[U-Boot] [PATCH 3/3] serial: Migrate CONFIG_ARM_DCC to Kconfig

[Alexey Brodkin]

Hi gents,

On Sun, 2018-04-08 at 00:27 +0300, Tuomas Tynkkynen wrote:
> Signed-off-by: Tuomas Tynkkynen <tuomas at tuxera.com>
> ---
>  arch/arm/Kconfig                | 2 ++
>  drivers/serial/Kconfig          | 5 +++++
>  include/configs/xilinx_zynqmp.h | 1 -
>  include/configs/zynq-common.h   | 2 --
>  scripts/config_whitelist.txt    | 1 -
>  5 files changed, 7 insertions(+), 4 deletions(-)

Not sure who's the right person to review and accept this one.
I'm not the one for sure :)

-Alexey

> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
> index 190f883aa8..44a4471b47 100644
> --- a/arch/arm/Kconfig
> +++ b/arch/arm/Kconfig
> @@ -776,6 +776,7 @@ config ARCH_ZYNQ
>  	select CLK
>  	select SPL_CLK if SPL
>  	select CLK_ZYNQ
> +	imply ARM_DCC
>  	imply CMD_CLK
>  	imply FAT_WRITE
>  	imply CMD_SPL
> @@ -792,6 +793,7 @@ config ARCH_ZYNQMP
>  	select SPL_BOARD_INIT if SPL
>  	select SPL_CLK if SPL
>  	select DM_USB if USB
> +	imply ARM_DCC
>  	imply FAT_WRITE
>  
>  config TEGRA
> diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
> index 9387b642b3..41ce6dec8c 100644
> --- a/drivers/serial/Kconfig
> +++ b/drivers/serial/Kconfig
> @@ -432,6 +432,11 @@ config AR933X_UART
>  	  tree binding to operate, please refer to the document at
>  	  doc/device-tree-bindings/serial/qca,ar9330-uart.txt.
>  
> +config ARM_DCC
> +	bool "ARM DCC (Debug Communications Channel) serial console support"
> +	help
> +	  Select this to enable a serial port using the ARM JTAG DCC port.
> +
>  config ATMEL_USART
>  	bool "Atmel USART support"
>  	help
> diff --git a/include/configs/xilinx_zynqmp.h b/include/configs/xilinx_zynqmp.h
> index 8c0b5d9c06..312a2a83ff 100644
> --- a/include/configs/xilinx_zynqmp.h
> +++ b/include/configs/xilinx_zynqmp.h
> @@ -42,7 +42,6 @@
>  #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 0x2000000)
>  
>  /* Serial setup */
> -#define CONFIG_ARM_DCC
>  #define CONFIG_CPU_ARMV8
>  
>  #define CONFIG_SYS_BAUDRATE_TABLE \
> diff --git a/include/configs/zynq-common.h b/include/configs/zynq-common.h
> index 554fb66634..699c91d3c5 100644
> --- a/include/configs/zynq-common.h
> +++ b/include/configs/zynq-common.h
> @@ -32,8 +32,6 @@
>  #define CONFIG_SYS_BAUDRATE_TABLE  \
>  	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
>  
> -#define CONFIG_ARM_DCC
> -
>  /* Ethernet driver */
>  #if defined(CONFIG_ZYNQ_GEM)
>  # define CONFIG_MII
> diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt
> index 30da0122f0..417a978f0a 100644
> --- a/scripts/config_whitelist.txt
> +++ b/scripts/config_whitelist.txt
> @@ -59,7 +59,6 @@ CONFIG_ARMV7_SECURE_MAX_SIZE
>  CONFIG_ARMV7_SECURE_RESERVE_SIZE
>  CONFIG_ARMV8_SWITCH_TO_EL1
>  CONFIG_ARM_ARCH_CP15_ERRATA
> -CONFIG_ARM_DCC
>  CONFIG_ARM_FREQ
>  CONFIG_ARM_GIC_BASE_ADDRESS
>  CONFIG_ARM_PL180_MMCI_BASE