[U-Boot] [PATCH 1/2][v4] powerpc/mpc85xx: SECURE BOOT- NAND secure boot target for P3041
Aneesh Bansal
aneesh.bansal at freescale.com
Wed Feb 25 09:47:56 CET 2015
Secure Boot Target is added for NAND for P3041.
Changes:
In PowerPC, the core begins execution from address 0xFFFFFFFC.
In case of secure boot, this default address maps to Boot ROM.
The Boot ROM code requires that the bootloader(U-boot) must lie
in 0 to 3.5G address space i.e. 0x0 - 0xDFFFFFFF.
In case of NAND Secure Boot, CONFIG_SYS_RAMBOOT is enabled and CPC is
configured as SRAM. U-Boot binary will be located on this SRAM at
location 0xBFF40000 with entry point as 0xBFFFFFFC.
Signed-off-by: Ruchika Gupta <ruchika.gupta at freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal at freescale.com>
---
Changes in v4:
- Created a patch set.
Makefile | 4 ++++
arch/powerpc/cpu/mpc85xx/cpu_init.c | 17 +++++++++++++++++
board/freescale/common/p_corenet/tlb.c | 18 +++++++++++++++++-
board/freescale/corenet_ds/MAINTAINERS | 5 +++++
configs/P3041DS_NAND_SECURE_BOOT_defconfig | 4 ++++
include/configs/corenet_ds.h | 9 +++++++++
6 files changed, 56 insertions(+), 1 deletion(-)
create mode 100644 configs/P3041DS_NAND_SECURE_BOOT_defconfig
diff --git a/Makefile b/Makefile
index bd4abab..acfaa23 100644
--- a/Makefile
+++ b/Makefile
@@ -719,8 +719,12 @@ ALL-$(CONFIG_ONENAND_U_BOOT) += u-boot-onenand.bin
ifeq ($(CONFIG_SPL_FSL_PBL),y)
ALL-$(CONFIG_RAMBOOT_PBL) += u-boot-with-spl-pbl.bin
else
+ifneq ($(CONFIG_SECURE_BOOT), y)
+# For Secure Boot The Image needs to be signed and Header must also
+# be included. So The image has to be built explicitly
ALL-$(CONFIG_RAMBOOT_PBL) += u-boot.pbl
endif
+endif
ALL-$(CONFIG_SPL) += spl/u-boot-spl.bin
ALL-$(CONFIG_SPL_FRAMEWORK) += u-boot.img
ALL-$(CONFIG_TPL) += tpl/u-boot-tpl.bin
diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init.c b/arch/powerpc/cpu/mpc85xx/cpu_init.c
index 4cf8853..ef56cc0 100644
--- a/arch/powerpc/cpu/mpc85xx/cpu_init.c
+++ b/arch/powerpc/cpu/mpc85xx/cpu_init.c
@@ -843,6 +843,23 @@ int cpu_init_r(void)
setup_mp();
#endif
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) && \
+ defined(CONFIG_SECURE_BOOT)
+ /* Disable the TLB Created for L3 and create the TLB required for
+ * PCIE (CONFIG_SYS_PCIE1_MEM_VIRT) which was not created earlier.
+ */
+ int tlb_index;
+ tlb_index = find_tlb_idx((void *)CONFIG_BPTR_VIRT_ADDR, 1);
+ if (tlb_index != -1) {
+ disable_tlb(tlb_index);
+
+ set_tlb(1, CONFIG_SYS_PCIE1_MEM_VIRT,
+ CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, tlb_index, BOOKE_PAGESZ_1G, 1);
+ }
+#endif
+
#ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC13
{
if (SVR_MAJ(svr) < 3) {
diff --git a/board/freescale/common/p_corenet/tlb.c b/board/freescale/common/p_corenet/tlb.c
index 8148e46..1b60cfb 100644
--- a/board/freescale/common/p_corenet/tlb.c
+++ b/board/freescale/common/p_corenet/tlb.c
@@ -42,7 +42,9 @@ struct fsl_e_tlb_entry tlb_table[] = {
/* TLB 1 */
/* *I*** - Covers boot page */
-#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
+ /* In Case of Secure RAM Boot L3 address is defined at 0xbff00000 */
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) && \
+ !defined(CONFIG_SECURE_BOOT)
/*
* *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the
* SRAM is at 0xfff00000, it covered the 0xfffff000.
@@ -76,11 +78,25 @@ struct fsl_e_tlb_entry tlb_table[] = {
MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
0, 2, BOOKE_PAGESZ_256M, 1),
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) && \
+ defined(CONFIG_SECURE_BOOT)
+ /* In case of Secure Boot, L3 is used as 1M SRAM
+ * and the address of the SRAM is at 0xbff00000.
+ * The PCIE TLB entry conflicts with the above entry.
+ * So, the entry for PCIE is not created at this point of time.
+ * It will be created later on in cpu_init_r()
+ * when U-Boot has relocated to DDR
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_1M, 1),
+#else
/* *I*G* - PCI */
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 3, BOOKE_PAGESZ_1G, 1),
+#endif
/* *I*G* - PCI */
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x40000000,
CONFIG_SYS_PCIE1_MEM_PHYS + 0x40000000,
diff --git a/board/freescale/corenet_ds/MAINTAINERS b/board/freescale/corenet_ds/MAINTAINERS
index 745847c..6855446 100644
--- a/board/freescale/corenet_ds/MAINTAINERS
+++ b/board/freescale/corenet_ds/MAINTAINERS
@@ -28,3 +28,8 @@ F: configs/P5040DS_NAND_defconfig
F: configs/P5040DS_SDCARD_defconfig
F: configs/P5040DS_SPIFLASH_defconfig
F: configs/P5040DS_SECURE_BOOT_defconfig
+
+CORENET_DS_SECURE_BOOT BOARD
+M: Aneesh Bansal <aneesh.bansal at freescale.com>
+S: Maintained
+F: configs/P3041DS_NAND_SECURE_BOOT_defconfig
diff --git a/configs/P3041DS_NAND_SECURE_BOOT_defconfig b/configs/P3041DS_NAND_SECURE_BOOT_defconfig
new file mode 100644
index 0000000..e810b1c
--- /dev/null
+++ b/configs/P3041DS_NAND_SECURE_BOOT_defconfig
@@ -0,0 +1,4 @@
+CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,NAND,SECURE_BOOT,SYS_TEXT_BASE=0xBFF40000"
+CONFIG_PPC=y
+CONFIG_MPC85xx=y
+CONFIG_TARGET_P3041DS=y
diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h
index 225ffdd..64c6890 100644
--- a/include/configs/corenet_ds.h
+++ b/include/configs/corenet_ds.h
@@ -16,6 +16,14 @@
#include "../board/freescale/common/ics307_clk.h"
#ifdef CONFIG_RAMBOOT_PBL
+#ifdef CONFIG_SECURE_BOOT
+#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS 0xbffffffc
+#define CONFIG_BPTR_VIRT_ADDR 0xbffff000
+#ifdef CONFIG_NAND
+#define CONFIG_RAMBOOT_NAND
+#endif
+#else
#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
#define CONFIG_SYS_FSL_PBL_PBI board/freescale/corenet_ds/pbi.cfg
@@ -29,6 +37,7 @@
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/corenet_ds/rcw_p5040ds.cfg
#endif
#endif
+#endif
#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
/* Set 1M boot space */
--
1.8.1.4
More information about the U-Boot
mailing list