[U-Boot] [PATCH 0/7] Remove defines for SPI default speed and mode

Simon Goldschmidt simon.k.r.goldschmidt at gmail.com
Mon Dec 10 19:20:29 UTC 2018


Am 10.12.2018 um 16:42 schrieb Adam Ford:
> On Mon, Dec 10, 2018 at 4:54 AM Patrick Delaunay
> <patrick.delaunay at st.com> wrote:
>>
>>
>> This patch-set finish (after the last Simmon comment)
>> and depends on the previous serie named:
>> "Read default speed and mode values from DT"
>>
>> http://patchwork.ozlabs.org/project/uboot/list/?series=76834
>>
>> This patchset remove the unnecessary defines for SPI speed and mode
>> when DM mode is used for SPI (CONFIG_DM_SPI_FLASH).
>>
>> Build result is available for the serie in gihub and travis:
>> https://github.com/patrickdelaunay/u-boot/tree/topic/spi
>> https://travis-ci.org/patrickdelaunay/u-boot/branches
>>
>>
> After applying both of your patches, the da850evm no longer boots from
> SPI flash.

I just did test this and it worked for me. Booting from QSPI on 
socfpga_socrates and loading something in U-Boot via sf probe/sf read, so:
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt at gmail.com>

> 
> U-Boot SPL 2019.01-rc1-00754-g21fb8c41b1 (Dec 10 2018 - 09:02:28 -0600)
> Trying to boot from SPI
> Warning: SPI speed fallback to 100 kHz
> 
> [repeat in perpetuity]
> 
> U-Boot SPL 2019.01-rc1-00754-g21fb8c41b1 (Dec 10 2018 - 09:02:28 -0600)
> Trying to boot from SPI
> Warning: SPI speed fallback to 100 kHz
> 
> I then tried to apply the first patch, and it also fails booting.
> 
> I'll reply to the original series with a similar message.  Looking at
> the comments, it looks like the code is assuming the DM_SPI_FLASH
> means DT when in reality, the da850evm's SPL is using platdata.  I
> looked at the platdata structure and I didn't see entries for SPI mode
> or speed.  However, I cannot prove this is the issue on the da850evm
> without diving into it a bit more.

Adam, from reading the da850-emv.dts and its '-u-boot.dtsi', it seems 
the fdtgrep indicators to keep the flash for the SPL dts are missing 
(compare to socfpga_cyclone5_socrates-u-boot.dtsi). In this case, the 
code does not find a flash node.

The same would of course apply when using platdata.

Regards,
Simon

> 
> adam
>>
>> Patrick Delaunay (7):
>>    spi: update management of default speed and mode
>>    spi: add comment for spi_flash_probe_bus_cs function
>>    da850evm: sf: Read default speed and mode values from DT
>>    dfu: sf: Read default speed and mode values from DT
>>    mips: mt76xx: gardena-smart-gateway: Read default speed and mode
>>      values from DT
>>    env: Read default speed and mode values from DT
>>    spi: remove define for SPI default SPEED and MODE
>>
>>   board/davinci/da8xxevm/da850evm.c          |  7 +++++++
>>   board/gardena/smart-gateway-mt7688/board.c | 24 ++++++++++++++++++++----
>>   cmd/sf.c                                   | 10 ++++++----
>>   common/spl/spl_spi.c                       | 11 ++++++-----
>>   common/splash_source.c                     | 11 ++++++-----
>>   drivers/dfu/dfu_sf.c                       | 10 ++++++++--
>>   env/Kconfig                                |  4 ++--
>>   env/sf.c                                   |  5 ++++-
>>   include/spi_flash.h                        | 18 ++++++++++++++++++
>>   9 files changed, 77 insertions(+), 23 deletions(-)
>>
>> --
>> 2.7.4
>>



More information about the U-Boot mailing list