[U-Boot] [PATCH v3 09/13] board: freescale: ls1012a2g5rdb: enable network support on ls1012a2g5rdb

[Calvin Johnson]

This patch enables ethernet support for ls1012a2g5rdb.

Signed-off-by: Calvin Johnson <calvin.johnson at nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya at nxp.com>

---

Changes in v3:
-Update Kconfig
-Update header file location to include/net/pfe_eth
-Prefix CONFIG_PFE_ to appropriate macros
-Indent properly

Changes in v2:
-New patch added to series to enable ethernet support for
ls1012a2g5rdb

 board/freescale/ls1012ardb/Kconfig | 30 +++++++++++++++++++++++++
 board/freescale/ls1012ardb/eth.c   | 45 +++++++++++++++++++++++++++++++-------
 2 files changed, 67 insertions(+), 8 deletions(-)

diff --git a/board/freescale/ls1012ardb/Kconfig b/board/freescale/ls1012ardb/Kconfig
index af35a01..493d477 100644
--- a/board/freescale/ls1012ardb/Kconfig
+++ b/board/freescale/ls1012ardb/Kconfig
@@ -59,6 +59,36 @@ config SYS_SOC
 config SYS_CONFIG_NAME
         default "ls1012a2g5rdb"
 
+if FSL_PFE
+
+config BOARD_SPECIFIC_OPTIONS # dummy
+	def_bool y
+	select PHYLIB
+	imply CONFIG_PHYLIB_10G
+	imply CONFIG_PHY_AQUANTIA
+
+config SYS_LS_PFE_FW_ADDR
+	hex "Flash address of PFE firmware"
+	default 0x40a00000
+
+config DDR_PFE_PHYS_BASEADDR
+	hex "PFE DDR physical base address"
+	default 0x03800000
+
+config DDR_PFE_BASEADDR
+	hex "PFE DDR base address"
+	default 0x83800000
+
+config PFE_EMAC1_PHY_ADDR
+	hex "PFE DDR base address"
+	default 0x2
+
+config PFE_EMAC2_PHY_ADDR
+	hex "PFE DDR base address"
+	default 0x1
+
+endif
+
 source "board/freescale/common/Kconfig"
 
 endif
diff --git a/board/freescale/ls1012ardb/eth.c b/board/freescale/ls1012ardb/eth.c
index e6379a3..8e6cd0a 100644
--- a/board/freescale/ls1012ardb/eth.c
+++ b/board/freescale/ls1012ardb/eth.c
@@ -26,6 +26,7 @@
 
 static inline void ls1012ardb_reset_phy(void)
 {
+#ifdef CONFIG_TARGET_LS1012ARDB
 	/* Through reset IO expander reset both RGMII and SGMII PHYs */
 	i2c_reg_write(I2C_MUX_IO2_ADDR, 6, __PHY_MASK);
 	i2c_reg_write(I2C_MUX_IO2_ADDR, 2, __PHY_ETH2_MASK);
@@ -34,6 +35,7 @@ static inline void ls1012ardb_reset_phy(void)
 	mdelay(10);
 	i2c_reg_write(I2C_MUX_IO2_ADDR, 2, 0xFF);
 	mdelay(50);
+#endif
 }
 
 int pfe_eth_board_init(struct udevice *dev)
@@ -42,6 +44,11 @@ int pfe_eth_board_init(struct udevice *dev)
 	struct mii_dev *bus;
 	struct pfe_mdio_info mac_mdio_info;
 	struct pfe_eth_dev *priv = dev_get_priv(dev);
+	struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+
+	int srds_s1 = in_be32(&gur->rcwsr[4]) &
+			FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;
+	srds_s1 >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT;
 
 	if (!init_done) {
 		ls1012ardb_reset_phy();
@@ -59,14 +66,36 @@ int pfe_eth_board_init(struct udevice *dev)
 	pfe_set_mdio(priv->gemac_port,
 		     miiphy_get_dev_by_name(DEFAULT_PFE_MDIO_NAME));
 
-	if (!priv->gemac_port) {
-		/* MAC1 */
-		pfe_set_phy_address_mode(priv->gemac_port, EMAC1_PHY_ADDR,
-					 PHY_INTERFACE_MODE_SGMII);
-	} else {
-		/* MAC2 */
-		pfe_set_phy_address_mode(priv->gemac_port, EMAC2_PHY_ADDR,
-					 PHY_INTERFACE_MODE_RGMII_TXID);
+	switch (srds_s1) {
+	case 0x3508:
+		if (!priv->gemac_port) {
+			/* MAC1 */
+			pfe_set_phy_address_mode(priv->gemac_port,
+						 CONFIG_PFE_EMAC1_PHY_ADDR,
+						 PHY_INTERFACE_MODE_SGMII);
+		} else {
+			/* MAC2 */
+			pfe_set_phy_address_mode(priv->gemac_port,
+						 CONFIG_PFE_EMAC2_PHY_ADDR,
+						 PHY_INTERFACE_MODE_RGMII_TXID);
+		}
+		break;
+	case 0x2208:
+		if (!priv->gemac_port) {
+			/* MAC1 */
+			pfe_set_phy_address_mode(priv->gemac_port,
+						 CONFIG_PFE_EMAC1_PHY_ADDR,
+						 PHY_INTERFACE_MODE_SGMII_2500);
+		} else {
+			/* MAC2 */
+			pfe_set_phy_address_mode(priv->gemac_port,
+						 CONFIG_PFE_EMAC2_PHY_ADDR,
+						 PHY_INTERFACE_MODE_SGMII_2500);
+		}
+		break;
+	default:
+		printf("unsupported SerDes PRCTL= %d\n", srds_s1);
+		break;
 	}
 	return 0;
 }
-- 
2.7.4