[U-Boot] [PATCH v2] sunxi: power: add support for sy8106a driver
Hans de Goede
hdegoede at redhat.com
Tue Feb 23 20:42:12 CET 2016
Hi,
On 02/23/2016 06:47 PM, Jelle van der Waa wrote:
> SY8106A is a PMIC which is used on the Allwinner
> H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is
> implemented to set the default V-CPU voltage to 1200 mV.
>
> This driver is required to retain the SY8106A V-CPU
> voltage after a software reset. On cold boot the default
> SY8106A output voltage is selected by a pair of resistors
> and happens to be 1.2V on the Orange Pi PC and Plus.
>
> Signed-off-by: Jelle van der Waa <jelle at vdwaa.nl>
> Signed-off-by: Hans de Goede <hdegoede at redhat.com>
> Tested-by: Siarhei Siamashka <siarhei.siamashka at gmail.com>
> Acked-by: Siarhei Siamashka <siarhei.siamashka at gmail.com>
>
> ---
> Changes in v2
> - Fixed typo in commit message thea => the.
> - Made config R_I2C_ENABLE depend on SY8106A_POWER.
> - Removed 'default n' from config R_I2C_ENABLE
> - Changed SY8106A_POWER description from "most" to "some" boards.
> - Added license/copyright to include/sy8106a.h and
> drivers/power/sy8106a.c.
Thanks, I've merged this (with a slightly improved commit msg)
into my tree and it will be part of my next pull-req.
Regards,
Hans
> ---
> board/sunxi/Kconfig | 5 ++++-
> board/sunxi/board.c | 5 +++++
> configs/orangepi_pc_defconfig | 2 +-
> drivers/power/Kconfig | 16 ++++++++++++++++
> drivers/power/Makefile | 1 +
> drivers/power/sy8106a.c | 29 +++++++++++++++++++++++++++++
> include/configs/sunxi-common.h | 6 ++++--
> include/sy8106a.h | 11 +++++++++++
> 8 files changed, 71 insertions(+), 4 deletions(-)
> create mode 100644 drivers/power/sy8106a.c
> create mode 100644 include/sy8106a.h
>
> diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig
> index a334aa3..5e9d3af 100644
> --- a/board/sunxi/Kconfig
> +++ b/board/sunxi/Kconfig
> @@ -372,11 +372,14 @@ config I2C3_ENABLE
> See I2C0_ENABLE help text.
> endif
>
> +if SUNXI_GEN_SUN6I
> config R_I2C_ENABLE
> bool "Enable the PRCM I2C/TWI controller"
> - default n
> + # This is used for the pmic on H3
> + default y if SY8106A_POWER
> ---help---
> Set this to y to enable the I2C controller which is part of the PRCM.
> +endif
>
> if MACH_SUN7I
> config I2C4_ENABLE
> diff --git a/board/sunxi/board.c b/board/sunxi/board.c
> index 420481a..15b7af6 100644
> --- a/board/sunxi/board.c
> +++ b/board/sunxi/board.c
> @@ -25,6 +25,7 @@
> #include <asm/io.h>
> #include <nand.h>
> #include <net.h>
> +#include <sy8106a.h>
>
> #if defined CONFIG_VIDEO_LCD_PANEL_I2C && !(defined CONFIG_SPL_BUILD)
> /* So that we can use pin names in Kconfig and sunxi_name_to_gpio() */
> @@ -436,6 +437,10 @@ void sunxi_board_init(void)
> int power_failed = 0;
> unsigned long ramsize;
>
> +#ifdef CONFIG_SY8106A_POWER
> + power_failed = sy8106a_set_vout1(CONFIG_SY8106A_VOUT1_VOLT);
> +#endif
> +
> #if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || \
> defined CONFIG_AXP221_POWER || defined CONFIG_AXP818_POWER
> power_failed = axp_init();
> diff --git a/configs/orangepi_pc_defconfig b/configs/orangepi_pc_defconfig
> index ea9ed87..29a8da6 100644
> --- a/configs/orangepi_pc_defconfig
> +++ b/configs/orangepi_pc_defconfig
> @@ -12,4 +12,4 @@ CONFIG_SPL=y
> # CONFIG_CMD_FLASH is not set
> # CONFIG_CMD_FPGA is not set
> CONFIG_CMD_GPIO=y
> -CONFIG_R_I2C_ENABLE=y
> +CONFIG_SY8106A_POWER=y
> diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
> index 10683a2..adc6455 100644
> --- a/drivers/power/Kconfig
> +++ b/drivers/power/Kconfig
> @@ -48,6 +48,13 @@ config AXP818_POWER
> Say y here to enable support for the axp818 pmic found on
> A83T dev board.
>
> +config SY8106A_POWER
> + boolean "SY8106A pmic support"
> + depends on MACH_SUN8I_H3
> + ---help---
> + Select this to enable support for the SY8106A pmic found on some
> + H3 boards.
> +
> endchoice
>
> config AXP_DCDC1_VOLT
> @@ -232,4 +239,13 @@ config AXP_ELDO3_VOLT
> 1.2V for the SSD2828 chip (converter of parallel LCD interface
> into MIPI DSI).
>
> +config SY8106A_VOUT1_VOLT
> + int "SY8106A pmic VOUT1 voltage"
> + depends on SY8106A_POWER
> + default 1200
> + ---help---
> + Set the voltage (mV) to program the SY8106A pmic VOUT1. This
> + is typically used to power the VDD-CPU and should be 1200mV.
> + Values can range from 680mV till 1950mV.
> +
> endmenu
> diff --git a/drivers/power/Makefile b/drivers/power/Makefile
> index 0fdbca3..690faa0 100644
> --- a/drivers/power/Makefile
> +++ b/drivers/power/Makefile
> @@ -12,6 +12,7 @@ obj-$(CONFIG_AXP221_POWER) += axp221.o
> obj-$(CONFIG_AXP818_POWER) += axp818.o
> obj-$(CONFIG_EXYNOS_TMU) += exynos-tmu.o
> obj-$(CONFIG_FTPMU010_POWER) += ftpmu010.o
> +obj-$(CONFIG_SY8106A_POWER) += sy8106a.o
> obj-$(CONFIG_TPS6586X_POWER) += tps6586x.o
> obj-$(CONFIG_TWL4030_POWER) += twl4030.o
> obj-$(CONFIG_TWL6030_POWER) += twl6030.o
> diff --git a/drivers/power/sy8106a.c b/drivers/power/sy8106a.c
> new file mode 100644
> index 0000000..bbf116f
> --- /dev/null
> +++ b/drivers/power/sy8106a.c
> @@ -0,0 +1,29 @@
> +/*
> + * (C) Copyright 2016
> + * Jelle van der Waa <jelle at vdwaa.nl>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +#include <common.h>
> +#include <i2c.h>
> +#include <sy8106a.h>
> +
> +#define SY8106A_I2C_ADDR 0x65
> +#define SY8106A_VOUT1_SEL 1
> +#define SY8106A_VOUT1_SEL_ENABLE (1 << 7)
> +
> +static u8 sy8106a_mvolt_to_cfg(int mvolt, int min, int max, int div)
> +{
> + if (mvolt < min)
> + mvolt = min;
> + else if (mvolt > max)
> + mvolt = max;
> +
> + return (mvolt - min) / div;
> +}
> +
> +int sy8106a_set_vout1(unsigned int mvolt)
> +{
> + u8 data = sy8106a_mvolt_to_cfg(mvolt, 680, 1950, 10) | SY8106A_VOUT1_SEL_ENABLE;
> + return i2c_write(SY8106A_I2C_ADDR, SY8106A_VOUT1_SEL, 1, &data, 1);
> +}
> diff --git a/include/configs/sunxi-common.h b/include/configs/sunxi-common.h
> index b4dfb3c..40850e5 100644
> --- a/include/configs/sunxi-common.h
> +++ b/include/configs/sunxi-common.h
> @@ -206,7 +206,8 @@
> #define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
>
> /* I2C */
> -#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER
> +#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || \
> + defined CONFIG_SY8106A_POWER
> #define CONFIG_SPL_I2C_SUPPORT
> #endif
>
> @@ -240,7 +241,8 @@ extern int soft_i2c_gpio_scl;
>
> /* PMU */
> #if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || \
> - defined CONFIG_AXP221_POWER || defined CONFIG_AXP818_POWER
> + defined CONFIG_AXP221_POWER || defined CONFIG_AXP818_POWER || \
> + defined CONFIG_SY8106A_POWER
> #define CONFIG_SPL_POWER_SUPPORT
> #endif
>
> diff --git a/include/sy8106a.h b/include/sy8106a.h
> new file mode 100644
> index 0000000..32e8c43
> --- /dev/null
> +++ b/include/sy8106a.h
> @@ -0,0 +1,11 @@
> +/*
> + * (C) Copyright 2016
> + * Jelle van der Waa <jelle at vdwaa.nl>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +#ifndef _SY8106A_PMIC_H_
> +
> +int sy8106a_set_vout1(unsigned int mvolt);
> +
> +#endif
>
More information about the U-Boot
mailing list