLL lock timeout, Ethernet is not enabled!\n",
+ __func__);
+ return -1;
+ }
+
+ writel(readl(PLLE_POST_RESETB_ADDR) |
+ PLLE_POST_RESETB_I_POST_RESETB_PLLE_MASK,
+ PLLE_POST_RESETB_ADDR);
+
+ /* Switch esw_sys_clk to use 104MHz(208MHz/2) clock */
+ writel((readl(ESW_SYS_DIV_ADDR) &
+ ~(ESW_SYS_DIV_PLL_SELECT_MASK | ESW_SYS_DIV_DIV_MASK)) |
+ ESW_SYS_DIV_PLL_VAR_208M_CLK_SELECT | ESW_SYS_DIV_DIV_SELECT,
+ ESW_SYS_DIV_ADDR);
+
+ writel(readl(ESW_SYS_DIV_ADDR) | ESW_SYS_DIV_TRIGGER_MASK,
+ ESW_SYS_DIV_ADDR);
+
+ /* Wait for trigger complete */
+ rc = -1;
+ retry_count = 0;
+ while (retry_count < PLL_MAX_RETRY) {
+ udelay(100);
+ if (!(readl(ESW_SYS_DIV_ADDR) & ESW_SYS_DIV_TRIGGER_MASK)) {
+ rc = 0;
+ break;
+ }
+ retry_count++;
+ }
+
+ if (rc == -1) {
+ printf("%s: SYS CLK Trigger timeout, Ethernet is not enabled!\n",
+ __func__);
+ return -1;
+ }
+
+ /* switch Esub AXI clock to 208MHz */
+ writel((readl(ESUB_AXI_DIV_DEBUG_ADDR) &
+ ~(ESUB_AXI_DIV_DEBUG_PLL_SELECT_MASK |
+ ESUB_AXI_DIV_DEBUG_PLL_SELECT_OVERRIDE_MASK |
+ ESUB_AXI_DIV_DEBUG_TRIGGER_MASK)) |
+ ESUB_AXI_DIV_DEBUG_PLL_VAR_208M_CLK_SELECT |
+ ESUB_AXI_DIV_DEBUG_PLL_SELECT_OVERRIDE_MASK,
+ ESUB_AXI_DIV_DEBUG_ADDR);
+
+ writel(readl(ESUB_AXI_DIV_DEBUG_ADDR) |
+ ESUB_AXI_DIV_DEBUG_TRIGGER_MASK,
+ ESUB_AXI_DIV_DEBUG_ADDR);
+
+ /* Wait for trigger complete */
+ rc = -1;
+ retry_count = 0;
+ while (retry_count < PLL_MAX_RETRY) {
+ udelay(100);
+ if (!(readl(ESUB_AXI_DIV_DEBUG_ADDR) &
+ ESUB_AXI_DIV_DEBUG_TRIGGER_MASK)) {
+ rc = 0;
+ break;
+ }
+ retry_count++;
+ }
+
+ if (rc == -1) {
+ printf("%s: AXI CLK Trigger timeout, Ethernet is not enabled!\n",
+ __func__);
+ return -1;
+ }
+
+ /* Disable Access to CCU registers */
+ writel(WR_ACCESS_PASSWORD, WR_ACCESS_ADDR);
+
+ return rc;
+}
diff --git a/arch/arm/include/asm/arch-bcm281xx/sysmap.h b/arch/arm/include/asm/arch-bcm281xx/sysmap.h
index 880b4e0..350e7f6 100644
--- a/arch/arm/include/asm/arch-bcm281xx/sysmap.h
+++ b/arch/arm/include/asm/arch-bcm281xx/sysmap.h
@@ -9,6 +9,9 @@
#define BSC1_BASE_ADDR 0x3e016000
#define BSC2_BASE_ADDR 0x3e017000
#define BSC3_BASE_ADDR 0x3e018000
+#define DWDMA_AHB_BASE_ADDR 0x38100000
+#define ESUB_CLK_BASE_ADDR 0x38000000
+#define ESW_CONTRL_BASE_ADDR 0x38200000
#define GPIO2_BASE_ADDR 0x35003000
#define KONA_MST_CLK_BASE_ADDR 0x3f001000
#define KONA_SLV_CLK_BASE_ADDR 0x3e011000
diff --git a/boards.cfg b/boards.cfg
index 4b2bc19..d5427df 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -289,6 +289,7 @@ Active arm armv7 at91 atmel sama5d3xek
Active arm armv7 at91 atmel sama5d3xek sama5d3xek_nandflash sama5d3xek:SAMA5D3,SYS_USE_NANDFLASH Bo Shen <voice.shen at atmel.com>
Active arm armv7 at91 atmel sama5d3xek sama5d3xek_spiflash sama5d3xek:SAMA5D3,SYS_USE_SERIALFLASH Bo Shen <voice.shen at atmel.com>
Active arm armv7 bcm281xx broadcom bcm28155_ap bcm28155_ap bcm28155_ap Tim Kryger <tim.kryger at linaro.org>
+Active arm armv7 bcm281xx broadcom bcm28155_ap bcm28155_w1d bcm28155_ap:BCM_SF2_ETH Steve Rae <srae at broadcom.com>
Active arm armv7 exynos samsung arndale arndale - Inderpal Singh <inderpal.singh at linaro.org>
Active arm armv7 exynos samsung origen origen - Chander Kashyap <k.chander at samsung.com>
Active arm armv7 exynos samsung smdk5250 smdk5250 - Chander Kashyap <k.chander at samsung.com>
--
1.8.5
More information about the U-Boot
mailing list