[U-Boot] [PATCH 4/7] ARM: k2g: add a workaround to reset the phy

[Murali Karicheri]

This patch adds a workaround to reset the phy one time during boot
using GPIO0 pin 10 to make sure, the Phy latches the configuration
from the input pins correctly.

Signed-off-by: Murali Karicheri <m-karicheri2 at ti.com>
---
 .../arm/mach-keystone/include/mach/hardware-k2g.h |  3 +++
 board/ti/ks2_evm/board_k2g.c                      | 15 +++++++++++++++
 2 files changed, 18 insertions(+)

diff --git a/arch/arm/mach-keystone/include/mach/hardware-k2g.h b/arch/arm/mach-keystone/include/mach/hardware-k2g.h
index 8b902641ec..971c081bb3 100644
--- a/arch/arm/mach-keystone/include/mach/hardware-k2g.h
+++ b/arch/arm/mach-keystone/include/mach/hardware-k2g.h
@@ -69,9 +69,12 @@
 
 #define K2G_GPIO0_BASE			0X02603000
 #define K2G_GPIO1_BASE			0X0260a000
+#define K2G_GPIO0_BANK0_BASE		K2G_GPIO0_BASE + 0x10
 #define K2G_GPIO1_BANK2_BASE		K2G_GPIO1_BASE + 0x38
 #define K2G_GPIO_DIR_OFFSET		0x0
+#define K2G_GPIO_OUTDATA_OFFSET		0x4
 #define K2G_GPIO_SETDATA_OFFSET		0x8
+#define K2G_GPIO_CLRDATA_OFFSET		0xC
 
 /* BOOTCFG RESETMUX8 */
 #define KS2_RSTMUX8			(KS2_DEVICE_STATE_CTRL_BASE + 0x328)
diff --git a/board/ti/ks2_evm/board_k2g.c b/board/ti/ks2_evm/board_k2g.c
index 39a782e479..6d0fc21c67 100644
--- a/board/ti/ks2_evm/board_k2g.c
+++ b/board/ti/ks2_evm/board_k2g.c
@@ -315,6 +315,21 @@ int embedded_dtb_select(void)
 			     BIT(9));
 		setbits_le32(K2G_GPIO1_BANK2_BASE + K2G_GPIO_SETDATA_OFFSET,
 			     BIT(9));
+	} else if (board_is_k2g_ice()) {
+		/* GBE Phy workaround. For Phy to latch the input
+		 * configuration, a GPIO reset is asserted at the
+		 * Phy reset pin to latch configuration correctly after SoC
+		 * reset. GPIO0 Pin 10 (Ball AA20) is used for this on ICE
+		 * board. Just do a low to high transition.
+		 */
+		clrbits_le32(K2G_GPIO0_BANK0_BASE + K2G_GPIO_DIR_OFFSET,
+			     BIT(10));
+		setbits_le32(K2G_GPIO0_BANK0_BASE + K2G_GPIO_CLRDATA_OFFSET,
+			     BIT(10));
+		/* Delay just to get a transition to high */
+		udelay(100);
+		setbits_le32(K2G_GPIO0_BANK0_BASE + K2G_GPIO_SETDATA_OFFSET,
+			     BIT(10));
 	}
 
 	return 0;
-- 
2.17.0