[U-Boot] [PATCH 4/5] mmc: fsl_esdhc: support SDR104 and HS200

Jaehoon Chung jh80.chung at samsung.com
Fri Jan 19 11:23:46 UTC 2018


On 01/19/2018 06:09 PM, Peng Fan wrote:
> Introduce SDR104 and HS200 support
> The implementation takes linux kernel sdhci.c and sdhci-esdhc-imx.c
> as reference.
>  - Implement esdhc_change_pinstate to dynamically change pad settings
>  - Implement esdhc_set_timing
>  - Implement esdhc_set_voltage to switch voltage
>  - Implement fsl_esdhc_execute_tuning to execute time process
>  - Enlarge the cfg->f_max to 200MHz.
>  - Parse fsl,tuning-step, fsl,tuning-start-tap and
>    fsl,strobe-dll-delay-target from device tree.
>  - Parse no-1-8-v property
>  - Introduce esdhc_soc_data to indicate the flags and caps
> 
> Signed-off-by: Peng Fan <peng.fan at nxp.com>
> Cc: Stefano Babic <sbabic at denx.de>
> Cc: Fabio Estevam <fabio.estevam at nxp.com>
> Cc: Jaehoon Chung <jh80.chung at samsung.com>
> ---
>  drivers/mmc/fsl_esdhc.c | 359 +++++++++++++++++++++++++++++++++++++++++++++++-
>  include/fsl_esdhc.h     |  47 +++++++
>  2 files changed, 401 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c
> index f6279307d8..bd951311cf 100644
> --- a/drivers/mmc/fsl_esdhc.c
> +++ b/drivers/mmc/fsl_esdhc.c
> @@ -23,6 +23,7 @@
>  #include <asm/io.h>
>  #include <dm.h>
>  #include <asm-generic/gpio.h>
> +#include <dm/pinctrl.h>
>  
>  DECLARE_GLOBAL_DATA_PTR;
>  
> @@ -90,6 +91,11 @@ struct fsl_esdhc_plat {
>  	struct mmc mmc;
>  };
>  
> +struct esdhc_soc_data {
> +	u32 flags;
> +	u32 caps;
> +};
> +
>  /**
>   * struct fsl_esdhc_priv
>   *
> @@ -103,12 +109,20 @@ struct fsl_esdhc_plat {
>   * @non_removable: 0: removable; 1: non-removable
>   * @wp_enable: 1: enable checking wp; 0: no check
>   * @vs18_enable: 1: use 1.8V voltage; 0: use 3.3V
> + * @flags: ESDHC_FLAG_xx in include/fsl_esdhc.h
> + * @caps: controller capabilities
> + * @tuning_step: tuning step setting in tuning_ctrl register
> + * @start_tuning_tap: the start point for tuning in tuning_ctrl register
> + * @strobe_dll_delay_target: settings in strobe_dllctrl
> + * @signal_voltage: indicating the current voltage
>   * @cd_gpio: gpio for card detection
>   * @wp_gpio: gpio for write protection
>   */
>  struct fsl_esdhc_priv {
>  	struct fsl_esdhc *esdhc_regs;
>  	unsigned int sdhc_clk;
> +	unsigned int clock;
> +	unsigned int mode;
>  	unsigned int bus_width;
>  #if !CONFIG_IS_ENABLED(BLK)
>  	struct mmc *mmc;
> @@ -117,6 +131,16 @@ struct fsl_esdhc_priv {
>  	int non_removable;
>  	int wp_enable;
>  	int vs18_enable;
> +	u32 flags;
> +	u32 caps;
> +	u32 tuning_step;
> +	u32 tuning_start_tap;
> +	u32 strobe_dll_delay_target;
> +	u32 signal_voltage;
> +#if IS_ENABLED(CONFIG_DM_REGULATOR)
> +	struct udevice *vqmmc_dev;
> +	struct udevice *vmmc_dev;
> +#endif
>  #ifdef CONFIG_DM_GPIO
>  	struct gpio_desc cd_gpio;
>  	struct gpio_desc wp_gpio;
> @@ -364,6 +388,7 @@ static int esdhc_send_cmd_common(struct fsl_esdhc_priv *priv, struct mmc *mmc,
>  	int	err = 0;
>  	uint	xfertyp;
>  	uint	irqstat;
> +	u32	flags;
>  	struct fsl_esdhc *regs = priv->esdhc_regs;
>  
>  #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC111
> @@ -417,8 +442,15 @@ static int esdhc_send_cmd_common(struct fsl_esdhc_priv *priv, struct mmc *mmc,
>  	esdhc_write32(&regs->xfertyp, xfertyp);
>  #endif
>  
> +	if ((cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK) ||
> +	    (cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK_HS200)) {
> +		flags = IRQSTAT_BRR;
> +	} else {
> +		flags = IRQSTAT_CC | IRQSTAT_CTOE;
> +	}

IRQSTAT_CC | IRQSTAT_CTOE can be set to default value like below.

int flags = IRQSTAT_CC | IRQSTAT_CTOE; 

> +
>  	/* Wait for the command to complete */
> -	while (!(esdhc_read32(&regs->irqstat) & (IRQSTAT_CC | IRQSTAT_CTOE)))
> +	while (!(esdhc_read32(&regs->irqstat) & flags))
>  		;
>  
>  	irqstat = esdhc_read32(&regs->irqstat);
> @@ -480,6 +512,12 @@ static int esdhc_send_cmd_common(struct fsl_esdhc_priv *priv, struct mmc *mmc,
>  #ifdef CONFIG_SYS_FSL_ESDHC_USE_PIO
>  		esdhc_pio_read_write(priv, data);
>  #else
> +		flags = DATA_COMPLETE;
> +		if ((cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK) ||
> +		    (cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK_HS200)) {
> +			flags = IRQSTAT_BRR;
> +		}
> +
>  		do {
>  			irqstat = esdhc_read32(&regs->irqstat);
>  
> @@ -492,7 +530,7 @@ static int esdhc_send_cmd_common(struct fsl_esdhc_priv *priv, struct mmc *mmc,
>  				err = -ECOMM;
>  				goto out;
>  			}
> -		} while ((irqstat & DATA_COMPLETE) != DATA_COMPLETE);
> +		} while ((irqstat & flags) != flags);
>  
>  		/*
>  		 * Need invalidate the dcache here again to avoid any
> @@ -573,6 +611,7 @@ static void set_sysctl(struct fsl_esdhc_priv *priv, struct mmc *mmc, uint clock)
>  	esdhc_setbits32(&regs->sysctl, SYSCTL_PEREN | SYSCTL_CKEN);
>  #endif
>  
> +	priv->clock = clock;
>  }
>  
>  #ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK
> @@ -604,9 +643,233 @@ static void esdhc_clock_control(struct fsl_esdhc_priv *priv, bool enable)
>  }
>  #endif
>  
> +#ifdef MMC_SUPPORTS_TUNING
> +static int esdhc_change_pinstate(struct udevice *dev)
> +{
> +	struct fsl_esdhc_priv *priv = dev_get_priv(dev);
> +	int ret;
> +
> +	switch (priv->mode) {
> +	case UHS_SDR50:
> +	case UHS_DDR50:
> +		ret = pinctrl_select_state(dev, "state_100mhz");
> +		break;
> +	case UHS_SDR104:
> +	case MMC_HS_200:
> +		ret = pinctrl_select_state(dev, "state_200mhz");
> +		break;
> +	default:
> +		ret = pinctrl_select_state(dev, "default");
> +		break;
> +	}
> +
> +	if (ret)
> +		printf("%s %d error\n", __func__, priv->mode);
> +
> +	return ret;
> +}
> +
> +static void esdhc_reset_tuning(struct mmc *mmc)
> +{
> +	struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev);
> +	struct fsl_esdhc *regs = priv->esdhc_regs;
> +
> +	if (priv->flags & ESDHC_FLAG_USDHC) {
> +		if (priv->flags & ESDHC_FLAG_STD_TUNING) {

Don't need to use "if" condition at here.
if (priv->flags & (ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING) ?

> +			esdhc_clrbits32(&regs->autoc12err,
> +					MIX_CTRL_SMPCLK_SEL |
> +					MIX_CTRL_EXE_TUNE);
> +		}
> +	}
> +}
> +
> +static int esdhc_set_timing(struct mmc *mmc)
> +{
> +	struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev);
> +	struct fsl_esdhc *regs = priv->esdhc_regs;
> +	u32 m;

Ues the meaningful variable name, not just "m". 

> +
> +	m = readl(&regs->mixctrl);
> +	m &= ~(MIX_CTRL_DDREN | MIX_CTRL_HS400_EN);
> +
> +	switch (mmc->selected_mode) {
> +	case MMC_LEGACY:
> +	case SD_LEGACY:
> +		esdhc_reset_tuning(mmc);
> +		break;
> +	case MMC_HS:
> +	case MMC_HS_52:
> +	case MMC_HS_200:
> +	case SD_HS:
> +	case UHS_SDR12:
> +	case UHS_SDR25:
> +	case UHS_SDR50:
> +	case UHS_SDR104:
> +		writel(m, &regs->mixctrl);
> +		break;
> +	case UHS_DDR50:
> +	case MMC_DDR_52:
> +		m |= MIX_CTRL_DDREN;
> +		writel(m, &regs->mixctrl);
> +		break;
> +	default:
> +		printf("Not supported %d\n", mmc->selected_mode);

Doesn't need to return? Does it need to call esdhc_change_pinstate()?

> +		break;
> +	}
> +
> +	priv->mode = mmc->selected_mode;
> +
> +	return esdhc_change_pinstate(mmc->dev);
> +}
> +
> +static int esdhc_set_voltage(struct mmc *mmc)
> +{
> +	struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev);
> +	struct fsl_esdhc *regs = priv->esdhc_regs;
> +	int ret;
> +
> +	priv->signal_voltage = mmc->signal_voltage;
> +	switch (mmc->signal_voltage) {
> +	case MMC_SIGNAL_VOLTAGE_330:
> +		if (priv->vs18_enable)
> +			return -EIO;
> +		if (!IS_ERR_OR_NULL(priv->vqmmc_dev)) {

Not need to check the CONFIG_DM_REGULATOR for vqmmc_dev and vmmc_dev?

> +			ret = regulator_set_value(priv->vqmmc_dev, 3300000);
> +			if (ret) {
> +				printf("Setting to 3.3V error");
> +				return -EIO;
> +			}
> +			/* Wait for 5ms */
> +			mdelay(5);
> +		}
> +
> +		esdhc_clrbits32(&regs->vendorspec, ESDHC_VENDORSPEC_VSELECT);
> +		if (!(esdhc_read32(&regs->vendorspec) &
> +		    ESDHC_VENDORSPEC_VSELECT))
> +			return 0;
> +
> +		return -EAGAIN;
> +	case MMC_SIGNAL_VOLTAGE_180:
> +		if (!IS_ERR_OR_NULL(priv->vqmmc_dev)) {
> +			ret = regulator_set_value(priv->vqmmc_dev, 1800000);
> +			if (ret) {
> +				printf("Setting to 1.8V error");
> +				return -EIO;
> +			}
> +		}
> +		esdhc_setbits32(&regs->vendorspec, ESDHC_VENDORSPEC_VSELECT);
> +		if (esdhc_read32(&regs->vendorspec) & ESDHC_VENDORSPEC_VSELECT)
> +			return 0;
> +
> +		return -EAGAIN;
> +	case MMC_SIGNAL_VOLTAGE_120:
> +		return -ENOTSUPP;
> +	default:
> +		return 0;
> +	}
> +}
> +
> +static void esdhc_stop_tuning(struct mmc *mmc)
> +{
> +	struct mmc_cmd cmd;
> +
> +	cmd.cmdidx = MMC_CMD_STOP_TRANSMISSION;
> +	cmd.cmdarg = 0;
> +	cmd.resp_type = MMC_RSP_R1b;
> +
> +	dm_mmc_send_cmd(mmc->dev, &cmd, NULL);
> +}
> +
> +static int fsl_esdhc_execute_tuning(struct udevice *dev, uint32_t opcode)
> +{
> +	struct fsl_esdhc_plat *plat = dev_get_platdata(dev);
> +	struct fsl_esdhc_priv *priv = dev_get_priv(dev);
> +	struct fsl_esdhc *regs = priv->esdhc_regs;
> +	struct mmc *mmc = &plat->mmc;
> +	u32 irqstaten = readl(&regs->irqstaten);
> +	u32 irqsigen = readl(&regs->irqsigen);
> +	int i, ret = -ETIMEDOUT;
> +	u32 v, m;

Ditto.

> +
> +	/* clock tuning is not needed for upto 52MHz */
> +	if (mmc->clock <= 52000000)
> +		return 0;
> +
> +	/* This is readw/writew SDHCI_HOST_CONTROL2 when tuning */
> +	if (priv->flags & ESDHC_FLAG_STD_TUNING) {
> +		v = readl(&regs->autoc12err);
> +		m = readl(&regs->mixctrl);
> +		v &= ~MIX_CTRL_SMPCLK_SEL;
> +		m &= ~MIX_CTRL_FBCLK_SEL;
> +		m &= ~MIX_CTRL_AUTO_TUNE_EN;

Combine to one line. 

> +
> +		v |= MIX_CTRL_EXE_TUNE;
> +		m |= MIX_CTRL_FBCLK_SEL;
> +		m |= MIX_CTRL_AUTO_TUNE_EN;

Ditto.

> +
> +		writel(v, &regs->autoc12err);
> +		writel(m, &regs->mixctrl);
> +	}
> +
> +	/* sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE); */
> +	v = readl(&regs->mixctrl);
> +	v = MIX_CTRL_DTDSEL_READ | (v & ~MIX_CTRL_SDHCI_MASK);
> +	writel(v, &regs->mixctrl);
> +
> +	writel(IRQSTATEN_BRR, &regs->irqstaten);
> +	writel(IRQSTATEN_BRR, &regs->irqsigen);
> +
> +	for (i = 0; i < 40; i++) {

What is 40? don't use the magic number.

> +		u32 ctrl;
> +
> +		if (opcode == MMC_CMD_SEND_TUNING_BLOCK_HS200) {
> +			if (mmc->bus_width == 8)
> +				writel(0x7080, &regs->blkattr);
> +			else if (mmc->bus_width == 4)
> +				writel(0x7040, &regs->blkattr);
> +		} else {
> +			writel(0x7040, &regs->blkattr);
> +		}
> +
> +		/* sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE) */
> +		v = readl(&regs->mixctrl);
> +		v = MIX_CTRL_DTDSEL_READ | (v & ~MIX_CTRL_SDHCI_MASK);
> +		writel(v, &regs->mixctrl);
> +
> +		/* We are using STD tuning, no need to check return value */
> +		mmc_send_tuning(mmc, opcode, NULL);

mmc_send_tuning will have the return value, not need to check?

> +
> +		ctrl = readl(&regs->autoc12err);
> +		if ((!(ctrl & MIX_CTRL_EXE_TUNE)) &&
> +		    (ctrl & MIX_CTRL_SMPCLK_SEL)) {
> +			/*
> +			 * need to wait some time, make sure sd/mmc fininsh
> +			 * send out tuning data, otherwise, the sd/mmc can't
> +			 * response to any command when the card still out
> +			 * put the tuning data.
> +			 */
> +			mdelay(1);
> +			ret = 0;
> +			break;
> +		}
> +
> +		/* Add 1ms delay for SD and eMMC */
> +		mdelay(1);
> +	}
> +
> +	writel(irqstaten, &regs->irqstaten);
> +	writel(irqsigen, &regs->irqsigen);
> +
> +	esdhc_stop_tuning(mmc);
> +
> +	return ret;
> +}
> +#endif
> +
>  static int esdhc_set_ios_common(struct fsl_esdhc_priv *priv, struct mmc *mmc)
>  {
>  	struct fsl_esdhc *regs = priv->esdhc_regs;
> +	int ret __maybe_unused;
>  
>  #ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK
>  	/* Select to use peripheral clock */
> @@ -615,7 +878,41 @@ static int esdhc_set_ios_common(struct fsl_esdhc_priv *priv, struct mmc *mmc)
>  	esdhc_clock_control(priv, true);
>  #endif
>  	/* Set the clock speed */
> -	set_sysctl(priv, mmc, mmc->clock);
> +	if (priv->clock != mmc->clock)
> +		set_sysctl(priv, mmc, mmc->clock);
> +
> +#ifdef MMC_SUPPORTS_TUNING
> +	if (mmc->clk_disable) {
> +#ifdef CONFIG_FSL_USDHC
> +		esdhc_clrbits32(&regs->vendorspec, VENDORSPEC_CKEN);
> +#else
> +		esdhc_clrbits32(&regs->sysctl, SYSCTL_CKEN);
> +#endif
> +	} else {
> +#ifdef CONFIG_FSL_USDHC
> +		esdhc_setbits32(&regs->vendorspec, VENDORSPEC_PEREN |
> +				VENDORSPEC_CKEN);
> +#else
> +		esdhc_setbits32(&regs->sysctl, SYSCTL_PEREN | SYSCTL_CKEN);
> +#endif
> +	}
> +
> +	if (priv->mode != mmc->selected_mode) {
> +		ret = esdhc_set_timing(mmc);
> +		if (ret) {
> +			printf("esdhc_set_timing error %d\n", ret);
> +			return ret;
> +		}
> +	}
> +
> +	if (priv->signal_voltage != mmc->signal_voltage) {
> +		ret = esdhc_set_voltage(mmc);
> +		if (ret) {
> +			printf("esdhc_set_voltage error %d\n", ret);
> +			return ret;
> +		}
> +	}
> +#endif
>  
>  	/* Set the bus width */
>  	esdhc_clrbits32(&regs->proctl, PROCTL_DTW_4 | PROCTL_DTW_8);
> @@ -790,6 +1087,10 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv,
>  #ifndef CONFIG_FSL_USDHC
>  	esdhc_setbits32(&regs->sysctl, SYSCTL_PEREN | SYSCTL_HCKEN
>  				| SYSCTL_IPGEN | SYSCTL_CKEN);
> +	/* Clearing tuning bits in case ROM has set it already */
> +	esdhc_write32(&regs->mixctrl, 0);
> +	esdhc_write32(&regs->autoc12err, 0);
> +	esdhc_write32(&regs->clktunectrlstatus, 0);
>  #else
>  	esdhc_setbits32(&regs->vendorspec, VENDORSPEC_PEREN |
>  			VENDORSPEC_HCKEN | VENDORSPEC_IPGEN | VENDORSPEC_CKEN);
> @@ -863,11 +1164,27 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv,
>  		cfg->host_caps &= ~MMC_MODE_8BIT;
>  #endif
>  
> +	cfg->host_caps |= priv->caps;
> +
>  	cfg->f_min = 400000;
> -	cfg->f_max = min(priv->sdhc_clk, (u32)52000000);
> +	cfg->f_max = min(priv->sdhc_clk, (u32)200000000);
>  
>  	cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT;
>  
> +	writel(0, &regs->dllctrl);
> +	if (priv->flags & ESDHC_FLAG_USDHC) {
> +		if (priv->flags & ESDHC_FLAG_STD_TUNING) {

Ditto.

> +			u32 val = readl(&regs->tuning_ctrl);
> +
> +			val |= ESDHC_STD_TUNING_EN;
> +			val &= ~ESDHC_TUNING_START_TAP_MASK;
> +			val |= priv->tuning_start_tap;
> +			val &= ~ESDHC_TUNING_STEP_MASK;
> +			val |= (priv->tuning_step) << ESDHC_TUNING_STEP_SHIFT;
> +			writel(val, &regs->tuning_ctrl);
> +		}
> +	}
> +
>  	return 0;
>  }
>  
> @@ -1026,6 +1343,10 @@ static int fsl_esdhc_probe(struct udevice *dev)
>  	struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
>  	struct fsl_esdhc_plat *plat = dev_get_platdata(dev);
>  	struct fsl_esdhc_priv *priv = dev_get_priv(dev);
> +	const void *fdt = gd->fdt_blob;
> +	int node = dev_of_offset(dev);
> +	struct esdhc_soc_data *data =
> +		(struct esdhc_soc_data *)dev_get_driver_data(dev);
>  #ifdef CONFIG_DM_REGULATOR
>  	struct udevice *vqmmc_dev;
>  #endif
> @@ -1040,6 +1361,11 @@ static int fsl_esdhc_probe(struct udevice *dev)
>  
>  	priv->esdhc_regs = (struct fsl_esdhc *)addr;
>  	priv->dev = dev;
> +	priv->mode = -1;
> +	if (data) {
> +		priv->flags = data->flags;
> +		priv->caps = data->caps;
> +	}
>  
>  	val = dev_read_u32_default(dev, "bus-width", -1);
>  	if (val == 8)
> @@ -1049,6 +1375,15 @@ static int fsl_esdhc_probe(struct udevice *dev)
>  	else
>  		priv->bus_width = 1;
>  
> +	val = fdtdec_get_int(fdt, node, "fsl,tuning-step", 1);
> +	priv->tuning_step = val;
> +	val = fdtdec_get_int(fdt, node, "fsl,tuning-start-tap",
> +			     ESDHC_TUNING_START_TAP_DEFAULT);
> +	priv->tuning_start_tap = val;
> +	val = fdtdec_get_int(fdt, node, "fsl,strobe-dll-delay-target",
> +			     ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT);
> +	priv->strobe_dll_delay_target = val;
> +
>  	if (dev_read_bool(dev, "non-removable")) {
>  		priv->non_removable = 1;
>  	 } else {
> @@ -1090,6 +1425,9 @@ static int fsl_esdhc_probe(struct udevice *dev)
>  	}
>  #endif
>  
> +	if (fdt_get_property(fdt, node, "no-1-8-v", NULL))
> +		priv->caps &= ~(UHS_CAPS | MMC_MODE_HS200);
> +
>  	/*
>  	 * TODO:
>  	 * Because lack of clk driver, if SDHC clk is not enabled,
> @@ -1162,15 +1500,26 @@ static const struct dm_mmc_ops fsl_esdhc_ops = {
>  	.get_cd		= fsl_esdhc_get_cd,
>  	.send_cmd	= fsl_esdhc_send_cmd,
>  	.set_ios	= fsl_esdhc_set_ios,
> +#ifdef MMC_SUPPORTS_TUNING
> +	.execute_tuning	= fsl_esdhc_execute_tuning,
> +#endif
>  };
>  #endif
>  
> +static struct esdhc_soc_data usdhc_imx7d_data = {
> +	.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
> +			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
> +			| ESDHC_FLAG_HS400,
> +	.caps = UHS_CAPS | MMC_MODE_HS200 | MMC_MODE_DDR_52MHz |
> +		MMC_MODE_HS_52MHz | MMC_MODE_HS,
> +};
> +
>  static const struct udevice_id fsl_esdhc_ids[] = {
>  	{ .compatible = "fsl,imx6ul-usdhc", },
>  	{ .compatible = "fsl,imx6sx-usdhc", },
>  	{ .compatible = "fsl,imx6sl-usdhc", },
>  	{ .compatible = "fsl,imx6q-usdhc", },
> -	{ .compatible = "fsl,imx7d-usdhc", },
> +	{ .compatible = "fsl,imx7d-usdhc", .data = (ulong)&usdhc_imx7d_data,},
>  	{ .compatible = "fsl,imx7ulp-usdhc", },
>  	{ .compatible = "fsl,esdhc", },
>  	{ /* sentinel */ }
> diff --git a/include/fsl_esdhc.h b/include/fsl_esdhc.h
> index de1f5e7d9f..b341e018f2 100644
> --- a/include/fsl_esdhc.h
> +++ b/include/fsl_esdhc.h
> @@ -10,6 +10,7 @@
>  #ifndef  __FSL_ESDHC_H__
>  #define	__FSL_ESDHC_H__
>  
> +#include <linux/bitops.h>
>  #include <linux/errno.h>
>  #include <asm/byteorder.h>
>  
> @@ -173,6 +174,52 @@
>  
>  #define ESDHC_VENDORSPEC_VSELECT 0x00000002 /* Use 1.8V */
>  
> +/* Imported from Linux Kernel drivers/mmc/host/sdhci-esdhc-imx.c */
> +#define	MIX_CTRL_DDREN		BIT(3)
> +#define MIX_CTRL_DTDSEL_READ	BIT(4)
> +#define	MIX_CTRL_AC23EN		BIT(7)
> +#define	MIX_CTRL_EXE_TUNE	BIT(22)
> +#define	MIX_CTRL_SMPCLK_SEL	BIT(23)
> +#define	MIX_CTRL_AUTO_TUNE_EN	BIT(24)
> +#define	MIX_CTRL_FBCLK_SEL	BIT(25)
> +#define	MIX_CTRL_HS400_EN	BIT(26)
> +#define	MIX_CTRL_HS400_ES	BIT(27)
> +/* Bits 3 and 6 are not SDHCI standard definitions */
> +#define	MIX_CTRL_SDHCI_MASK	0xb7
> +/* Tuning bits */
> +#define	MIX_CTRL_TUNING_MASK	0x03c00000
> +
> +/* strobe dll register */
> +#define ESDHC_STROBE_DLL_CTRL		0x70
> +#define ESDHC_STROBE_DLL_CTRL_ENABLE	BIT(0)
> +#define ESDHC_STROBE_DLL_CTRL_RESET	BIT(1)
> +#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT	0x7
> +#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT	3
> +
> +#define ESDHC_STROBE_DLL_STATUS		0x74
> +#define ESDHC_STROBE_DLL_STS_REF_LOCK	BIT(1)
> +#define ESDHC_STROBE_DLL_STS_SLV_LOCK	0x1
> +#define ESDHC_STROBE_DLL_CLK_FREQ	100000000
> +
> +#define ESDHC_STD_TUNING_EN             BIT(24)
> +/* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
> +#define ESDHC_TUNING_START_TAP_DEFAULT	0x1
> +#define ESDHC_TUNING_START_TAP_MASK	0xff
> +#define ESDHC_TUNING_STEP_MASK		0x00070000
> +#define ESDHC_TUNING_STEP_SHIFT		16
> +
> +#define	ESDHC_FLAG_MULTIBLK_NO_INT	BIT(1)
> +#define	ESDHC_FLAG_ENGCM07207		BIT(2)
> +#define	ESDHC_FLAG_USDHC		BIT(3)
> +#define	ESDHC_FLAG_MAN_TUNING		BIT(4)
> +#define	ESDHC_FLAG_STD_TUNING		BIT(5)
> +#define	ESDHC_FLAG_HAVE_CAP1		BIT(6)
> +#define	ESDHC_FLAG_ERR004536		BIT(7)
> +#define	ESDHC_FLAG_HS200		BIT(8)
> +#define	ESDHC_FLAG_HS400		BIT(9)
> +#define	ESDHC_FLAG_ERR010450		BIT(10)
> +#define	ESDHC_FLAG_HS400_ES		BIT(11)
> +
>  struct fsl_esdhc_cfg {
>  	phys_addr_t esdhc_base;
>  	u32	sdhc_clk;
> 



More information about the U-Boot mailing list