[U-Boot] [PATCH v2 00/24] omap_hsmmc: Add support for HS200 and UHS modes

[Lokesh Vutla]

On Thursday 25 January 2018 04:21 PM, Jean-Jacques Hiblot wrote:
> 
> This series adds the missing bits to enable the UHS and HS200 modes
> for the TI platforms.

For my understanding, these patches enable HS modes only in U-Boot
proper or in SPL also?

Thanks and regards,
Lokesh

> 
> Enabling support for high speed modes on omap5 requires implementing:
>  * io signal voltage selection
>  * tuning support
>  * pin configuration (IO delays)
> 
> The few last patches enable the high speed modes for the DRA7 platforms and
> also take care of disabling those modes in the dts for the platforms that
> cannot support either the UHS or the HS200 because the voltage regulators
> on board would not allow using those modes (not a SOC limitation).
> 
> With this in place we observe significant improvements in the performances:
> on a DRA72 evm:
> eMMC HS200: 124 MB/s
> eMMC DDR52: 78 MB/s
> sd   SDR104: 71 MB/s
> sd   SDR50: 44 MB/s
> For the record, the original performances were:
> SD High speed: 18 MB/s
> MMC High speed: 18 MB/s
> 
> This series has been tested on:
> * DRA71-evm
> * DRA72-evm
> * DRA7x-evm
> * DRA76-evm
> * AM57x-evm
> * Beaglebone Black (dt and non-dt)
> 
> changes since v1:
>  - rebased on top of u-boot/master
>  - enable the H200 and UHS support in the defconfigs of the DRA7 platforms
> 
> 
> 
> Jean-Jacques Hiblot (9):
>   mmc: omap_hsmmc: Reduce the max timeout for reset controller fsm
>   mmc: omap_hsmmc: allow the simple HS modes to use the default pinctrl
>   mmc: omap_hsmmc: update mmc->clock with the actual bus speed
>   mmc: omap_hsmmc: implement send_init_stream callback
>   mmc: omap_hsmmc: add signal voltage selection support
>   ARM: dts: dra7: Add supported MMC/SD modes in MMC dt nodes
>   dts: am57xx-beagle-x15: disable UHS and HS200 support
>   dts: am57xx-idk: disable HS200 support
>   configs: dra7xx_evm/dra7xx_hs_evm: Enable MMC HS200 and SD UHS support
> 
> Kishon Vijay Abraham I (15):
>   mmc: omap_hsmmc: cleanup clock configuration
>   mmc: omap_hsmmc: cleanup omap_hsmmc_set_ios
>   mmc: omap_hsmmc: add support to set default io voltage
>   mmc: omap_hsmmc: set MMC mode in the UHSMS bit field
>   mmc: omap_hsmmc: Enable DDR mode support
>   mmc: omap_hsmmc: Add tuning support
>   mmc: omap_hsmmc: Workaround for errata id i802
>   mmc: omap_hsmmc: use mmc_of_parse to populate mmc_config
>   ARM: OMAP5/DRA7: Enable iodelay recalibration to be done from uboot
>   mmc: omap_hsmmc: Add support to set IODELAY values
>   mmc: omap_hsmmc: Add support to get pinctrl values and max frequency
>     for different hw revisions
>   mmc: omap_hsmmc: allow mmc clock to be gated
>   ARM: OMAP5: set mmc clock frequency to 192MHz
>   ARM: dts: DRA7: use new dra7-specific compatible string
>   ARM: DRA7x/AM57x: Add MMC/SD fixups for rev1.0 and rev 1.1
> 
>  arch/arm/dts/am57xx-beagle-x15.dts               |   6 +
>  arch/arm/dts/am57xx-idk-common.dtsi              |   2 +
>  arch/arm/dts/dra7.dtsi                           |  22 +-
>  arch/arm/include/asm/arch-omap5/clock.h          |   2 +-
>  arch/arm/include/asm/arch-omap5/dra7xx_iodelay.h |   3 +
>  arch/arm/include/asm/arch-omap5/sys_proto.h      |   7 +
>  arch/arm/include/asm/omap_mmc.h                  |  59 +-
>  arch/arm/mach-omap2/omap5/dra7xx_iodelay.c       |  30 +
>  arch/arm/mach-omap2/omap5/hw_data.c              |  10 +-
>  board/ti/am57xx/board.c                          |  30 +
>  board/ti/dra7xx/evm.c                            |  29 +
>  configs/dra7xx_evm_defconfig                     |   3 +
>  configs/dra7xx_hs_evm_defconfig                  |   3 +
>  drivers/mmc/omap_hsmmc.c                         | 948 +++++++++++++++++++++--
>  include/configs/am57xx_evm.h                     |   2 -
>  include/configs/dra7xx_evm.h                     |   2 -
>  16 files changed, 1085 insertions(+), 73 deletions(-)
>