[U-Boot] [PATCH 12/12] imx: ventana: switch to SPL

[Stefano Babic]

Hi Tim,

On 06/05/2014 20:18, Tim Harvey wrote:
> 
> Stefano / York,
> 
> While preparing for a v3 patch series of my IMX6 SPL bootloader, I
> find that commit dec1861be90c948ea9fb771927d3d26a994d2e20 [1] breaks
> the above code because gd is now needed within setup_i2c.
> 
> I've always been a bit fuzzy on the order of the above calls so I dug
> through the code and I think I understand things better. Please
> correct any wrong assumptions I'm making below:
>  - assignment to gd should 'always' be first (before anything needs
> it, so why not do it first)
>  - arch_cpu_init() should go next as this sets up very low level
> CPU/SoC resources (in this case AIPS config and watchdog disable)
>  - board_early_init_f() should be next as that sets up any board-specific iomux
>  - any additional iomux necessary for SPL should go next (I take care
> of i2c iomux and setup here)
>  - timer_init() next as you need a timer for UART and mxc i2c (for
> delays and busy checks)
>  - preloader_console_init() next as we are now able to send something
> over the UART (this gives me early debug for sdram config now too!)
>  - sdram setup goes next
>  - after sdram is setup, the bss can be cleared
>  - board_init_r - pass over to generic SPL code which will load/call
> an image based on boot device

I think your analyses is correct.

> 
> So, if the above is correct, I should rework the above function as follows:
> 
> void board_init_f(ulong dummy)
> {
>         struct ventana_board_info ventana_info;
>         int board_model;
> 
>         /* Set global data pointer. */
>         gd = &gdata;
> 
>         /* setup AIPS and disable watchdog */
>         arch_cpu_init();
> 
>         /* iomux and setup of i2c */
>         board_early_init_f();
>         i2c_setup_iomux();
> 
>         /* setup GP timer */
>         timer_init();
> 
>         /* UART clocks enabled and gd valid - init serial console */
>         preloader_console_init();
> 
>         /* read/validate EEPROM info to determine board model and SDRAM cfg */
>         board_model = read_eeprom(I2C_GSC, &ventana_info);
> 
>         /* provide some some default: 32bit 128MB */
>         if (GW_UNKNOWN == board_model) {
>                 ventana_info.sdram_width = 2;
>                 ventana_info.sdram_size = 3;
>         }
> 
>         /* configure MMDC for SDRAM width/size and per-model calibration */
>         spl_dram_init(8 << ventana_info.sdram_width,
>                       16 << ventana_info.sdram_size,
>                       board_model);
> 
>         /* Clear the BSS. */
>         memset(__bss_start, 0, __bss_end - __bss_start);
> 
>         /* load/boot image from boot device */
>         board_init_r(NULL, 0);
> }

It seems reasonable, go on this way.

Regards,
Stefano



-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================