[U-Boot] [PATCH v3] arm: Add support for semihosting for armv8 fastmodel targets.
bhupesh.sharma at freescale.com
bhupesh.sharma at freescale.com
Fri May 23 14:05:50 CEST 2014
Hi Darwin,
> -----Original Message-----
> From: Darwin Rambo [mailto:drambo at broadcom.com]
> Sent: Tuesday, March 25, 2014 12:46 AM
> To: u-boot at lists.denx.de
> Cc: Darwin Rambo; Albert Aribaud; Tom Rini; fenghua at phytium.com.cn;
> Sharma Bhupesh-B45370
> Subject: [PATCH v3] arm: Add support for semihosting for armv8 fastmodel
> targets.
>
> The reason for this change is to be able to use the ARM Trusted Firmware
> (ATF) to load the various ATF images, plus u-boot, which can then load
> the kernel/ramdisk/dtb with calls to an external host from a standard
> fastmodel armv8 board file using semihosting, and then launch the kernel
> without a bootwrapper. This gives us a more realistic boot sequence.
>
> There are two main ARM virtual Fixed Virtual Platform (FVP) models,
> Versatile Express (VE) FVP and BASE FVP (See
> http://www.arm.com/products/tools/models/fast-models/foundation-
> model.php)
> The initial vexpress64 u-boot board created here runs on the VE virtual
> platform using the license-free Foundation_v8 simulator. Fortunately, the
> Foundation_v8 simulator also supports the BASE_FVP model which companies
> can purchase licenses for and contain much more functionality.
> So we can, in u-boot, run either model by either using the VE FVP
> (default), or turning on CONFIG_BASE_FVP for the more full featured
> model.
>
> Rather than create a new armv8 board similar to armltd/vexpress64, add
> semihosting calls to the existing one, enabled with CONFIG_SEMIHOSTING
> and CONFIG_BASE_FVP both set. Also reuse the existing board config file
> vexpress_aemv8a.h but differentiate the two models by the presence or
> absence of CONFIG_BASE_FVP. This change is tested and works on both the
> Foundation and Base fastmodel simulators.
>
> Support for armv7 in fastmodel is less useful due to the wide range of
> available silicon and the lack of a free armv7 fastmodel, so this change
> contains an untested armv7 placeholder for the service trap opcode.
>
> The level of semihosting support is minimal, restricted to just what it
> takes to load images to memory. If more semihosting functionality is
> required, such as file seek, outputting strings, reading characters, etc,
> then it can be easily added later.
Sorry for the late reply. We are using ARMv8 foundation model (the free version)
to launch u-boot via the ARM Trusted Firmware (ATF). We are using a older
u-boot version and cannot see the ATF launching the u-boot.bin.
Please find the details of the ARMv8 foundation model command line and ATF, u-boot commit
logs below (Host machine is a ubuntu-64 bit).
ARMv8 foundation model Command Line used
-----------------------------------------
$ ./Foundation_v8 --cores=1 --no-secure-memory --visualization --gicv3 --data="bl1.bin"@0x00000000 --data="fip.bin"@0x80000000
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.
Booting trusted firmware boot loader stage 1
Built : 12:58:21, May 22 2014
ERROR: Firmware Image Package header check failed.
Booting trusted firmware boot loader stage 2
BL2 Built : 12:58:22, May 22 2014
ERROR: Firmware Image Package header check failed.
ERROR: Firmware Image Package header check failed.
Booting trusted firmware boot loader stage 3
BL31 Built : 12:58:23, May 22 2014
ATF latest commit
-----------------
commit ca823d2c881d9d8c7db364de7e362d2e75ad55df
Author: Achin Gupta <achin.gupta at arm.com>
Date: Sun Feb 2 13:04:00 2014 +0000
Increase coherent stack sizes
This patch increases coherent stack size for both debug and release
builds in order to accommodate stack-heavy printf() and extended EL3
functionality
Change-Id: I30ef30530a01517a97e63d703873374828c09f20
u-boot commit
-------------
commit 22a240c32c1340183fce12867ae5f8736b92a638
Author: Alexey Brodkin <Alexey.Brodkin at synopsys.com>
Date: Fri Dec 13 10:35:11 2013 +0400
serial/serial_arc - add driver for ARC UART
Driver for non-standard on-chip UART, instantiated in the ARC (Synopsys)
FPGA Boards such as ARCAngel4/ML50x
Signed-off-by: Alexey Brodkin <abrodkin at synopsys.com
Regards,
Bhupesh
> Signed-off-by: Darwin Rambo <drambo at broadcom.com>
> ---
>
> Changes in v3:
> - minor format fixup in board file
>
> Changes in v2:
> - use kernel_addr_r, fdt_addr_r, initrd_addr_r convention.
> - Use env variables for kernel/fdt/initrd file names.
> - Add CONFIG_BASE_FVP to differentiate VE and BASE FVP models.
> - CONFIG_SEMIHOSTING only refers to bringing in semihosting code now.
> - Remove unnecessary CONFIG_SYS_BAUDRATE_TABLE,
> CONFIG_SYS_PROMPT_HUSH_PS2
> - Remove vexpress_aemv8a_semi.h and replace with CONFIG_BASE_FVP
> - Update boards.cfg with option SEMIHOSTING and BASE_FVP
> - Add doc/README.semihosting
>
> Changes in v1:
> - Initial code
> - Remove empty timer_init() function.
>
> arch/arm/include/asm/semihosting.h | 21 +++
> arch/arm/lib/Makefile | 1 +
> arch/arm/lib/semihosting.c | 235
> ++++++++++++++++++++++++++++++++++
> board/armltd/vexpress64/vexpress64.c | 101 ++++++++++++++-
> boards.cfg | 1 +
> doc/README.semihosting | 35 +++++
> include/configs/vexpress_aemv8a.h | 59 ++++++++-
> 7 files changed, 441 insertions(+), 12 deletions(-) create mode 100644
> arch/arm/include/asm/semihosting.h
> create mode 100644 arch/arm/lib/semihosting.c create mode 100644
> doc/README.semihosting
>
> diff --git a/arch/arm/include/asm/semihosting.h
> b/arch/arm/include/asm/semihosting.h
> new file mode 100644
> index 0000000..74111dc
> --- /dev/null
> +++ b/arch/arm/include/asm/semihosting.h
> @@ -0,0 +1,21 @@
> +/*
> + * Copyright 2014 Broadcom Corporation
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __SEMIHOSTING_H__
> +#define __SEMIHOSTING_H__
> +
> +/*
> + * ARM semihosting functions for loading images to memory. See the
> +source
> + * code for more information.
> + */
> +int smh_load(const char *fname, void *memp, int avail, int verbose);
> +int smh_read(int fd, void *memp, int len); int smh_open(const char
> +*fname, char *modestr); int smh_close(int fd); int smh_len_fd(int fd);
> +int smh_len(const char *fname);
> +
> +#endif /* __SEMIHOSTING_H__ */
> diff --git a/arch/arm/lib/Makefile b/arch/arm/lib/Makefile index
> 9fc81cd..0ba929d 100644
> --- a/arch/arm/lib/Makefile
> +++ b/arch/arm/lib/Makefile
> @@ -32,6 +32,7 @@ obj-$(CONFIG_USE_ARCH_MEMCPY) += memcpy.o else
> obj-$(CONFIG_SPL_FRAMEWORK) += spl.o
> endif
> +obj-$(CONFIG_SEMIHOSTING) += semihosting.o
>
> obj-y += sections.o
> ifdef CONFIG_ARM64
> diff --git a/arch/arm/lib/semihosting.c b/arch/arm/lib/semihosting.c new
> file mode 100644 index 0000000..d603789
> --- /dev/null
> +++ b/arch/arm/lib/semihosting.c
> @@ -0,0 +1,235 @@
> +/*
> + * Copyright 2014 Broadcom Corporation
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +/*
> + * Minimal semihosting implementation for reading files into memory. If
> +more
> + * features like writing files or console output are required they can
> +be
> + * added later. This code has been tested on arm64/aarch64 fastmodel
> only.
> + * An untested placeholder exists for armv7 architectures, but since
> +they
> + * are commonly available in silicon now, fastmodel usage makes less
> +sense
> + * for them.
> + */
> +#include <common.h>
> +#include <asm/semihosting.h>
> +
> +#define SYSOPEN 0x01
> +#define SYSCLOSE 0x02
> +#define SYSREAD 0x06
> +#define SYSFLEN 0x0C
> +
> +#define MODE_READ 0x0
> +#define MODE_READBIN 0x1
> +
> +/*
> + * Call the handler
> + */
> +static int smh_trap(unsigned int sysnum, void *addr) {
> + register int result asm("r0");
> +#if defined(CONFIG_ARM64)
> + asm volatile ("hlt #0xf000" : "=r" (result) : "0"(sysnum),
> "r"(addr));
> +#else
> + /* Note - untested placeholder */
> + asm volatile ("svc #0x123456" : "=r" (result) : "0"(sysnum),
> +"r"(addr)); #endif
> + return result;
> +}
> +
> +/*
> + * Open, load a file into memory, and close it. Check that the
> +available space
> + * is sufficient to store the entire file. Return the bytes actually
> +read from
> + * the file as seen by the read function. The verbose flag enables some
> +extra
> + * printing of successful read status.
> + */
> +int smh_load(const char *fname, void *memp, int avail, int verbose) {
> + int ret, fd, len;
> +
> + ret = -1;
> +
> + debug("%s: fname \'%s\', avail %u, memp %p\n", __func__, fname,
> + avail, memp);
> +
> + /* Open the file */
> + fd = smh_open(fname, "rb");
> + if (fd == -1)
> + return ret;
> +
> + /* Get the file length */
> + ret = smh_len_fd(fd);
> + if (ret == -1) {
> + smh_close(fd);
> + return ret;
> + }
> +
> + /* Check that the file will fit in the supplied buffer */
> + if (ret > avail) {
> + printf("%s: ERROR ret %d, avail %u\n", __func__, ret,
> + avail);
> + smh_close(fd);
> + return ret;
> + }
> +
> + len = ret;
> +
> + /* Read the file into the buffer */
> + ret = smh_read(fd, memp, len);
> + if (ret == 0) {
> + /* Print successful load information if requested */
> + if (verbose) {
> + printf("\n%s\n", fname);
> + printf(" 0x%8p dest\n", memp);
> + printf(" 0x%08x size\n", len);
> + printf(" 0x%08x avail\n", avail);
> + }
> + }
> +
> + /* Close the file */
> + smh_close(fd);
> +
> + return ret;
> +}
> +
> +/*
> + * Read 'len' bytes of file into 'memp'. Returns 0 on success, else
> +failure */ int smh_read(int fd, void *memp, int len) {
> + int ret;
> + struct smh_read_s {
> + int fd;
> + void *memp;
> + int len;
> + } read;
> +
> + debug("%s: fd %d, memp %p, len %d\n", __func__, fd, memp, len);
> +
> + read.fd = fd;
> + read.memp = memp;
> + read.len = len;
> +
> + ret = smh_trap(SYSREAD, &read);
> + if (ret == 0) {
> + return 0;
> + } else {
> + /*
> + * The ARM handler allows for returning partial lengths,
> + * but if this ever happens, it is a bug in the fastmodel
> + * implementation. The Linux fastmodel doesn't show this
> + * issue, and any Windows fastmodel bugs need to be fixed.
> + * So rather than create ugly unmaintainable partial read
> + * loops and such, just fail with an error message.
> + */
> + printf("%s: ERROR ret %d, fd %d, len %u memp %p\n",
> + __func__, ret, fd, len, memp);
> + }
> + return ret;
> +}
> +
> +/*
> + * Open a file on the host. Mode is "r" or "rb" currently. Returns a
> +file
> + * descriptor or -1 on error.
> + */
> +int smh_open(const char *fname, char *modestr) {
> + int ret, fd, mode;
> + struct smh_open_s {
> + const char *fname;
> + unsigned int mode;
> + unsigned int len;
> + } open;
> +
> + debug("%s: file \'%s\', mode \'%s\'\n", __func__, fname, modestr);
> +
> + ret = -1;
> +
> + /* Check the file mode */
> + if (!(strcmp(modestr, "r"))) {
> + mode = MODE_READ;
> + } else if (!(strcmp(modestr, "rb"))) {
> + mode = MODE_READBIN;
> + } else {
> + printf("%s: ERROR mode \'%s\' not supported\n", __func__,
> + modestr);
> + return ret;
> + }
> +
> + open.fname = fname;
> + open.len = strlen(fname);
> + open.mode = mode;
> +
> + /* Open the file on the host */
> + fd = smh_trap(SYSOPEN, &open);
> + if (fd == -1)
> + printf("%s: ERROR fd %d for file \'%s\'\n", __func__, fd,
> + fname);
> +
> + return fd;
> +}
> +
> +/*
> + * Close the file using the file descriptor */ int smh_close(int fd) {
> + int ret;
> + long fdlong;
> +
> + debug("%s: fd %d\n", __func__, fd);
> +
> + fdlong = (long)fd;
> + ret = smh_trap(SYSCLOSE, &fdlong);
> + if (ret == -1)
> + printf("%s: ERROR fd %d\n", __func__, fd);
> +
> + return ret;
> +}
> +
> +/*
> + * Get the file length from the file descriptor */ int smh_len_fd(int
> +fd) {
> + int ret;
> + long fdlong;
> +
> + debug("%s: fd %d\n", __func__, fd);
> +
> + fdlong = (long)fd;
> + ret = smh_trap(SYSFLEN, &fdlong);
> + if (ret == -1)
> + printf("%s: ERROR ret %d\n", __func__, ret);
> +
> + return ret;
> +}
> +
> +/*
> + * Get the file length from the filename */ int smh_len(const char
> +*fname) {
> + int ret, fd, len;
> +
> + debug("%s: file \'%s\'\n", __func__, fname);
> +
> + /* Open the file */
> + fd = smh_open(fname, "rb");
> + if (fd == -1)
> + return fd;
> +
> + /* Get the file length */
> + len = smh_len_fd(fd);
> +
> + /* Close the file */
> + ret = smh_close(fd);
> + if (ret == -1)
> + return ret;
> +
> + debug("%s: returning len %d\n", __func__, len);
> +
> + /* Return the file length (or -1 error indication) */
> + return len;
> +}
> diff --git a/board/armltd/vexpress64/vexpress64.c
> b/board/armltd/vexpress64/vexpress64.c
> index 2ec3bc9..5897318 100644
> --- a/board/armltd/vexpress64/vexpress64.c
> +++ b/board/armltd/vexpress64/vexpress64.c
> @@ -11,6 +11,7 @@
> #include <netdev.h>
> #include <asm/io.h>
> #include <linux/compiler.h>
> +#include <asm/semihosting.h>
>
> DECLARE_GLOBAL_DATA_PTR;
>
> @@ -31,11 +32,6 @@ int dram_init(void)
> return 0;
> }
>
> -int timer_init(void)
> -{
> - return 0;
> -}
> -
> /*
> * Board specific reset that is system reset.
> */
> @@ -43,6 +39,101 @@ void reset_cpu(ulong addr) { }
>
> +#ifdef CONFIG_BOARD_LATE_INIT
> +int board_late_init(void)
> +{
> +#ifdef CONFIG_SEMIHOSTING
> + /*
> + * Please refer to doc/README.semihosting for a more complete
> + * description.
> + *
> + * We require that the board include file defines these env
> variables:
> + * - kernel_name
> + * - kernel_addr_r
> + * - initrd_name
> + * - initrd_addr_r
> + * - fdt_name
> + * - fdt_addr_r
> + *
> + * For the "fdt chosen" startup macro, this code will then define:
> + * - initrd_end (based on initrd_addr_r plus actual initrd_size)
> + *
> + * We will then load the kernel, initrd, and fdt into the specified
> + * locations in memory in a similar way that the ATF fastmodel code
> + * uses semihosting calls to load other boot stages and u-boot
> itself.
> + */
> +
> + /* Env variable strings */
> + char *kernel_name = getenv("kernel_name");
> + char *kernel_addr_str = getenv("kernel_addr_r");
> + char *initrd_name = getenv("initrd_name");
> + char *initrd_addr_str = getenv("initrd_addr_r");
> + char *fdt_name = getenv("fdt_name");
> + char *fdt_addr_str = getenv("fdt_addr_r");
> + char initrd_end_str[64];
> +
> + /* Actual addresses converted from env variables */
> + void *kernel_addr_r;
> + void *initrd_addr_r;
> + void *fdt_addr_r;
> +
> + /* Actual initrd base and size */
> + unsigned long initrd_base;
> + unsigned long initrd_size;
> +
> + /* Space available */
> + int avail;
> +
> + /* Make sure the environment variables needed are set */
> + if (!(kernel_addr_str && initrd_addr_str && fdt_addr_str)) {
> + printf("%s: Define {kernel/initrd/fdt}_addr_r\n", __func__);
> + return -1;
> + }
> + if (!(kernel_name && initrd_name && fdt_name)) {
> + printf("%s: Define {kernel/initrd/fdt}_name\n", __func__);
> + return -1;
> + }
> +
> + /* Get exact initrd_size */
> + initrd_size = smh_len(initrd_name);
> + if (initrd_size == -1) {
> + printf("%s: Can't get file size for \'%s\'\n", __func__,
> + initrd_name);
> + return -1;
> + }
> +
> + /* Set initrd_end */
> + initrd_base = simple_strtoul(initrd_addr_str, NULL, 16);
> + initrd_addr_r = (void *)initrd_base;
> + sprintf(initrd_end_str, "0x%lx", initrd_base + initrd_size - 1);
> + setenv("initrd_end", initrd_end_str);
> +
> + /* Load kernel to memory */
> + fdt_addr_r = (void *)simple_strtoul(fdt_addr_str, NULL, 16);
> + kernel_addr_r = (void *)simple_strtoul(kernel_addr_str, NULL, 16);
> +
> + /*
> + * The kernel must be lower in memory than fdt and loading the
> + * kernel must not trample the fdt or vice versa.
> + */
> + avail = fdt_addr_r - kernel_addr_r;
> + if (avail < 0) {
> + printf("%s: fdt must be after kernel\n", __func__);
> + return -1;
> + }
> + smh_load(kernel_name, kernel_addr_r, avail, 1);
> +
> + /* Load fdt to memory */
> + smh_load(fdt_name, fdt_addr_r, 0x20000, 1);
> +
> + /* Load initrd to memory */
> + smh_load(initrd_name, initrd_addr_r, initrd_size, 1);
> +
> +#endif /* CONFIG_SEMIHOSTING */
> + return 0;
> +}
> +#endif /* CONFIG_BOARD_LATE_INIT */
> +
> /*
> * Board specific ethernet initialization routine.
> */
> diff --git a/boards.cfg b/boards.cfg
> index 69c8936..d142b10 100644
> --- a/boards.cfg
> +++ b/boards.cfg
> @@ -44,6 +44,7 @@
>
> #########################################################################
> ##################################
>
> Active aarch64 armv8 - armltd
> vexpress64 vexpress_aemv8a
> vexpress_aemv8a:ARM64
> David Feng <fenghua at phytium.com.cn>
> +Active aarch64 armv8 - armltd
> vexpress64 vexpress_aemv8a_semi
> vexpress_aemv8a:ARM64,SEMIHOSTING,BASE_FVP
> Darwin Rambo <drambo at broadcom.com>
> Active arc arc700 - synopsys -
> axs101 -
> Alexey Brodkin <abrodkin at synopsys.com>
> Active arc arc700 - synopsys <none>
> arcangel4 -
> Alexey Brodkin <abrodkin at synopsys.com>
> Active arc arc700 - synopsys <none>
> arcangel4-be -
> Alexey Brodkin <abrodkin at synopsys.com>
> diff --git a/doc/README.semihosting b/doc/README.semihosting new file
> mode 100644 index 0000000..c999a27
> --- /dev/null
> +++ b/doc/README.semihosting
> @@ -0,0 +1,35 @@
> +/*
> + * Copyright 2014 Broadcom Corporation.
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +Semihosting is ARM's way of having a real or virtual target communicate
> +with a host or host debugger for basic operations such as file I/O,
> +console I/O, etc. Please see
> +http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0471c/Bgb
> jjgij.html for more information.
> +
> +For developing on armv8 virtual fastmodel platforms, semihosting is a
> +valuable tool since it allows access to image/configuration files
> +before eMMC or other NV media are available.
> +
> +For reference, the current example is enabled by setting
> +CONFIG_SEMIHOSTING for the "vexpress_aemv8a" board.
> +
> +We require that the board include file define these env variables:
> +- kernel_name e.g. "uImage"
> +- kernel_addr_r e.g. "0x80000000"
> +- initrd_name e.g. "ramdisk.img"
> +- initrd_addr_r e.g. "0x88000000"
> +- fdt_name e.g. "devtree.dtb"
> +- fdt_addr_r e.g. "0x83000000"
> +
> +Optionally, "fdt_high" and "initrd_high" can be specified as per their
> +rules for allowing or preventing copying of these images.
> +
> +For the "fdt chosen" startup macro, this code will then define:
> +- initrd_end (based on retrieving initrd_addr_r plus actual
> +initrd_size)
> +
> +We will then load the kernel, initrd, and fdt into the specified
> +locations in memory in a similar way that the ATF fastmodel code uses
> +semihosting calls to load other boot stages and u-boot itself.
> diff --git a/include/configs/vexpress_aemv8a.h
> b/include/configs/vexpress_aemv8a.h
> index e851702..96978f5 100644
> --- a/include/configs/vexpress_aemv8a.h
> +++ b/include/configs/vexpress_aemv8a.h
> @@ -10,6 +10,14 @@
>
> #define DEBUG
>
> +#ifdef CONFIG_BASE_FVP
> +#ifndef CONFIG_SEMIHOSTING
> +#error CONFIG_BASE_FVP requires CONFIG_SEMIHOSTING #endif #define
> +CONFIG_BOARD_LATE_INIT #define CONFIG_ARMV8_SWITCH_TO_EL1 #endif
> +
> #define CONFIG_REMAKE_ELF
>
> /*#define CONFIG_ARMV8_SWITCH_TO_EL1*/
> @@ -28,8 +36,14 @@
> #define CONFIG_BOOTP_VCI_STRING "U-boot.armv8.vexpress_aemv8a"
>
> /* Link Definitions */
> +#ifdef CONFIG_BASE_FVP
> +/* ATF loads u-boot here for BASE_FVP model */
> +#define CONFIG_SYS_TEXT_BASE 0x88000000
> +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE +
> 0x03f00000)
> +#else
> #define CONFIG_SYS_TEXT_BASE 0x80000000
> #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE +
> 0x7fff0)
> +#endif
>
> /* Flat Device Tree Definitions */
> #define CONFIG_OF_LIBFDT
> @@ -37,7 +51,11 @@
> #define CONFIG_DEFAULT_DEVICE_TREE vexpress64
>
> /* SMP Spin Table Definitions */
> +#ifdef CONFIG_BASE_FVP
> +#define CPU_RELEASE_ADDR (CONFIG_SYS_SDRAM_BASE + 0x03f00000)
> +#else
> #define CPU_RELEASE_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0)
> +#endif
>
> /* CS register bases for the original memory map. */
> #define V2M_PA_CS0 0x00000000
> @@ -93,8 +111,13 @@
> #define COUNTER_FREQUENCY (0x1800000) /* 24MHz */
>
> /* Generic Interrupt Controller Definitions */
> +#ifdef CONFIG_BASE_FVP
> +#define GICD_BASE (0x2f000000)
> +#define GICC_BASE (0x2c000000)
> +#else
> #define GICD_BASE (0x2C001000)
> #define GICC_BASE (0x2C002000)
> +#endif
>
> #define CONFIG_SYS_MEMTEST_START V2M_BASE
> #define CONFIG_SYS_MEMTEST_END (V2M_BASE + 0x80000000)
> @@ -114,7 +137,6 @@
> #define CONFIG_CONS_INDEX 0
>
> #define CONFIG_BAUDRATE 115200
> -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
> #define CONFIG_SYS_SERIAL0 V2M_UART0
> #define CONFIG_SYS_SERIAL1 V2M_UART1
>
> @@ -158,17 +180,41 @@
> #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
>
> /* Initial environment variables */
> +#ifdef CONFIG_BASE_FVP
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> + "kernel_name=uImage\0" \
> + "kernel_addr_r=0x80000000\0" \
> + "initrd_name=ramdisk.img\0" \
> + "initrd_addr_r=0x88000000\0" \
> + "fdt_name=devtree.dtb\0" \
> + "fdt_addr_r=0x83000000\0" \
> + "fdt_high=0xffffffffffffffff\0" \
> + "initrd_high=0xffffffffffffffff\0"
> +
> +#define CONFIG_BOOTARGS "console=ttyAMA0 earlyprintk=pl011,"\
> + "0x1c090000 debug user_debug=31 "\
> + "loglevel=9"
> +
> +#define CONFIG_BOOTCOMMAND "fdt addr $fdt_addr_r; fdt resize; " \
> + "fdt chosen $initrd_addr_r $initrd_end; " \
> + "bootm $kernel_addr_r - $fdt_addr_r"
> +
> +#define CONFIG_BOOTDELAY 1
> +
> +#else
> +
> #define CONFIG_EXTRA_ENV_SETTINGS \
> - "kernel_addr=0x200000\0" \
> - "initrd_addr=0xa00000\0" \
> + "kernel_addr_r=0x200000\0" \
> + "initrd_addr_r=0xa00000\0" \
> "initrd_size=0x2000000\0" \
> - "fdt_addr=0x100000\0" \
> + "fdt_addr_r=0x100000\0" \
> "fdt_high=0xa0000000\0"
>
> #define CONFIG_BOOTARGS "console=ttyAMA0
> root=/dev/ram0"
> -#define CONFIG_BOOTCOMMAND "bootm $kernel_addr " \
> - "$initrd_addr:$initrd_size $fdt_addr"
> +#define CONFIG_BOOTCOMMAND "bootm $kernel_addr_r " \
> + "$initrd_addr_r:$initrd_size $fdt_addr_r"
> #define CONFIG_BOOTDELAY -1
> +#endif
>
> /* Do not preserve environment */
> #define CONFIG_ENV_IS_NOWHERE 1
> @@ -180,7 +226,6 @@
> #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
> sizeof(CONFIG_SYS_PROMPT) + 16)
> #define CONFIG_SYS_HUSH_PARSER
> -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
> #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
> #define CONFIG_SYS_LONGHELP
> #define CONFIG_CMDLINE_EDITING 1
> --
> 1.7.9.5
>
>
More information about the U-Boot
mailing list