[U-Boot] [PATCH 10/10] board: sopine: Enable SPI/SPI-FLASH
Jagan Teki
jagan at amarulasolutions.com
Wed Feb 13 10:27:28 UTC 2019
On Wed, Feb 13, 2019 at 6:53 AM André Przywara <andre.przywara at arm.com> wrote:
>
> On 09/02/2019 13:15, Jagan Teki wrote:
> > Sopine has Winbond SPI flash, so enable the same to use
> > flash on Sopine board.
> >
> > Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
> > ---
> > arch/arm/dts/sun50i-a64-sopine-baseboard-u-boot.dtsi | 12 ++++++++++++
> > configs/sopine_baseboard_defconfig | 4 ++++
> > 2 files changed, 16 insertions(+)
> > create mode 100644 arch/arm/dts/sun50i-a64-sopine-baseboard-u-boot.dtsi
> >
> > diff --git a/arch/arm/dts/sun50i-a64-sopine-baseboard-u-boot.dtsi b/arch/arm/dts/sun50i-a64-sopine-baseboard-u-boot.dtsi
> > new file mode 100644
> > index 0000000000..02b1ae046e
> > --- /dev/null
> > +++ b/arch/arm/dts/sun50i-a64-sopine-baseboard-u-boot.dtsi
> > @@ -0,0 +1,12 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Copyright (C) 2018 Jagan Teki <jagan at amarulasolutions.com>
> > + */
> > +
> > +#include "sunxi-u-boot.dtsi"
> > +
> > +/ {
> > + aliases {
> > + spi0 = &spi0;
> > + };
> > +};
> > diff --git a/configs/sopine_baseboard_defconfig b/configs/sopine_baseboard_defconfig
> > index 9d7e3a2b6c..a94e3c21fd 100644
> > --- a/configs/sopine_baseboard_defconfig
> > +++ b/configs/sopine_baseboard_defconfig
> > @@ -10,11 +10,15 @@ CONFIG_MMC0_CD_PIN=""
> > CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> > CONFIG_SPL_SPI_SUNXI=y
> > CONFIG_NR_DRAM_BANKS=1
> > +CONFIG_CMD_SF=y
> > # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> > # CONFIG_CMD_FLASH is not set
> > # CONFIG_SPL_DOS_PARTITION is not set
> > # CONFIG_SPL_EFI_PARTITION is not set
> > CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-sopine-baseboard"
> > +CONFIG_DM_SPI=y
> > +CONFIG_DM_SPI_FLASH=y
> > +CONFIG_SPI_FLASH_WINBOND=y
>
> That isn't enough, you need CONFIG_SPI=y as well, otherwise the build fails.
> I'd suggest to move DM_SPI=y and DM_SPI_FLASH=y to arch/arm/Kconfig (as
> mentioned in the previous mail) and keep CONFIG_SPI=y here, to enable
> SPI support for a particular board. Then keep ..._WINBOND here to set
> the flash chip. For which you need CONFIG_SPI_FLASH, I believe. Which
> sounds somewhat weird.
Did the similar work already[1], plan to use these on top of these set.
[1] https://patchwork.ozlabs.org/patch/1039175/
More information about the U-Boot
mailing list