[U-Boot] [PATCH 2/2] arm: mx6: cm_fx6: use gpio request
Nikita Kiryanov
nikita at compulab.co.il
Thu Oct 2 16:17:24 CEST 2014
Use gpio_request for all the gpios that are utilized by various
subsystems in cm-fx6, and refactor the relevant init functions
so that all gpios are requested during board_init(), not during
subsystem init, thus avoiding the need to manage gpio ownership
each time a subsystem is initialized.
The new division of labor is:
During board_init() muxes are setup and gpios are requested.
During subsystem init gpios are toggled.
Cc: Igor Grinberg <grinberg at compulab.co.il>
Cc: Simon Glass <sjg at chromium.org>
Signed-off-by: Nikita Kiryanov <nikita at compulab.co.il>
---
board/compulab/cm_fx6/cm_fx6.c | 133 +++++++++++++++++++++++++++++------------
1 file changed, 94 insertions(+), 39 deletions(-)
diff --git a/board/compulab/cm_fx6/cm_fx6.c b/board/compulab/cm_fx6/cm_fx6.c
index 9c6e686..f0edc8f 100644
--- a/board/compulab/cm_fx6/cm_fx6.c
+++ b/board/compulab/cm_fx6/cm_fx6.c
@@ -69,16 +69,23 @@ static iomux_v3_cfg_t const sata_pads[] = {
IOMUX_PADS(PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
-static void cm_fx6_setup_issd(void)
+static int cm_fx6_setup_issd(void)
{
+ int ret, i;
+
SETUP_IOMUX_PADS(sata_pads);
- /* Make sure this gpio has logical 0 value */
- gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0);
- udelay(100);
- cm_fx6_sata_power(0);
- mdelay(250);
- cm_fx6_sata_power(1);
+ for (i = 0; i < ARRAY_SIZE(cm_fx6_issd_gpios); i++) {
+ ret = gpio_request(cm_fx6_issd_gpios[i], "sata");
+ if (ret)
+ return ret;
+ }
+
+ ret = gpio_request(CM_FX6_SATA_PWLOSS_INT, "sata_pwloss_int");
+ if (ret)
+ return ret;
+
+ return 0;
}
#define CM_FX6_SATA_INIT_RETRIES 10
@@ -86,7 +93,14 @@ int sata_initialize(void)
{
int err, i;
- cm_fx6_setup_issd();
+ /* Make sure this gpio has logical 0 value */
+ gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0);
+ udelay(100);
+
+ cm_fx6_sata_power(0);
+ mdelay(250);
+ cm_fx6_sata_power(1);
+
for (i = 0; i < CM_FX6_SATA_INIT_RETRIES; i++) {
err = setup_sata();
if (err) {
@@ -109,6 +123,8 @@ int sata_initialize(void)
return err;
}
+#else
+static int cm_fx6_setup_issd(void) { return 0; }
#endif
#ifdef CONFIG_SYS_I2C_MXC
@@ -177,35 +193,32 @@ static int cm_fx6_setup_i2c(void) { return 0; }
#define WEAK_PULLDOWN (PAD_CTL_PUS_100K_DOWN | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
PAD_CTL_HYS | PAD_CTL_SRE_SLOW)
+#define MX6_USBNC_BASEADDR 0x2184800
+#define USBNC_USB_H1_PWR_POL (1 << 9)
-static int cm_fx6_usb_hub_reset(void)
+static int cm_fx6_setup_usb_host(void)
{
int err;
err = gpio_request(CM_FX6_USB_HUB_RST, "usb hub rst");
- if (err) {
- printf("USB hub rst gpio request failed: %d\n", err);
- return -1;
- }
+ if (err)
+ return err;
+ SETUP_IOMUX_PAD(PAD_GPIO_0__USB_H1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL));
SETUP_IOMUX_PAD(PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL));
- gpio_direction_output(CM_FX6_USB_HUB_RST, 0);
- udelay(10);
- gpio_direction_output(CM_FX6_USB_HUB_RST, 1);
- mdelay(1);
return 0;
}
-static int cm_fx6_init_usb_otg(void)
+static int cm_fx6_setup_usb_otg(void)
{
- int ret;
+ int err;
struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
- ret = gpio_request(SB_FX6_USB_OTG_PWR, "usb-pwr");
- if (ret) {
- printf("USB OTG pwr gpio request failed: %d\n", ret);
- return ret;
+ err = gpio_request(SB_FX6_USB_OTG_PWR, "usb-pwr");
+ if (err) {
+ printf("USB OTG pwr gpio request failed: %d\n", err);
+ return err;
}
SETUP_IOMUX_PAD(PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL));
@@ -216,25 +229,27 @@ static int cm_fx6_init_usb_otg(void)
return gpio_direction_output(SB_FX6_USB_OTG_PWR, 0);
}
-#define MX6_USBNC_BASEADDR 0x2184800
-#define USBNC_USB_H1_PWR_POL (1 << 9)
int board_ehci_hcd_init(int port)
{
+ int ret;
u32 *usbnc_usb_uh1_ctrl = (u32 *)(MX6_USBNC_BASEADDR + 4);
- switch (port) {
- case 0:
- return cm_fx6_init_usb_otg();
- case 1:
- SETUP_IOMUX_PAD(PAD_GPIO_0__USB_H1_PWR |
- MUX_PAD_CTRL(NO_PAD_CTRL));
+ /* Only 1 host controller in use. port 0 is OTG & needs no attention */
+ if (port != 1)
+ return 0;
- /* Set PWR polarity to match power switch's enable polarity */
- setbits_le32(usbnc_usb_uh1_ctrl, USBNC_USB_H1_PWR_POL);
- return cm_fx6_usb_hub_reset();
- default:
- break;
- }
+ /* Set PWR polarity to match power switch's enable polarity */
+ setbits_le32(usbnc_usb_uh1_ctrl, USBNC_USB_H1_PWR_POL);
+ ret = gpio_direction_output(CM_FX6_USB_HUB_RST, 0);
+ if (ret)
+ return ret;
+
+ udelay(10);
+ ret = gpio_direction_output(CM_FX6_USB_HUB_RST, 1);
+ if (ret)
+ return ret;
+
+ mdelay(1);
return 0;
}
@@ -246,6 +261,9 @@ int board_ehci_power(int port, int on)
return 0;
}
+#else
+static int cm_fx6_setup_usb_otg(void) { return 0; }
+static int cm_fx6_setup_usb_host(void) { return 0; }
#endif
#ifdef CONFIG_FEC_MXC
@@ -340,12 +358,17 @@ static int handle_mac_address(void)
int board_eth_init(bd_t *bis)
{
- int res = handle_mac_address();
- if (res)
+ int err;
+
+ err = handle_mac_address();
+ if (err)
puts("No MAC address found\n");
SETUP_IOMUX_PADS(enet_pads);
/* phy reset */
+ err = gpio_request(CM_FX6_ENET_NRST, "enet_nrst");
+ if (err)
+ printf("Etnernet NRST gpio request failed: %d\n", err);
gpio_direction_output(CM_FX6_ENET_NRST, 0);
udelay(500);
gpio_set_value(CM_FX6_ENET_NRST, 1);
@@ -416,6 +439,16 @@ int board_mmc_init(bd_t *bis)
}
#endif
+#ifdef CONFIG_MXC_SPI
+int cm_fx6_setup_ecspi(void)
+{
+ cm_fx6_set_ecspi_iomux();
+ return gpio_request(CM_FX6_ECSPI_BUS0_CS0, "ecspi_bus0_cs0");
+}
+#else
+int cm_fx6_setup_ecspi(void) { return 0; }
+#endif
+
#ifdef CONFIG_OF_BOARD_SETUP
void ft_board_setup(void *blob, bd_t *bd)
{
@@ -436,6 +469,28 @@ int board_init(void)
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
cm_fx6_setup_gpmi_nand();
+ ret = cm_fx6_setup_ecspi();
+ if (ret)
+ printf("Warning: ECSPI setup failed: %d\n", ret);
+
+ ret = cm_fx6_setup_usb_otg();
+ if (ret)
+ printf("Warning: USB OTG setup failed: %d\n", ret);
+
+ ret = cm_fx6_setup_usb_host();
+ if (ret)
+ printf("Warning: USB host setup failed: %d\n", ret);
+
+ /*
+ * cm-fx6 may have iSSD not assembled and in this case it has
+ * bypasses for a (m)SATA socket on the baseboard. The socketed
+ * device is not controlled by those GPIOs. So just print a warning
+ * if the setup fails.
+ */
+ ret = cm_fx6_setup_issd();
+ if (ret)
+ printf("Warning: iSSD setup failed: %d\n", ret);
+
/* Warn on failure but do not abort boot */
ret = cm_fx6_setup_i2c();
if (ret)
--
1.9.1
More information about the U-Boot
mailing list