[U-Boot] [RFC PATCH 13/28] powerpc: remove motionpro support
Masahiro Yamada
yamada.masahiro at socionext.com
Thu Aug 13 12:15:31 CEST 2015
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro at socionext.com>
---
arch/powerpc/cpu/mpc5xxx/Kconfig | 4 -
board/motionpro/Kconfig | 9 -
board/motionpro/MAINTAINERS | 6 -
board/motionpro/Makefile | 8 -
board/motionpro/motionpro.c | 220 ----------------------
configs/motionpro_defconfig | 7 -
include/configs/motionpro.h | 390 ---------------------------------------
7 files changed, 644 deletions(-)
delete mode 100644 board/motionpro/Kconfig
delete mode 100644 board/motionpro/MAINTAINERS
delete mode 100644 board/motionpro/Makefile
delete mode 100644 board/motionpro/motionpro.c
delete mode 100644 configs/motionpro_defconfig
delete mode 100644 include/configs/motionpro.h
diff --git a/arch/powerpc/cpu/mpc5xxx/Kconfig b/arch/powerpc/cpu/mpc5xxx/Kconfig
index c7b6892..70018aa 100644
--- a/arch/powerpc/cpu/mpc5xxx/Kconfig
+++ b/arch/powerpc/cpu/mpc5xxx/Kconfig
@@ -18,9 +18,6 @@ config TARGET_A4M072
config TARGET_CM5200
bool "Support cm5200"
-config TARGET_MOTIONPRO
- bool "Support motionpro"
-
config TARGET_MUNICES
bool "Support munices"
@@ -64,7 +61,6 @@ source "board/a4m072/Kconfig"
source "board/cm5200/Kconfig"
source "board/ifm/o2dnt2/Kconfig"
source "board/intercontrol/digsy_mtc/Kconfig"
-source "board/motionpro/Kconfig"
source "board/munices/Kconfig"
source "board/phytec/pcm030/Kconfig"
source "board/tqc/tqm5200/Kconfig"
diff --git a/board/motionpro/Kconfig b/board/motionpro/Kconfig
deleted file mode 100644
index f624f6c..0000000
--- a/board/motionpro/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_MOTIONPRO
-
-config SYS_BOARD
- default "motionpro"
-
-config SYS_CONFIG_NAME
- default "motionpro"
-
-endif
diff --git a/board/motionpro/MAINTAINERS b/board/motionpro/MAINTAINERS
deleted file mode 100644
index 2f8b5cb..0000000
--- a/board/motionpro/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-MOTIONPRO BOARD
-#M: -
-S: Maintained
-F: board/motionpro/
-F: include/configs/motionpro.h
-F: configs/motionpro_defconfig
diff --git a/board/motionpro/Makefile b/board/motionpro/Makefile
deleted file mode 100644
index 898a384..0000000
--- a/board/motionpro/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2003-2007
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := motionpro.o
diff --git a/board/motionpro/motionpro.c b/board/motionpro/motionpro.c
deleted file mode 100644
index 4d0ebaa..0000000
--- a/board/motionpro/motionpro.c
+++ /dev/null
@@ -1,220 +0,0 @@
-/*
- * (C) Copyright 2003-2007
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * modified for Promess PRO - by Andy Joseph, andy at promessdev.com
- * modified for Promess PRO-Motion - by Robert McCullough, rob at promessdev.com
- * modified by Chris M. Tumas 6/20/06 Change CAS latency to 2 from 3
- * Also changed the refresh for 100MHz operation
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc5xxx.h>
-#include <miiphy.h>
-#include <libfdt.h>
-
-#if defined(CONFIG_STATUS_LED)
-#include <status_led.h>
-#endif /* CONFIG_STATUS_LED */
-
-/* Kollmorgen DPR initialization data */
-struct init_elem {
- unsigned long addr;
- unsigned len;
- char *data;
- } init_seq[] = {
- {0x500003F2, 2, "\x86\x00"}, /* HW parameter */
- {0x500003F0, 2, "\x00\x00"},
- {0x500003EC, 4, "\x00\x80\xc1\x52"}, /* Magic word */
- };
-
-/*
- * Initialize Kollmorgen DPR
- */
-static void kollmorgen_init(void)
-{
- unsigned i, j;
- vu_char *p;
-
- for (i = 0; i < sizeof(init_seq) / sizeof(struct init_elem); ++i) {
- p = (vu_char *)init_seq[i].addr;
- for (j = 0; j < init_seq[i].len; ++j)
- *(p + j) = *(init_seq[i].data + j);
- }
-
- printf("DPR: Kollmorgen DPR initialized\n");
-}
-
-
-/*
- * Early board initalization.
- */
-int board_early_init_r(void)
-{
- /* Now, when we are in RAM, disable Boot Chipselect and enable CS0 */
- *(vu_long *)MPC5XXX_ADDECR &= ~(1 << 25);
- *(vu_long *)MPC5XXX_ADDECR |= (1 << 16);
-
- /* Initialize Kollmorgen DPR */
- kollmorgen_init();
-
- return 0;
-}
-
-
-/*
- * Additional PHY intialization. After being reset in mpc5xxx_fec_init_phy(),
- * PHY goes into FX mode. To take it out of the FX mode and switch into
- * desired TX operation, one needs to clear the FX_SEL bit of Mode Control
- * Register.
- */
-void reset_phy(void)
-{
- unsigned short mode_control;
-
- miiphy_read("FEC", CONFIG_PHY_ADDR, 0x15, &mode_control);
- miiphy_write("FEC", CONFIG_PHY_ADDR, 0x15,
- mode_control & 0xfffe);
- return;
-}
-
-#ifndef CONFIG_SYS_RAMBOOT
-/*
- * Helper function to initialize SDRAM controller.
- */
-static void sdram_start(int hi_addr)
-{
- long hi_addr_bit = hi_addr ? 0x01000000 : 0;
-
- /* unlock mode register */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 |
- hi_addr_bit;
-
- /* precharge all banks */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 |
- hi_addr_bit;
-
- /* auto refresh */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 |
- hi_addr_bit;
-
- /* auto refresh, second time */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 |
- hi_addr_bit;
-
- /* set mode register */
- *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE;
-
- /* normal operation */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
-}
-#endif /* !CONFIG_SYS_RAMBOOT */
-
-
-/*
- * Initalize SDRAM - configure SDRAM controller, detect memory size.
- */
-phys_size_t initdram(int board_type)
-{
- ulong dramsize = 0;
-#ifndef CONFIG_SYS_RAMBOOT
- ulong test1, test2;
-
- /* According to AN3221 (MPC5200B SDRAM Initialization and
- * Configuration), the SDelay register must be written a value of
- * 0x00000004 as the first step of the SDRAM contorller configuration.
- */
- *(vu_long *)MPC5XXX_SDRAM_SDELAY = 0x04;
-
- /* configure SDRAM start/end for detection */
- *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001e; /* 2G at 0x0 */
- *(vu_long *)MPC5XXX_SDRAM_CS1CFG = 0x80000000; /* disabled */
-
- /* setup config registers */
- *(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
- *(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
-
- sdram_start(0);
- test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
- sdram_start(1);
- test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
- if (test1 > test2) {
- sdram_start(0);
- dramsize = test1;
- } else {
- dramsize = test2;
- }
-
- /* memory smaller than 1MB is impossible */
- if (dramsize < (1 << 20))
- dramsize = 0;
-
- /* set SDRAM CS0 size according to the amount of RAM found */
- if (dramsize > 0) {
- *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x13 +
- __builtin_ffs(dramsize >> 20) - 1;
- } else {
- *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
- }
-
- /* let SDRAM CS1 start right after CS0 and disable it */
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize;
-
-#else /* !CONFIG_SYS_RAMBOOT */
- /* retrieve size of memory connected to SDRAM CS0 */
- dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF;
- if (dramsize >= 0x13)
- dramsize = (1 << (dramsize - 0x13)) << 20;
- else
- dramsize = 0;
-#endif /* CONFIG_SYS_RAMBOOT */
-
- /* return total ram size */
- return dramsize;
-}
-
-
-int checkboard(void)
-{
- uchar rev = *(vu_char *)CPLD_REV_REGISTER;
- printf("Board: Promess Motion-PRO board (CPLD rev. 0x%02x)\n", rev);
- return 0;
-}
-
-
-#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, bd_t *bd)
-{
- ft_cpu_setup(blob, bd);
-
- return 0;
-}
-#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
-
-
-#if defined(CONFIG_STATUS_LED)
-void __led_init(led_id_t regaddr, int state)
-{
- *((vu_long *) regaddr) |= ENABLE_GPIO_OUT;
-
- if (state == STATUS_LED_ON)
- *((vu_long *) regaddr) |= LED_ON;
- else
- *((vu_long *) regaddr) &= ~LED_ON;
-}
-
-void __led_set(led_id_t regaddr, int state)
-{
- if (state == STATUS_LED_ON)
- *((vu_long *) regaddr) |= LED_ON;
- else
- *((vu_long *) regaddr) &= ~LED_ON;
-}
-
-void __led_toggle(led_id_t regaddr)
-{
- *((vu_long *) regaddr) ^= LED_ON;
-}
-#endif /* CONFIG_STATUS_LED */
diff --git a/configs/motionpro_defconfig b/configs/motionpro_defconfig
deleted file mode 100644
index 4d3f909..0000000
--- a/configs/motionpro_defconfig
+++ /dev/null
@@ -1,7 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_MOTIONPRO=y
-CONFIG_AUTOBOOT_KEYED=y
-CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n"
-CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b"
-# CONFIG_CMD_SETEXPR is not set
diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h
deleted file mode 100644
index 6dc84eb..0000000
--- a/include/configs/motionpro.h
+++ /dev/null
@@ -1,390 +0,0 @@
-/*
- * (C) Copyright 2003-2007
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * Based on Motion-PRO board config file by Robert McCullough, rob at promessinc.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-
-/* CPU and board */
-#define CONFIG_MPC5200 1 /* This is a MPC5200 CPU */
-#define CONFIG_MOTIONPRO 1 /* ... on Promess Motion-PRO board */
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-#define CONFIG_SYS_TEXT_BASE 0xfff00000
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BEDBUG
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
-#define CONFIG_NETCONSOLE 1 /* network console */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC 1
-#define CONFIG_MPC5xxx_FEC_MII100
-#define CONFIG_PHY_ADDR 0x2
-#define CONFIG_PHY_TYPE 0x79c874
-#define CONFIG_RESET_PHY_R 1
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY 2 /* autoboot after 2 seconds */
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
-/*
- * Default environment settings
- */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=motionpro\0" \
- "netmask=255.255.255.0\0" \
- "ipaddr=192.168.1.106\0" \
- "serverip=192.168.1.100\0" \
- "gatewayip=192.168.1.100\0" \
- "console=ttyPSC0,115200\0" \
- "u-boot_addr=400000\0" \
- "kernel_addr=400000\0" \
- "fdt_addr=700000\0" \
- "ramdisk_addr=800000\0" \
- "multi_image_addr=800000\0" \
- "rootpath=/opt/eldk-4.2/ppc_6xx\0" \
- "u-boot=/tftpboot/motionpro/u-boot.bin\0" \
- "bootfile=/tftpboot/motionpro/uImage\0" \
- "fdt_file=/tftpboot/motionpro/motionpro.dtb\0" \
- "ramdisk_file=/tftpboot/motionpro/uRamdisk\0" \
- "multi_image_file=kernel+initrd+dtb.img\0" \
- "load=tftp ${u-boot_addr} ${u-boot}\0" \
- "update=prot off fff00000 +${filesize};" \
- "era fff00000 +${filesize}; " \
- "cp.b ${u-boot_addr} fff00000 ${filesize};" \
- "prot on fff00000 +${filesize}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "fat_args=setenv bootargs root=/dev/sda rw\0" \
- "mtdids=nor0=ff000000.flash\0" \
- "mtdparts=ff000000.flash:13m(fs),2m(kernel),384k(uboot)," \
- "128k(env),128k(redund_env)," \
- "128k(dtb),128k(user_data)\0" \
- "addcons=setenv bootargs ${bootargs} console=${console}\0" \
- "addmtd=setenv bootargs ${bootargs} mtdparts=${mtdparts}\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:" \
- "${netmask}:${hostname}:${netdev}:off panic=1 " \
- "console=${console}\0" \
- "net_nfs=tftp ${kernel_addr} ${bootfile}; " \
- "tftp ${fdt_addr} ${fdt_file}; " \
- "run nfsargs addip addmtd; " \
- "bootm ${kernel_addr} - ${fdt_addr}\0" \
- "net_self=tftp ${kernel_addr} ${bootfile}; " \
- "tftp ${fdt_addr} ${fdt_file}; " \
- "tftp ${ramdisk_addr} ${ramdisk_file}; " \
- "nfs ${ramdisk_addr} ${serverip}:${rootpath}/images/uRamdisk; " \
- "run ramargs addip addcons addmtd; " \
- "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
- "fat_multi=run fat_args addip addmtd; fatload ide 0:1 " \
- "${multi_image_addr} ${multi_image_file}; " \
- "bootm ${multi_image_addr}\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run fat_multi"
-
-/*
- * do board-specific init
- */
-#define CONFIG_BOARD_EARLY_INIT_R 1
-
-/*
- * Low level configuration
- */
-
-/*
- * Clock configuration: SYS_XTALIN = 33MHz
- */
-#define CONFIG_SYS_MPC5XXX_CLKIN 33000000
-
-/*
- * Set IPB speed to 100MHz
- */
-#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK
-
-/*
- * Memory map
- */
-/*
- * Warning!!! with the current BestComm Task, MBAR MUST BE set to 0xf0000000.
- * Setting MBAR to otherwise will cause system hang when using SmartDMA such
- * as network commands.
- */
-#define CONFIG_SYS_MBAR 0xf0000000
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-
-/*
- * If building for running out of SDRAM, then MBAR has been set up beforehand
- * (e.g., by the BDI). Otherwise we must specify the default boot-up value of
- * MBAR, as given in the doccumentation.
- */
-#if CONFIG_SYS_TEXT_BASE == 0x00100000
-#define CONFIG_SYS_DEFAULT_MBAR 0xf0000000
-#else /* CONFIG_SYS_TEXT_BASE != 0x00100000 */
-#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
-#define CONFIG_SYS_LOWBOOT 1
-#endif /* CONFIG_SYS_TEXT_BASE == 0x00100000 */
-
-/* Use SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
-#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT 1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* 384 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (1024 << 10) /* 1 MiB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* initial mem map for Linux */
-
-/*
- * Chip selects configuration
- */
-/* Boot Chipselect */
-#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_BOOTCS_CFG 0x00045D00
-
-/* Flash memory addressing */
-#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_CS0_CFG CONFIG_SYS_BOOTCS_CFG
-
-/* Dual Port SRAM -- Kollmorgen Drive memory addressing */
-#define CONFIG_SYS_CS1_START 0x50000000
-#define CONFIG_SYS_CS1_SIZE 0x10000
-#define CONFIG_SYS_CS1_CFG 0x05055800
-
-/* Local register access */
-#define CONFIG_SYS_CS2_START 0x50010000
-#define CONFIG_SYS_CS2_SIZE 0x10000
-#define CONFIG_SYS_CS2_CFG 0x05055800
-
-/* Anybus CompactCom Module memory addressing */
-#define CONFIG_SYS_CS3_START 0x50020000
-#define CONFIG_SYS_CS3_SIZE 0x10000
-#define CONFIG_SYS_CS3_CFG 0x05055800
-
-/* No burst and dead cycle = 2 for all CSs */
-#define CONFIG_SYS_CS_BURST 0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE 0x22222222
-
-/*
- * SDRAM configuration
- */
-/* 2 x MT48LC16M16A2BG-75 IT:D, CASL 3, 32 bit data bus */
-#define SDRAM_CONFIG1 0x62322900
-#define SDRAM_CONFIG2 0x88c70000
-#define SDRAM_CONTROL 0x504f0000
-#define SDRAM_MODE 0x00cd0000
-
-/*
- * Flash configuration
- */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1
-#define CONFIG_SYS_FLASH_BASE 0xff000000
-#define CONFIG_SYS_FLASH_SIZE 0x01000000
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */
-#define CONFIG_FLASH_16BIT /* Flash is 16-bit */
-
-/*
- * MTD configuration
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=motionpro-0"
-#define MTDPARTS_DEFAULT "mtdparts=motionpro-0:" \
- "13m(fs),2m(kernel),384k(uboot)," \
- "128k(env),128k(redund_env)," \
- "128k(dtb),-(user_data)"
-
-/*
- * IDE/ATA configuration
- */
-#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
-#define CONFIG_SYS_IDE_MAXBUS 1
-#define CONFIG_SYS_IDE_MAXDEVICE 1
-#define CONFIG_IDE_PREINIT
-
-#define CONFIG_SYS_ATA_DATA_OFFSET 0x0060
-#define CONFIG_SYS_ATA_REG_OFFSET CONFIG_SYS_ATA_DATA_OFFSET
-#define CONFIG_SYS_ATA_STRIDE 4
-#define CONFIG_DOS_PARTITION
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* select I2C module #2 */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 1 /* 2 bytes per write cycle */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 /* 2ms/cycle + 3ms extra */
-#define CONFIG_SYS_I2C_MULTI_EEPROMS 1 /* 2 EEPROMs (addr:50,52) */
-
-/*
- * RTC configuration
- */
-#define CONFIG_RTC_DS1337 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-
-/*
- * Status LED configuration
- */
-#define CONFIG_STATUS_LED /* Status LED enabled */
-#define CONFIG_BOARD_SPECIFIC_LED
-
-#define ENABLE_GPIO_OUT 0x00000024
-#define LED_ON 0x00000010
-
-#ifndef __ASSEMBLY__
-/*
- * In case of Motion-PRO, a LED is identified by its corresponding
- * GPT Enable and Mode Select Register.
- */
-typedef volatile unsigned long * led_id_t;
-
-extern void __led_init(led_id_t id, int state);
-extern void __led_toggle(led_id_t id);
-extern void __led_set(led_id_t id, int state);
-#endif /* __ASSEMBLY__ */
-
-/*
- * Temperature sensor
- */
-#define CONFIG_DTT_LM75 1
-#define CONFIG_DTT_SENSORS { 0x49 }
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-/* This has to be a multiple of the Flash sector size */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_SIZE 0x1000
-#define CONFIG_ENV_SECT_SIZE 0x20000
-
-/* Configuration of redundant environment */
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-/*
- * Pin multiplexing configuration
- */
-
-/* PSC1: UART1
- * PSC2: GPIO (default)
- * PSC3: GPIO (default)
- * USB: 2xUART4/5
- * Ethernet: Ethernet 100Mbit with MD
- * Timer: CAN2/GPIO
- * PSC6/IRDA: GPIO (default)
- */
-#define CONFIG_SYS_GPS_PORT_CONFIG 0x1105a004
-
-/*
- * Motion-PRO's CPLD revision control register
- */
-#define CPLD_REV_REGISTER (CONFIG_SYS_CS2_START + 0x06)
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x03e00000 /* 1 ... 62 MiB in DRAM */
-#define CONFIG_SYS_ALT_MEMTEST
-
-#define CONFIG_SYS_LOAD_ADDR 0x200000 /* default kernel load addr */
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL HID0_ICE
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-
-/* Not needed for MPC 5xxx U-Boot, but used by tools/updater */
-#define CONFIG_SYS_RESET_ADDRESS 0xfff00100
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
-#define OF_CPU "PowerPC,5200 at 0"
-#define OF_SOC "soc5200 at f0000000"
-#define OF_TBCLK (bd->bi_busfreq / 4)
-#define OF_STDOUT_PATH "/soc5200 at f0000000/serial at 2000"
-
-#endif /* __CONFIG_H */
--
1.9.1
More information about the U-Boot
mailing list