[U-Boot] [PATCH v8 10/11] ls1088a: Add VID support for QDS and RDB platforms
Rajesh Bhagat
rajesh.bhagat at nxp.com
Wed Jan 17 10:43:09 UTC 2018
This patch adds the support for VID on LS1088AQDS and LS1088ARDB systems.
It reads the fusesr register and changes the VDD accordingly by adjusting
the voltage via LTC3882 regulator.
This patch also takes care of the special case of 0.9V VDD is present in
fusesr register. In that case,it also changes the SERDES voltage by
disabling the SERDES, changing the SVDD and then re-enabling SERDES.
Signed-off-by: Raghav Dogra <raghav.dogra at nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar at nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari at nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat at nxp.com>
---
Changes in v8:
- Added blank line before return
Changes in v7:
- Defined CONFIG_VID in SPL scenario too
- Defined new API init_func_vid for core voltage adjustment for LS1088A
Changes in v6:
None
Changes in v5:
None
Changes in v4:
None
Changes in v3:
Restructured LS1088A VID support to use common VID driver
Removed APIs getLSB/MSB and used bit operations.
Changes in v2:
Checkpatch errors fixed
board/freescale/ls1088a/ls1088a.c | 127 +++++++++++++++++++++++++++++++++++++-
include/configs/ls1088aqds.h | 11 ++++
include/configs/ls1088ardb.h | 12 ++++
3 files changed, 150 insertions(+)
diff --git a/board/freescale/ls1088a/ls1088a.c b/board/freescale/ls1088a/ls1088a.c
index d12bcae..10865fe 100644
--- a/board/freescale/ls1088a/ls1088a.c
+++ b/board/freescale/ls1088a/ls1088a.c
@@ -19,9 +19,13 @@
#include <asm/arch-fsl-layerscape/soc.h>
#include <asm/arch/ppa.h>
#include <hwconfig.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/soc.h>
#include "../common/qixis.h"
#include "ls1088a_qixis.h"
+#include "../common/vid.h"
+#include <fsl_immap.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -51,6 +55,16 @@ unsigned long long get_qixis_addr(void)
}
#endif
+#if defined(CONFIG_VID)
+int init_func_vid(void)
+{
+ if (adjust_vdd(0) < 0)
+ printf("core voltage not adjusted\n");
+
+ return 0;
+}
+#endif
+
#if !defined(CONFIG_SPL_BUILD)
int checkboard(void)
{
@@ -323,6 +337,119 @@ int misc_init_r(void)
}
#endif
+int i2c_multiplexer_select_vid_channel(u8 channel)
+{
+ return select_i2c_ch_pca9547(channel);
+}
+
+#ifdef CONFIG_TARGET_LS1088AQDS
+/* read the current value(SVDD) of the LTM Regulator Voltage */
+int get_serdes_volt(void)
+{
+ int ret, vcode = 0;
+ u8 chan = PWM_CHANNEL0;
+
+ /* Select the PAGE 0 using PMBus commands PAGE for VDD */
+ ret = i2c_write(I2C_SVDD_MONITOR_ADDR,
+ PMBUS_CMD_PAGE, 1, &chan, 1);
+ if (ret) {
+ printf("VID: failed to select VDD Page 0\n");
+ return ret;
+ }
+
+ /* Read the output voltage using PMBus command READ_VOUT */
+ ret = i2c_read(I2C_SVDD_MONITOR_ADDR,
+ PMBUS_CMD_READ_VOUT, 1, (void *)&vcode, 2);
+ if (ret) {
+ printf("VID: failed to read the volatge\n");
+ return ret;
+ }
+
+ return vcode;
+}
+
+int set_serdes_volt(int svdd)
+{
+ int ret, vdd_last;
+ u8 buff[5] = {0x04, PWM_CHANNEL0, PMBUS_CMD_VOUT_COMMAND,
+ svdd & 0xFF, (svdd & 0xFF00) >> 8};
+
+ /* Write the desired voltage code to the SVDD regulator */
+ ret = i2c_write(I2C_SVDD_MONITOR_ADDR,
+ PMBUS_CMD_PAGE_PLUS_WRITE, 1, (void *)&buff, 5);
+ if (ret) {
+ printf("VID: I2C failed to write to the volatge regulator\n");
+ return -1;
+ }
+
+ /* Wait for the volatge to get to the desired value */
+ do {
+ vdd_last = get_serdes_volt();
+ if (vdd_last < 0) {
+ printf("VID: Couldn't read sensor abort VID adjust\n");
+ return -1;
+ }
+ } while (vdd_last != svdd);
+
+ return 1;
+}
+#else
+int get_serdes_volt(void)
+{
+ return 0;
+}
+
+int set_serdes_volt(int svdd)
+{
+ int ret;
+ u8 brdcfg4;
+
+ printf("SVDD changing of RDB\n");
+
+ /* Read the BRDCFG54 via CLPD */
+ ret = i2c_read(CONFIG_SYS_I2C_FPGA_ADDR,
+ QIXIS_BRDCFG4_OFFSET, 1, (void *)&brdcfg4, 1);
+ if (ret) {
+ printf("VID: I2C failed to read the CPLD BRDCFG4\n");
+ return -1;
+ }
+
+ brdcfg4 = brdcfg4 | 0x08;
+
+ /* Write to the BRDCFG4 */
+ ret = i2c_write(CONFIG_SYS_I2C_FPGA_ADDR,
+ QIXIS_BRDCFG4_OFFSET, 1, (void *)&brdcfg4, 1);
+ if (ret) {
+ debug("VID: I2C failed to set the SVDD CPLD BRDCFG4\n");
+ return -1;
+ }
+
+ /* Wait for the volatge to get to the desired value */
+ udelay(10000);
+
+ return 1;
+}
+#endif
+
+/* this function disables the SERDES, changes the SVDD Voltage and enables it*/
+int board_adjust_vdd(int vdd)
+{
+ int ret = 0;
+
+ debug("%s: vdd = %d\n", __func__, vdd);
+
+ /* Special settings to be performed when voltage is 900mV */
+ if (vdd == 900) {
+ ret = setup_serdes_volt(vdd);
+ if (ret < 0) {
+ ret = -1;
+ goto exit;
+ }
+ }
+exit:
+ return ret;
+}
+
int board_init(void)
{
init_final_memctl_regs();
diff --git a/include/configs/ls1088aqds.h b/include/configs/ls1088aqds.h
index cc87997..ca22e7f 100644
--- a/include/configs/ls1088aqds.h
+++ b/include/configs/ls1088aqds.h
@@ -287,6 +287,17 @@ unsigned long get_board_ddr_clk(void);
#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
+#define I2C_SVDD_MONITOR_ADDR 0x4F
+
+#define CONFIG_VID_FLS_ENV "ls1088aqds_vdd_mv"
+#define CONFIG_VID
+
+/* The lowest and highest voltage allowed for LS1088AQDS */
+#define VDD_MV_MIN 819
+#define VDD_MV_MAX 1212
+
+#define CONFIG_VOL_MONITOR_LTC3882_SET
+#define CONFIG_VOL_MONITOR_LTC3882_READ
/* PM Bus commands code for LTC3882*/
#define PMBUS_CMD_PAGE 0x0
diff --git a/include/configs/ls1088ardb.h b/include/configs/ls1088ardb.h
index cbc7d93..af27eb1 100644
--- a/include/configs/ls1088ardb.h
+++ b/include/configs/ls1088ardb.h
@@ -152,6 +152,7 @@
#endif
#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
+#define QIXIS_BRDCFG4_OFFSET 0x54
#define QIXIS_LBMAP_SWITCH 2
#define QIXIS_QMAP_MASK 0xe0
#define QIXIS_QMAP_SHIFT 5
@@ -232,6 +233,17 @@
#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
+#define I2C_SVDD_MONITOR_ADDR 0x4F
+
+#define CONFIG_VID_FLS_ENV "ls1088ardb_vdd_mv"
+#define CONFIG_VID
+
+/* The lowest and highest voltage allowed for LS1088ARDB */
+#define VDD_MV_MIN 819
+#define VDD_MV_MAX 1212
+
+#define CONFIG_VOL_MONITOR_LTC3882_SET
+#define CONFIG_VOL_MONITOR_LTC3882_READ
/* PM Bus commands code for LTC3882*/
#define PMBUS_CMD_PAGE 0x0
--
2.7.4
More information about the U-Boot
mailing list