[U-Boot] Antwort: Re: QSPI "sf probe ...", "sf read ..." on Altera SoC FPGA

[Clément Péron]

Hi,

I got also somme issue with my QSPI on CycmoneV and u-boot 2017.07
I cherry-picked commits from  Jason Rush :
b90ce1c29023abe730d2b4174294bdc09acef3e0
836a0278476be94c95ff084f81c2302fc5c0265c
b0eac7e0d1e4817388543b58d30b322d0bac49a8

Also i forgot to put the
"u-boot,dm-pre-reloc;" in my device tree in the qspi node.

Now my QSPI is working fine except the sf unlock / lock
I have remove the "clear BP# bits" in the mtd/spi/spi_flash.c

Hope this can help you

Regards,
Clement

2017-09-06 8:10 GMT+02:00 Hannes Schmelzer <hannes at schmelzer.or.at>:
> Hi Jagan,
>
>
> On 09/04/2017 08:22 AM, Hannes Schmelzer wrote:
>>
>> "U-Boot" <u-boot-bounces at lists.denx.de> schrieb am 01.09.2017 16:39:03:
>> <hannes at schmelzer.or.at> wrote:
>>>>
>>>> Hi Eldor,
>>>>
>>>> just found your post in the mailinglist.
>>>>
>>>> https://lists.denx.de/pipermail/u-boot/2016-December/276491.html
>>>>
>>>> Reason why i'm searched there is, that i've now excactly same problem
>>
>> as
>>>>
>>>> you.
>>>
>>> Can you give some details, issue came-up while 'sf probe' or 'sf read' ?
>>
>> Hi Jagan,
>> please have a look into the weblink to the denx mailing list server.
>> I have basically same trouble as eldor reported the days ago.
>>
>> A simple 'sf probe' ends up in a
>> ### ERROR ### Please RESET the board ###
>> Interesting detail is, that the information about the flash (type, size,
>> ...) is printed out quite before the "hang".
>>
>> On wednesday i have the next time-slot to access the socfpga devkit board.
>> So i could bring in more details if necessary.
>
> as told few days ago, i've now again access to my socfpga devkit board.
> Here comes the console output:
>
> ---
> U-Boot SPL 2017.09-rc4-00023-g84a4206 (Sep 06 2017 - 08:02:35)
> /home/schmelzerh/work/u-boot/drivers/ddr/altera/sequencer.c: Preparing to
> start memory calibration
> /home/schmelzerh/work/u-boot/drivers/ddr/altera/sequencer.c: CALIBRATION
> PASSED
> /home/schmelzerh/work/u-boot/drivers/ddr/altera/sequencer.c: Calibration
> complete
> Trying to boot from MMC1
> spl: partition error
>
>
> U-Boot 2017.09-rc4-00023-g84a4206 (Sep 06 2017 - 08:02:35 +0200)
>
> CPU:   Altera SoCFPGA Platform
> FPGA:  Altera Cyclone V, SE/A6 or SX/C6 or ST/D6, version 0x0
> BOOT:  SD/MMC Internal Transceiver (3.0V)
>        Watchdog enabled
> I2C:   ready
> DRAM:  1 GiB
> MMC:   dwmmc0 at ff704000: 0
> *** Warning - bad CRC, using default environment
>
> In:    serial
> Out:   serial
> Err:   serial
> Model: Altera SOCFPGA Cyclone V SoC Development Kit
> Net:
> Error: ethernet at ff702000 address not set.
> No ethernet found.
> Hit any key to stop autoboot:  0
> => sf probe
> SF: Detected n25q512 with page size 256 Bytes, erase size 64 KiB, total 64
> MiB
> ### ERROR ### Please RESET the board ###
> ----
>
> Afterwards the board does some reset (about 20sec. later).
>
>
> cheers,
> Hannes
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot