[U-Boot] [PATCH v3 0/9] Add new OPTEE bootm support to u-boot

[Bryan O'Donoghue]

v3:

- Rework printout to be added at the end as opposed to churn over three
  separate patches - Andrew

- Reword patch 006 to better explain the thinking behind new image type
  - Andrew

v2:
- Added CONFIG_OPTEE_TZDRAM_BASE instead of #ifndef OPTEE_TZDRAM_BASE
  as an error. - Tom Rini

- Added Tested-by: Peng Fan <peng.fan at nxp.com> - as indicated

- Added better explanation text to patch 6/9
  "tools: mkimage: add optee image type"

- Fixed some checkpatch warnings in optee.c

v1:
This series adds a new OPTEE bootable image type to u-boot, which is
directly bootable with the bootm command.

There is already a TEE image type but, in this case the TEE firmware is
loaded into RAM, jumped into and then back out of. This image type is a
directly bootable image as described here :
http://mrvan.github.io/optee-imx6ul

Instead of reusing the Linux bootable image type instead a new image type
is defined, which allows us to perform additional image verification, prior
to handing off control via bootm.

OPTEE images get linked to a specific address at compile time and must be
loaded to this address too. This series extends out mkimage with a new
image type that allows the OPTEE binary link location to be validated
against CONFIG_OPTEE_TZDRAM_BASE and CONFIG_OPTEE_TZDRAM_SIZE respectively
prior to proceeding through the bootm phase.

Once applied you can generate a bootable OPTEE image like this

mkimage -A arm -T optee -C none -d ./out/arm-plat-imx/core/tee.bin uTee.optee

That image can then be booted directly by bootm. bootm will verify the
header contents of the OPTEE binary against the DRAM area carved out in
u-boot. If the defined DRAM area does not match the link address specified
we refuse to boot.

Kever - I'd like to suggest that your OPTEE SPL image takes a different
image type IH_TYPE_OPTEE_SPL ? to indicate the different behavior your
image type has versus a directly bootable bootm image.

Bryan O'Donoghue (9):
  optee: Add lib entries for sharing OPTEE code across ports
  optee: Add CONFIG_OPTEE_TZDRAM_SIZE
  optee: Add CONFIG_OPTEE_TZDRAM_BASE
  optee: Add optee_image_get_entry_point()
  optee: Add optee_image_get_load_addr()
  tools: mkimage: add optee image type
  optee: Add optee_verify_bootm_image()
  optee: Add error printout
  bootm: optee: Add mechanism to validate an OPTEE image before boot

 common/bootm.c        | 11 ++++++++-
 common/image.c        |  1 +
 include/image.h       |  1 +
 include/tee/optee.h   | 41 ++++++++++++++++++++++++++++++++
 lib/Kconfig           |  1 +
 lib/Makefile          |  1 +
 lib/optee/Kconfig     | 24 +++++++++++++++++++
 lib/optee/Makefile    |  7 ++++++
 lib/optee/optee.c     | 66 +++++++++++++++++++++++++++++++++++++++++++++++++++
 tools/default_image.c | 25 ++++++++++++++-----
 10 files changed, 171 insertions(+), 7 deletions(-)
 create mode 100644 lib/optee/Kconfig
 create mode 100644 lib/optee/Makefile
 create mode 100644 lib/optee/optee.c

-- 
2.7.4