[U-Boot] [PATCH v3 3/6] ARM: mvebu: a38x: remove some unused code
Chris Packham
judge.packham at gmail.com
Thu May 10 01:28:28 UTC 2018
No in-tree code defines SUPPORT_STATIC_DUNIT_CONFIG or
STATIC_ALGO_SUPPORT. Remove ddr3_a38x_mc_static.h and use unifdef to
remove unused sections in the rest of the ddr/marvell/a38x code.
Signed-off-by: Chris Packham <judge.packham at gmail.com>
---
Much of this code is moved/removed in the updated DDR code so this
commit helps minimise the final delta.
Changes in v3: None
Changes in v2: None
drivers/ddr/marvell/a38x/ddr3_a38x.c | 51 --
.../ddr/marvell/a38x/ddr3_a38x_mc_static.h | 225 ---------
drivers/ddr/marvell/a38x/ddr3_debug.c | 9 -
drivers/ddr/marvell/a38x/ddr3_init.c | 29 --
drivers/ddr/marvell/a38x/ddr3_init.h | 1 -
drivers/ddr/marvell/a38x/ddr3_training.c | 41 --
.../ddr/marvell/a38x/ddr3_training_static.c | 438 ------------------
7 files changed, 794 deletions(-)
delete mode 100644 drivers/ddr/marvell/a38x/ddr3_a38x_mc_static.h
diff --git a/drivers/ddr/marvell/a38x/ddr3_a38x.c b/drivers/ddr/marvell/a38x/ddr3_a38x.c
index e152e842aef1..c356d0900870 100644
--- a/drivers/ddr/marvell/a38x/ddr3_a38x.c
+++ b/drivers/ddr/marvell/a38x/ddr3_a38x.c
@@ -76,41 +76,6 @@ struct trip_delay_element a38x_board_round_trip_delay_array[] = {
{ 4282, 6160 } /* ECC PUP */
};
-#ifdef STATIC_ALGO_SUPPORT
-/* package trace */
-static struct trip_delay_element a38x_package_round_trip_delay_array[] = {
- /* IF BUS DQ_DELAY CK_DELAY */
- { 0, 0 },
- { 0, 0 },
- { 0, 0 },
- { 0, 0 },
- { 0, 0 },
- { 0, 0 },
- { 0, 0 },
- { 0, 0 },
- { 0, 0 },
- { 0, 0 },
- { 0, 0 },
- { 0, 0 },
- { 0, 0 },
- { 0, 0 },
- { 0, 0 },
- { 0, 0 },
- { 0, 0 },
- { 0, 0 },
- { 0, 0 },
- { 0, 0 }
-};
-
-static int a38x_silicon_delay_offset[] = {
- /* board 0 */
- 0,
- /* board 1 */
- 0,
- /* board 2 */
- 0
-};
-#endif
static u8 a38x_bw_per_freq[DDR_FREQ_LIMIT] = {
0x3, /* DDR_FREQ_100 */
@@ -367,22 +332,6 @@ static int ddr3_tip_init_a38x_silicon(u32 dev_num, u32 board_id)
ddr3_tip_register_dq_table(dev_num, dq_bit_map_2_phy_pin);
-#ifdef STATIC_ALGO_SUPPORT
- {
- struct hws_tip_static_config_info static_config;
- u32 board_offset =
- board_id * A38X_NUMBER_OF_INTERFACES *
- tm->num_of_bus_per_interface;
-
- static_config.silicon_delay =
- a38x_silicon_delay_offset[board_id];
- static_config.package_trace_arr =
- a38x_package_round_trip_delay_array;
- static_config.board_trace_arr =
- &a38x_board_round_trip_delay_array[board_offset];
- ddr3_tip_init_static_config_db(dev_num, &static_config);
- }
-#endif
status = ddr3_tip_a38x_get_init_freq(dev_num, &ddr_freq);
if (MV_OK != status) {
DEBUG_TRAINING_ACCESS(DEBUG_LEVEL_ERROR,
diff --git a/drivers/ddr/marvell/a38x/ddr3_a38x_mc_static.h b/drivers/ddr/marvell/a38x/ddr3_a38x_mc_static.h
deleted file mode 100644
index a5b4f7045895..000000000000
--- a/drivers/ddr/marvell/a38x/ddr3_a38x_mc_static.h
+++ /dev/null
@@ -1,225 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (C) Marvell International Ltd. and its affiliates
- */
-
-#ifndef _DDR3_A38X_MC_STATIC_H
-#define _DDR3_A38X_MC_STATIC_H
-
-#include "ddr3_a38x.h"
-
-#ifdef SUPPORT_STATIC_DUNIT_CONFIG
-
-#ifdef CONFIG_CUSTOMER_BOARD_SUPPORT
-static struct reg_data ddr3_customer_800[] = {
- /* parameters for customer board (based on 800MHZ) */
- {0x1400, 0x7b00cc30, 0xffffffff},
- {0x1404, 0x36301820, 0xffffffff},
- {0x1408, 0x5415baab, 0xffffffff},
- {0x140c, 0x38411def, 0xffffffff},
- {0x1410, 0x18300000, 0xffffffff},
- {0x1414, 0x00000700, 0xffffffff},
- {0x1424, 0x0060f3ff, 0xffffffff},
- {0x1428, 0x0011a940, 0xffffffff},
- {0x142c, 0x28c5134, 0xffffffff},
- {0x1474, 0x00000000, 0xffffffff},
- {0x147c, 0x0000d771, 0xffffffff},
- {0x1494, 0x00030000, 0xffffffff},
- {0x149c, 0x00000300, 0xffffffff},
- {0x14a8, 0x00000000, 0xffffffff},
- {0x14cc, 0xbd09000d, 0xffffffff},
- {0x1504, 0xfffffff1, 0xffffffff},
- {0x150c, 0xffffffe5, 0xffffffff},
- {0x1514, 0x00000000, 0xffffffff},
- {0x151c, 0x00000000, 0xffffffff},
- {0x1538, 0x00000b0b, 0xffffffff},
- {0x153c, 0x00000c0c, 0xffffffff},
- {0x15d0, 0x00000670, 0xffffffff},
- {0x15d4, 0x00000046, 0xffffffff},
- {0x15d8, 0x00000010, 0xffffffff},
- {0x15dc, 0x00000000, 0xffffffff},
- {0x15e0, 0x00000023, 0xffffffff},
- {0x15e4, 0x00203c18, 0xffffffff},
- {0x15ec, 0xf8000019, 0xffffffff},
- {0x16a0, 0xcc000006, 0xffffffff}, /* Clock Delay */
- {0xe4124, 0x08008073, 0xffffffff}, /* AVS BG default */
- {0, 0, 0}
-};
-
-#else /* CONFIG_CUSTOMER_BOARD_SUPPORT */
-
-struct reg_data ddr3_a38x_933[MV_MAX_DDR3_STATIC_SIZE] = {
- /* parameters for 933MHZ */
- {0x1400, 0x7b00ce3a, 0xffffffff},
- {0x1404, 0x36301820, 0xffffffff},
- {0x1408, 0x7417eccf, 0xffffffff},
- {0x140c, 0x3e421f98, 0xffffffff},
- {0x1410, 0x1a300000, 0xffffffff},
- {0x1414, 0x00000700, 0xffffffff},
- {0x1424, 0x0060f3ff, 0xffffffff},
- {0x1428, 0x0013ca50, 0xffffffff},
- {0x142c, 0x028c5165, 0xffffffff},
- {0x1474, 0x00000000, 0xffffffff},
- {0x147c, 0x0000e871, 0xffffffff},
- {0x1494, 0x00010000, 0xffffffff},
- {0x149c, 0x00000001, 0xffffffff},
- {0x14a8, 0x00000000, 0xffffffff},
- {0x14cc, 0xbd09000d, 0xffffffff},
- {0x1504, 0xffffffe1, 0xffffffff},
- {0x150c, 0xffffffe5, 0xffffffff},
- {0x1514, 0x00000000, 0xffffffff},
- {0x151c, 0x00000000, 0xffffffff},
- {0x1538, 0x00000d0d, 0xffffffff},
- {0x153c, 0x00000d0d, 0xffffffff},
- {0x15d0, 0x00000608, 0xffffffff},
- {0x15d4, 0x00000044, 0xffffffff},
- {0x15d8, 0x00000020, 0xffffffff},
- {0x15dc, 0x00000000, 0xffffffff},
- {0x15e0, 0x00000021, 0xffffffff},
- {0x15e4, 0x00203c18, 0xffffffff},
- {0x15ec, 0xf8000019, 0xffffffff},
- {0x16a0, 0xcc000006, 0xffffffff}, /* Clock Delay */
- {0xe4124, 0x08008073, 0xffffffff}, /* AVS BG default */
- {0, 0, 0}
-};
-
-static struct reg_data ddr3_a38x_800[] = {
- /* parameters for 800MHZ */
- {0x1400, 0x7b00cc30, 0xffffffff},
- {0x1404, 0x36301820, 0xffffffff},
- {0x1408, 0x5415baab, 0xffffffff},
- {0x140c, 0x38411def, 0xffffffff},
- {0x1410, 0x18300000, 0xffffffff},
- {0x1414, 0x00000700, 0xffffffff},
- {0x1424, 0x0060f3ff, 0xffffffff},
- {0x1428, 0x0011a940, 0xffffffff},
- {0x142c, 0x28c5134, 0xffffffff},
- {0x1474, 0x00000000, 0xffffffff},
- {0x147c, 0x0000d771, 0xffffffff},
- {0x1494, 0x00030000, 0xffffffff},
- {0x149c, 0x00000300, 0xffffffff},
- {0x14a8, 0x00000000, 0xffffffff},
- {0x14cc, 0xbd09000d, 0xffffffff},
- {0x1504, 0xfffffff1, 0xffffffff},
- {0x150c, 0xffffffe5, 0xffffffff},
- {0x1514, 0x00000000, 0xffffffff},
- {0x151c, 0x00000000, 0xffffffff},
- {0x1538, 0x00000b0b, 0xffffffff},
- {0x153c, 0x00000c0c, 0xffffffff},
- {0x15d0, 0x00000670, 0xffffffff},
- {0x15d4, 0x00000046, 0xffffffff},
- {0x15d8, 0x00000010, 0xffffffff},
- {0x15dc, 0x00000000, 0xffffffff},
- {0x15e0, 0x00000023, 0xffffffff},
- {0x15e4, 0x00203c18, 0xffffffff},
- {0x15ec, 0xf8000019, 0xffffffff},
- {0x16a0, 0xcc000006, 0xffffffff}, /* Clock Delay */
- {0xe4124, 0x08008073, 0xffffffff}, /* AVS BG default */
- {0, 0, 0}
-};
-
-static struct reg_data ddr3_a38x_667[] = {
- /* parameters for 667MHZ */
- /* DDR SDRAM Configuration Register */
- {0x1400, 0x7b00ca28, 0xffffffff},
- /* Dunit Control Low Register - kw28 bit12 low (disable CLK1) */
- {0x1404, 0x36301820, 0xffffffff},
- /* DDR SDRAM Timing (Low) Register */
- {0x1408, 0x43149997, 0xffffffff},
- /* DDR SDRAM Timing (High) Register */
- {0x140c, 0x38411bc7, 0xffffffff},
- /* DDR SDRAM Address Control Register */
- {0x1410, 0x14330000, 0xffffffff},
- /* DDR SDRAM Open Pages Control Register */
- {0x1414, 0x00000700, 0xffffffff},
- /* Dunit Control High Register (2 :1 - bits 15:12 = 0xd) */
- {0x1424, 0x0060f3ff, 0xffffffff},
- /* Dunit Control High Register */
- {0x1428, 0x000f8830, 0xffffffff},
- /* Dunit Control High Register (2:1 - bit 29 = '1') */
- {0x142c, 0x28c50f8, 0xffffffff},
- {0x147c, 0x0000c671, 0xffffffff},
- /* DDR SDRAM ODT Control (Low) Register */
- {0x1494, 0x00030000, 0xffffffff},
- /* DDR SDRAM ODT Control (High) Register, will be configured at WL */
- {0x1498, 0x00000000, 0xffffffff},
- /* DDR Dunit ODT Control Register */
- {0x149c, 0x00000300, 0xffffffff},
- {0x14a8, 0x00000000, 0xffffffff}, /* */
- {0x14cc, 0xbd09000d, 0xffffffff}, /* */
- {0x1474, 0x00000000, 0xffffffff},
- /* Read Data Sample Delays Register */
- {0x1538, 0x00000009, 0xffffffff},
- /* Read Data Ready Delay Register */
- {0x153c, 0x0000000c, 0xffffffff},
- {0x1504, 0xfffffff1, 0xffffffff}, /* */
- {0x150c, 0xffffffe5, 0xffffffff}, /* */
- {0x1514, 0x00000000, 0xffffffff}, /* */
- {0x151c, 0x0, 0xffffffff}, /* */
- {0x15d0, 0x00000650, 0xffffffff}, /* MR0 */
- {0x15d4, 0x00000046, 0xffffffff}, /* MR1 */
- {0x15d8, 0x00000010, 0xffffffff}, /* MR2 */
- {0x15dc, 0x00000000, 0xffffffff}, /* MR3 */
- {0x15e0, 0x23, 0xffffffff}, /* */
- {0x15e4, 0x00203c18, 0xffffffff}, /* ZQC Configuration Register */
- {0x15ec, 0xf8000019, 0xffffffff}, /* DDR PHY */
- {0x16a0, 0xcc000006, 0xffffffff}, /* Clock Delay */
- {0xe4124, 0x08008073, 0xffffffff}, /* AVS BG default */
- {0, 0, 0}
-};
-
-static struct reg_data ddr3_a38x_533[] = {
- /* parameters for 533MHZ */
- /* DDR SDRAM Configuration Register */
- {0x1400, 0x7b00d040, 0xffffffff},
- /* Dunit Control Low Register - kw28 bit12 low (disable CLK1) */
- {0x1404, 0x36301820, 0xffffffff},
- /* DDR SDRAM Timing (Low) Register */
- {0x1408, 0x33137772, 0xffffffff},
- /* DDR SDRAM Timing (High) Register */
- {0x140c, 0x3841199f, 0xffffffff},
- /* DDR SDRAM Address Control Register */
- {0x1410, 0x10330000, 0xffffffff},
- /* DDR SDRAM Open Pages Control Register */
- {0x1414, 0x00000700, 0xffffffff},
- /* Dunit Control High Register (2 :1 - bits 15:12 = 0xd) */
- {0x1424, 0x0060f3ff, 0xffffffff},
- /* Dunit Control High Register */
- {0x1428, 0x000d6720, 0xffffffff},
- /* Dunit Control High Register (2:1 - bit 29 = '1') */
- {0x142c, 0x028c50c3, 0xffffffff},
- {0x147c, 0x0000b571, 0xffffffff},
- /* DDR SDRAM ODT Control (Low) Register */
- {0x1494, 0x00030000, 0xffffffff},
- /* DDR SDRAM ODT Control (High) Register, will be configured at WL */
- {0x1498, 0x00000000, 0xffffffff},
- /* DDR Dunit ODT Control Register */
- {0x149c, 0x00000003, 0xffffffff},
- {0x14a8, 0x00000000, 0xffffffff}, /* */
- {0x14cc, 0xbd09000d, 0xffffffff}, /* */
- {0x1474, 0x00000000, 0xffffffff},
- /* Read Data Sample Delays Register */
- {0x1538, 0x00000707, 0xffffffff},
- /* Read Data Ready Delay Register */
- {0x153c, 0x00000707, 0xffffffff},
- {0x1504, 0xffffffe1, 0xffffffff}, /* */
- {0x150c, 0xffffffe5, 0xffffffff}, /* */
- {0x1514, 0x00000000, 0xffffffff}, /* */
- {0x151c, 0x00000000, 0xffffffff}, /* */
- {0x15d0, 0x00000630, 0xffffffff}, /* MR0 */
- {0x15d4, 0x00000046, 0xffffffff}, /* MR1 */
- {0x15d8, 0x00000008, 0xffffffff}, /* MR2 */
- {0x15dc, 0x00000000, 0xffffffff}, /* MR3 */
- {0x15e0, 0x00000023, 0xffffffff}, /* */
- {0x15e4, 0x00203c18, 0xffffffff}, /* ZQC Configuration Register */
- {0x15ec, 0xf8000019, 0xffffffff}, /* DDR PHY */
- {0x16a0, 0xcc000006, 0xffffffff}, /* Clock Delay */
- {0xe4124, 0x08008073, 0xffffffff}, /* AVS BG default */
- {0, 0, 0}
-};
-
-#endif /* CONFIG_CUSTOMER_BOARD_SUPPORT */
-
-#endif /* SUPPORT_STATIC_DUNIT_CONFIG */
-
-#endif /* _DDR3_A38X_MC_STATIC_H */
diff --git a/drivers/ddr/marvell/a38x/ddr3_debug.c b/drivers/ddr/marvell/a38x/ddr3_debug.c
index 68ab9476ccdf..c14400840e7e 100644
--- a/drivers/ddr/marvell/a38x/ddr3_debug.c
+++ b/drivers/ddr/marvell/a38x/ddr3_debug.c
@@ -867,15 +867,6 @@ static int ddr3_tip_access_atr(u32 dev_num, u32 flag_id, u32 value, u32 **ptr)
case 0x25:
*ptr = (u32 *)&is_adll_calib_before_init;
break;
-#ifdef STATIC_ALGO_SUPPORT
- case 0x26:
- *ptr = (u32 *)&(silicon_delay[0]);
- break;
-
- case 0x27:
- *ptr = (u32 *)&wl_debug_delay;
- break;
-#endif
case 0x28:
*ptr = (u32 *)&is_tune_result;
break;
diff --git a/drivers/ddr/marvell/a38x/ddr3_init.c b/drivers/ddr/marvell/a38x/ddr3_init.c
index 1c5b1f75ca4f..73d984ba66a8 100644
--- a/drivers/ddr/marvell/a38x/ddr3_init.c
+++ b/drivers/ddr/marvell/a38x/ddr3_init.c
@@ -59,20 +59,6 @@ struct dram_modes {
};
struct dram_modes ddr_modes[] = {
-#ifdef SUPPORT_STATIC_DUNIT_CONFIG
- /* Conf name, CPUFreq, Fab_freq, Chip ID, Chip/Board, MC regs*/
-#ifdef CONFIG_CUSTOMER_BOARD_SUPPORT
- {"a38x_customer_0_800", DDR_FREQ_800, 0, 0x0, A38X_CUSTOMER_BOARD_ID0,
- ddr3_customer_800},
- {"a38x_customer_1_800", DDR_FREQ_800, 0, 0x0, A38X_CUSTOMER_BOARD_ID1,
- ddr3_customer_800},
-#else
- {"a38x_533", DDR_FREQ_533, 0, 0x0, MARVELL_BOARD, ddr3_a38x_533},
- {"a38x_667", DDR_FREQ_667, 0, 0x0, MARVELL_BOARD, ddr3_a38x_667},
- {"a38x_800", DDR_FREQ_800, 0, 0x0, MARVELL_BOARD, ddr3_a38x_800},
- {"a38x_933", DDR_FREQ_933, 0, 0x0, MARVELL_BOARD, ddr3_a38x_933},
-#endif
-#endif
};
#endif /* defined(CONFIG_ARMADA_38X) */
@@ -91,9 +77,6 @@ static char *ddr_type = "DDR3";
*/
u8 generic_init_controller = 1;
-#ifdef SUPPORT_STATIC_DUNIT_CONFIG
-static u32 ddr3_get_static_ddr_mode(void);
-#endif
static int ddr3_hws_tune_training_params(u8 dev_num);
/* device revision */
@@ -342,18 +325,6 @@ int ddr3_init(void)
/* Set X-BAR windows for the training sequence */
ddr3_save_and_set_training_windows(win);
-#ifdef SUPPORT_STATIC_DUNIT_CONFIG
- /*
- * Load static controller configuration (in case dynamic/generic init
- * is not enabled
- */
- if (generic_init_controller == 0) {
- ddr3_tip_init_specific_reg_config(0,
- ddr_modes
- [ddr3_get_static_ddr_mode
- ()].regs);
- }
-#endif
/* Tune training algo paramteres */
status = ddr3_hws_tune_training_params(0);
diff --git a/drivers/ddr/marvell/a38x/ddr3_init.h b/drivers/ddr/marvell/a38x/ddr3_init.h
index 05ff62b04154..8cb645ffb59b 100644
--- a/drivers/ddr/marvell/a38x/ddr3_init.h
+++ b/drivers/ddr/marvell/a38x/ddr3_init.h
@@ -8,7 +8,6 @@
#if defined(CONFIG_ARMADA_38X)
#include "ddr3_a38x.h"
-#include "ddr3_a38x_mc_static.h"
#include "ddr3_a38x_topology.h"
#endif
#include "ddr3_hws_hw_training.h"
diff --git a/drivers/ddr/marvell/a38x/ddr3_training.c b/drivers/ddr/marvell/a38x/ddr3_training.c
index c4a150ea7475..fee589b746f0 100644
--- a/drivers/ddr/marvell/a38x/ddr3_training.c
+++ b/drivers/ddr/marvell/a38x/ddr3_training.c
@@ -635,12 +635,6 @@ int hws_ddr3_tip_init_controller(u32 dev_num, struct init_cntr_param *init_cntr_
MASK_ALL_BITS));
}
} else {
-#ifdef STATIC_ALGO_SUPPORT
- CHECK_STATUS(ddr3_tip_static_init_controller(dev_num));
-#if defined(CONFIG_ARMADA_38X) || defined(CONFIG_ARMADA_39X)
- CHECK_STATUS(ddr3_tip_static_phy_init_controller(dev_num));
-#endif
-#endif /* STATIC_ALGO_SUPPORT */
}
for (if_id = 0; if_id <= MAX_INTERFACE_NUM - 1; if_id++) {
@@ -814,25 +808,6 @@ int hws_ddr3_tip_run_alg(u32 dev_num, enum hws_algo_type algo_type)
if (algo_type == ALGO_TYPE_DYNAMIC) {
ret = ddr3_tip_ddr3_auto_tune(dev_num);
} else {
-#ifdef STATIC_ALGO_SUPPORT
- {
- enum hws_ddr_freq freq;
- freq = init_freq;
-
- /* add to mask */
- if (is_adll_calib_before_init != 0) {
- printf("with adll calib before init\n");
- adll_calibration(dev_num, ACCESS_TYPE_MULTICAST,
- 0, freq);
- }
- /*
- * Frequency per interface is not relevant,
- * only interface 0
- */
- ret = ddr3_tip_run_static_alg(dev_num,
- freq);
- }
-#endif
}
if (ret != MV_OK) {
@@ -2027,22 +2002,6 @@ static int ddr3_tip_ddr3_training_main_flow(u32 dev_num)
}
}
-#ifdef STATIC_ALGO_SUPPORT
- if (mask_tune_func & STATIC_LEVELING_MASK_BIT) {
- training_stage = STATIC_LEVELING;
- DEBUG_TRAINING_IP(DEBUG_LEVEL_INFO,
- ("STATIC_LEVELING_MASK_BIT\n"));
- ret = ddr3_tip_run_static_alg(dev_num, freq);
- if (is_reg_dump != 0)
- ddr3_tip_reg_dump(dev_num);
- if (ret != MV_OK) {
- DEBUG_TRAINING_IP(DEBUG_LEVEL_ERROR,
- ("ddr3_tip_run_static_alg failure\n"));
- if (debug_mode == 0)
- return MV_FAIL;
- }
- }
-#endif
if (mask_tune_func & SET_LOW_FREQ_MASK_BIT) {
training_stage = SET_LOW_FREQ;
diff --git a/drivers/ddr/marvell/a38x/ddr3_training_static.c b/drivers/ddr/marvell/a38x/ddr3_training_static.c
index dddbfe17b0f2..1b4bfb2e026c 100644
--- a/drivers/ddr/marvell/a38x/ddr3_training_static.c
+++ b/drivers/ddr/marvell/a38x/ddr3_training_static.c
@@ -25,444 +25,6 @@ u32 g_odt_config_1cs = 0x10000;
u32 g_rtt_nom = 0x44;
u32 g_dic = 0x2;
-#ifdef STATIC_ALGO_SUPPORT
-
-#define PARAM_NOT_CARE 0
-#define MAX_STATIC_SEQ 48
-
-u32 silicon_delay[HWS_MAX_DEVICE_NUM];
-struct hws_tip_static_config_info static_config[HWS_MAX_DEVICE_NUM];
-static reg_data *static_init_controller_config[HWS_MAX_DEVICE_NUM];
-
-/* debug delay in write leveling */
-int wl_debug_delay = 0;
-/* pup register #3 for functional board */
-int function_reg_value = 8;
-u32 silicon;
-
-u32 read_ready_delay_phase_offset[] = { 4, 4, 4, 4, 6, 6, 6, 6 };
-
-static struct cs_element chip_select_map[] = {
- /* CS Value (single only) Num_CS */
- {0, 0},
- {0, 1},
- {1, 1},
- {0, 2},
- {2, 1},
- {0, 2},
- {0, 2},
- {0, 3},
- {3, 1},
- {0, 2},
- {0, 2},
- {0, 3},
- {0, 2},
- {0, 3},
- {0, 3},
- {0, 4}
-};
-
-/*
- * Register static init controller DB
- */
-int ddr3_tip_init_specific_reg_config(u32 dev_num, reg_data *reg_config_arr)
-{
- static_init_controller_config[dev_num] = reg_config_arr;
- return MV_OK;
-}
-
-/*
- * Register static info DB
- */
-int ddr3_tip_init_static_config_db(
- u32 dev_num, struct hws_tip_static_config_info *static_config_info)
-{
- static_config[dev_num].board_trace_arr =
- static_config_info->board_trace_arr;
- static_config[dev_num].package_trace_arr =
- static_config_info->package_trace_arr;
- silicon_delay[dev_num] = static_config_info->silicon_delay;
-
- return MV_OK;
-}
-
-/*
- * Static round trip flow - Calculates the total round trip delay.
- */
-int ddr3_tip_static_round_trip_arr_build(u32 dev_num,
- struct trip_delay_element *table_ptr,
- int is_wl, u32 *round_trip_delay_arr)
-{
- u32 bus_index, global_bus;
- u32 if_id;
- u32 bus_per_interface;
- int sign;
- u32 temp;
- u32 board_trace;
- struct trip_delay_element *pkg_delay_ptr;
- struct hws_topology_map *tm = ddr3_get_topology_map();
-
- /*
- * In WL we calc the diff between Clock to DQs in RL we sum the round
- * trip of Clock and DQs
- */
- sign = (is_wl) ? -1 : 1;
-
- bus_per_interface = GET_TOPOLOGY_NUM_OF_BUSES();
-
- for (if_id = 0; if_id <= MAX_INTERFACE_NUM - 1; if_id++) {
- VALIDATE_ACTIVE(tm->if_act_mask, if_id);
- for (bus_index = 0; bus_index < bus_per_interface;
- bus_index++) {
- VALIDATE_ACTIVE(tm->bus_act_mask, bus_index);
- global_bus = (if_id * bus_per_interface) + bus_index;
-
- /* calculate total trip delay (package and board) */
- board_trace = (table_ptr[global_bus].dqs_delay * sign) +
- table_ptr[global_bus].ck_delay;
- temp = (board_trace * 163) / 1000;
-
- /* Convert the length to delay in psec units */
- pkg_delay_ptr =
- static_config[dev_num].package_trace_arr;
- round_trip_delay_arr[global_bus] = temp +
- (int)(pkg_delay_ptr[global_bus].dqs_delay *
- sign) +
- (int)pkg_delay_ptr[global_bus].ck_delay +
- (int)((is_wl == 1) ? wl_debug_delay :
- (int)silicon_delay[dev_num]);
- DEBUG_TRAINING_STATIC_IP(
- DEBUG_LEVEL_TRACE,
- ("Round Trip Build round_trip_delay_arr[0x%x]: 0x%x temp 0x%x\n",
- global_bus, round_trip_delay_arr[global_bus],
- temp));
- }
- }
-
- return MV_OK;
-}
-
-/*
- * Write leveling for static flow - calculating the round trip delay of the
- * DQS signal.
- */
-int ddr3_tip_write_leveling_static_config(u32 dev_num, u32 if_id,
- enum hws_ddr_freq frequency,
- u32 *round_trip_delay_arr)
-{
- u32 bus_index; /* index to the bus loop */
- u32 bus_start_index;
- u32 bus_per_interface;
- u32 phase = 0;
- u32 adll = 0, adll_cen, adll_inv, adll_final;
- u32 adll_period = MEGA / freq_val[frequency] / 64;
-
- DEBUG_TRAINING_STATIC_IP(DEBUG_LEVEL_TRACE,
- ("ddr3_tip_write_leveling_static_config\n"));
- DEBUG_TRAINING_STATIC_IP(
- DEBUG_LEVEL_TRACE,
- ("dev_num 0x%x IF 0x%x freq %d (adll_period 0x%x)\n",
- dev_num, if_id, frequency, adll_period));
-
- bus_per_interface = GET_TOPOLOGY_NUM_OF_BUSES();
- bus_start_index = if_id * bus_per_interface;
- for (bus_index = bus_start_index;
- bus_index < (bus_start_index + bus_per_interface); bus_index++) {
- VALIDATE_ACTIVE(tm->bus_act_mask, bus_index);
- phase = round_trip_delay_arr[bus_index] / (32 * adll_period);
- adll = (round_trip_delay_arr[bus_index] -
- (phase * 32 * adll_period)) / adll_period;
- adll = (adll > 31) ? 31 : adll;
- adll_cen = 16 + adll;
- adll_inv = adll_cen / 32;
- adll_final = adll_cen - (adll_inv * 32);
- adll_final = (adll_final > 31) ? 31 : adll_final;
-
- DEBUG_TRAINING_STATIC_IP(DEBUG_LEVEL_TRACE,
- ("\t%d - phase 0x%x adll 0x%x\n",
- bus_index, phase, adll));
- /*
- * Writing to all 4 phy of Interface number,
- * bit 0 \96 4 \96 ADLL, bit 6-8 phase
- */
- CHECK_STATUS(ddr3_tip_bus_read_modify_write
- (dev_num, ACCESS_TYPE_UNICAST, if_id,
- (bus_index % 4), DDR_PHY_DATA,
- PHY_WRITE_DELAY(cs),
- ((phase << 6) + (adll & 0x1f)), 0x1df));
- CHECK_STATUS(ddr3_tip_bus_write
- (dev_num, ACCESS_TYPE_UNICAST, if_id,
- ACCESS_TYPE_UNICAST, (bus_index % 4),
- DDR_PHY_DATA, WRITE_CENTRALIZATION_PHY_REG,
- ((adll_inv & 0x1) << 5) + adll_final));
- }
-
- return MV_OK;
-}
-
-/*
- * Read leveling for static flow
- */
-int ddr3_tip_read_leveling_static_config(u32 dev_num,
- u32 if_id,
- enum hws_ddr_freq frequency,
- u32 *total_round_trip_delay_arr)
-{
- u32 cs, data0, data1, data3 = 0;
- u32 bus_index; /* index to the bus loop */
- u32 bus_start_index;
- u32 phase0, phase1, max_phase;
- u32 adll0, adll1;
- u32 cl_value;
- u32 min_delay;
- u32 sdr_period = MEGA / freq_val[frequency];
- u32 ddr_period = MEGA / freq_val[frequency] / 2;
- u32 adll_period = MEGA / freq_val[frequency] / 64;
- enum hws_speed_bin speed_bin_index;
- u32 rd_sample_dly[MAX_CS_NUM] = { 0 };
- u32 rd_ready_del[MAX_CS_NUM] = { 0 };
- u32 bus_per_interface = GET_TOPOLOGY_NUM_OF_BUSES();
- struct hws_topology_map *tm = ddr3_get_topology_map();
-
- DEBUG_TRAINING_STATIC_IP(DEBUG_LEVEL_TRACE,
- ("ddr3_tip_read_leveling_static_config\n"));
- DEBUG_TRAINING_STATIC_IP(DEBUG_LEVEL_TRACE,
- ("dev_num 0x%x ifc 0x%x freq %d\n", dev_num,
- if_id, frequency));
- DEBUG_TRAINING_STATIC_IP(
- DEBUG_LEVEL_TRACE,
- ("Sdr_period 0x%x Ddr_period 0x%x adll_period 0x%x\n",
- sdr_period, ddr_period, adll_period));
-
- if (tm->interface_params[first_active_if].memory_freq ==
- frequency) {
- cl_value = tm->interface_params[first_active_if].cas_l;
- DEBUG_TRAINING_STATIC_IP(DEBUG_LEVEL_TRACE,
- ("cl_value 0x%x\n", cl_value));
- } else {
- speed_bin_index = tm->interface_params[if_id].speed_bin_index;
- cl_value = cas_latency_table[speed_bin_index].cl_val[frequency];
- DEBUG_TRAINING_STATIC_IP(DEBUG_LEVEL_TRACE,
- ("cl_value 0x%x speed_bin_index %d\n",
- cl_value, speed_bin_index));
- }
-
- bus_start_index = if_id * bus_per_interface;
-
- for (bus_index = bus_start_index;
- bus_index < (bus_start_index + bus_per_interface);
- bus_index += 2) {
- VALIDATE_ACTIVE(tm->bus_act_mask, bus_index);
- cs = chip_select_map[
- tm->interface_params[if_id].as_bus_params[
- (bus_index % 4)].cs_bitmask].cs_num;
-
- /* read sample delay calculation */
- min_delay = (total_round_trip_delay_arr[bus_index] <
- total_round_trip_delay_arr[bus_index + 1]) ?
- total_round_trip_delay_arr[bus_index] :
- total_round_trip_delay_arr[bus_index + 1];
- /* round down */
- rd_sample_dly[cs] = 2 * (min_delay / (sdr_period * 2));
- DEBUG_TRAINING_STATIC_IP(
- DEBUG_LEVEL_TRACE,
- ("\t%d - min_delay 0x%x cs 0x%x rd_sample_dly[cs] 0x%x\n",
- bus_index, min_delay, cs, rd_sample_dly[cs]));
-
- /* phase calculation */
- phase0 = (total_round_trip_delay_arr[bus_index] -
- (sdr_period * rd_sample_dly[cs])) / (ddr_period);
- phase1 = (total_round_trip_delay_arr[bus_index + 1] -
- (sdr_period * rd_sample_dly[cs])) / (ddr_period);
- max_phase = (phase0 > phase1) ? phase0 : phase1;
- DEBUG_TRAINING_STATIC_IP(
- DEBUG_LEVEL_TRACE,
- ("\tphase0 0x%x phase1 0x%x max_phase 0x%x\n",
- phase0, phase1, max_phase));
-
- /* ADLL calculation */
- adll0 = (u32)((total_round_trip_delay_arr[bus_index] -
- (sdr_period * rd_sample_dly[cs]) -
- (ddr_period * phase0)) / adll_period);
- adll0 = (adll0 > 31) ? 31 : adll0;
- adll1 = (u32)((total_round_trip_delay_arr[bus_index + 1] -
- (sdr_period * rd_sample_dly[cs]) -
- (ddr_period * phase1)) / adll_period);
- adll1 = (adll1 > 31) ? 31 : adll1;
-
- /* The Read delay close the Read FIFO */
- rd_ready_del[cs] = rd_sample_dly[cs] +
- read_ready_delay_phase_offset[max_phase];
- DEBUG_TRAINING_STATIC_IP(
- DEBUG_LEVEL_TRACE,
- ("\tadll0 0x%x adll1 0x%x rd_ready_del[cs] 0x%x\n",
- adll0, adll1, rd_ready_del[cs]));
-
- /*
- * Write to the phy of Interface (bit 0 \96 4 \96 ADLL,
- * bit 6-8 phase)
- */
- data0 = ((phase0 << 6) + (adll0 & 0x1f));
- data1 = ((phase1 << 6) + (adll1 & 0x1f));
-
- CHECK_STATUS(ddr3_tip_bus_read_modify_write
- (dev_num, ACCESS_TYPE_UNICAST, if_id,
- (bus_index % 4), DDR_PHY_DATA, PHY_READ_DELAY(cs),
- data0, 0x1df));
- CHECK_STATUS(ddr3_tip_bus_read_modify_write
- (dev_num, ACCESS_TYPE_UNICAST, if_id,
- ((bus_index + 1) % 4), DDR_PHY_DATA,
- PHY_READ_DELAY(cs), data1, 0x1df));
- }
-
- for (bus_index = 0; bus_index < bus_per_interface; bus_index++) {
- VALIDATE_ACTIVE(tm->bus_act_mask, bus_index);
- CHECK_STATUS(ddr3_tip_bus_read_modify_write
- (dev_num, ACCESS_TYPE_UNICAST, if_id,
- bus_index, DDR_PHY_DATA, 0x3, data3, 0x1f));
- }
- CHECK_STATUS(ddr3_tip_if_write
- (dev_num, ACCESS_TYPE_UNICAST, if_id,
- READ_DATA_SAMPLE_DELAY,
- (rd_sample_dly[0] + cl_value) + (rd_sample_dly[1] << 8),
- MASK_ALL_BITS));
-
- /* Read_ready_del0 bit 0-4 , CS bits 8-12 */
- CHECK_STATUS(ddr3_tip_if_write
- (dev_num, ACCESS_TYPE_UNICAST, if_id,
- READ_DATA_READY_DELAY,
- rd_ready_del[0] + (rd_ready_del[1] << 8) + cl_value,
- MASK_ALL_BITS));
-
- return MV_OK;
-}
-
-/*
- * DDR3 Static flow
- */
-int ddr3_tip_run_static_alg(u32 dev_num, enum hws_ddr_freq freq)
-{
- u32 if_id = 0;
- struct trip_delay_element *table_ptr;
- u32 wl_total_round_trip_delay_arr[MAX_TOTAL_BUS_NUM];
- u32 rl_total_round_trip_delay_arr[MAX_TOTAL_BUS_NUM];
- struct init_cntr_param init_cntr_prm;
- int ret;
- struct hws_topology_map *tm = ddr3_get_topology_map();
-
- DEBUG_TRAINING_STATIC_IP(DEBUG_LEVEL_TRACE,
- ("ddr3_tip_run_static_alg"));
-
- init_cntr_prm.do_mrs_phy = 1;
- init_cntr_prm.is_ctrl64_bit = 0;
- init_cntr_prm.init_phy = 1;
- ret = hws_ddr3_tip_init_controller(dev_num, &init_cntr_prm);
- if (ret != MV_OK) {
- DEBUG_TRAINING_STATIC_IP(
- DEBUG_LEVEL_ERROR,
- ("hws_ddr3_tip_init_controller failure\n"));
- }
-
- /* calculate the round trip delay for Write Leveling */
- table_ptr = static_config[dev_num].board_trace_arr;
- CHECK_STATUS(ddr3_tip_static_round_trip_arr_build
- (dev_num, table_ptr, 1,
- wl_total_round_trip_delay_arr));
- /* calculate the round trip delay for Read Leveling */
- CHECK_STATUS(ddr3_tip_static_round_trip_arr_build
- (dev_num, table_ptr, 0,
- rl_total_round_trip_delay_arr));
-
- for (if_id = 0; if_id <= MAX_INTERFACE_NUM - 1; if_id++) {
- /* check if the interface is enabled */
- VALIDATE_ACTIVE(tm->if_act_mask, if_id);
- /*
- * Static frequency is defined according to init-frequency
- * (not target)
- */
- DEBUG_TRAINING_STATIC_IP(DEBUG_LEVEL_TRACE,
- ("Static IF %d freq %d\n",
- if_id, freq));
- CHECK_STATUS(ddr3_tip_write_leveling_static_config
- (dev_num, if_id, freq,
- wl_total_round_trip_delay_arr));
- CHECK_STATUS(ddr3_tip_read_leveling_static_config
- (dev_num, if_id, freq,
- rl_total_round_trip_delay_arr));
- }
-
- return MV_OK;
-}
-
-/*
- * Init controller for static flow
- */
-int ddr3_tip_static_init_controller(u32 dev_num)
-{
- u32 index_cnt = 0;
-
- DEBUG_TRAINING_STATIC_IP(DEBUG_LEVEL_TRACE,
- ("ddr3_tip_static_init_controller\n"));
- while (static_init_controller_config[dev_num][index_cnt].reg_addr !=
- 0) {
- CHECK_STATUS(ddr3_tip_if_write
- (dev_num, ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE,
- static_init_controller_config[dev_num][index_cnt].
- reg_addr,
- static_init_controller_config[dev_num][index_cnt].
- reg_data,
- static_init_controller_config[dev_num][index_cnt].
- reg_mask));
-
- DEBUG_TRAINING_STATIC_IP(DEBUG_LEVEL_TRACE,
- ("Init_controller index_cnt %d\n",
- index_cnt));
- index_cnt++;
- }
-
- return MV_OK;
-}
-
-int ddr3_tip_static_phy_init_controller(u32 dev_num)
-{
- DEBUG_TRAINING_STATIC_IP(DEBUG_LEVEL_TRACE,
- ("Phy Init Controller 2\n"));
- CHECK_STATUS(ddr3_tip_bus_write
- (dev_num, ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE,
- ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE, DDR_PHY_DATA, 0xa4,
- 0x3dfe));
-
- DEBUG_TRAINING_STATIC_IP(DEBUG_LEVEL_TRACE,
- ("Phy Init Controller 3\n"));
- CHECK_STATUS(ddr3_tip_bus_write
- (dev_num, ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE,
- ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE, DDR_PHY_DATA, 0xa6,
- 0xcb2));
-
- DEBUG_TRAINING_STATIC_IP(DEBUG_LEVEL_TRACE,
- ("Phy Init Controller 4\n"));
- CHECK_STATUS(ddr3_tip_bus_write
- (dev_num, ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE,
- ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE, DDR_PHY_DATA, 0xa9,
- 0));
-
- DEBUG_TRAINING_STATIC_IP(DEBUG_LEVEL_TRACE,
- ("Static Receiver Calibration\n"));
- CHECK_STATUS(ddr3_tip_bus_write
- (dev_num, ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE,
- ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE, DDR_PHY_DATA, 0xd0,
- 0x1f));
-
- DEBUG_TRAINING_STATIC_IP(DEBUG_LEVEL_TRACE,
- ("Static V-REF Calibration\n"));
- CHECK_STATUS(ddr3_tip_bus_write
- (dev_num, ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE,
- ACCESS_TYPE_MULTICAST, PARAM_NOT_CARE, DDR_PHY_DATA, 0xa8,
- 0x434));
-
- return MV_OK;
-}
-#endif
/*
* Configure phy (called by static init controller) for static flow
--
2.17.0
More information about the U-Boot
mailing list