[U-Boot] [PATCH v1 11/22] colibri_vf: migrate fec, esdhc, nfc and usb to driver model
Marcel Ziswiler
marcel at ziswiler.com
Fri Feb 15 22:20:27 UTC 2019
From: Marcel Ziswiler <marcel.ziswiler at toradex.com>
Migrate FEC, ESDHC, NFC and USB to driver model.
While at it also do no longer enable optional I2C clock in board file as
the generic clock code now handles this. Note for space reason and as
it is not required just for booting we do not enable I2C in U-Boot by
default.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler at toradex.com>
---
board/toradex/colibri_vf/colibri_vf.c | 83 +--------------------------
configs/colibri_vf_defconfig | 5 ++
include/configs/colibri_vf.h | 13 +----
3 files changed, 7 insertions(+), 94 deletions(-)
diff --git a/board/toradex/colibri_vf/colibri_vf.c b/board/toradex/colibri_vf/colibri_vf.c
index c9de3c0c76..421a4791a1 100644
--- a/board/toradex/colibri_vf/colibri_vf.c
+++ b/board/toradex/colibri_vf/colibri_vf.c
@@ -16,24 +16,16 @@
#include <asm/gpio.h>
#include <asm/io.h>
#include <fdt_support.h>
-#include <fsl_esdhc.h>
#include <fsl_dcu_fb.h>
#include <g_dnl.h>
-#include <i2c.h>
#include <jffs2/load_kernel.h>
-#include <miiphy.h>
-#include <mmc.h>
#include <mtd_node.h>
-#include <netdev.h>
#include <usb.h>
#include "../common/tdx-common.h"
DECLARE_GLOBAL_DATA_PTR;
-#define USB_PEN_GPIO 83
-#define USB_CDET_GPIO 102
-
static struct ddrmc_cr_setting colibri_vf_cr_settings[] = {
/* AXI */
{ DDRMC_CR117_AXI0_W_PRI(0) | DDRMC_CR117_AXI0_R_PRI(0), 117 },
@@ -238,25 +230,6 @@ static void setup_tcon(void)
}
#endif
-#ifdef CONFIG_FSL_ESDHC
-struct fsl_esdhc_cfg esdhc_cfg[1] = {
- {ESDHC1_BASE_ADDR},
-};
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- /* eSDHC1 is always present */
- return 1;
-}
-
-int board_mmc_init(bd_t *bis)
-{
- esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
-
- return fsl_esdhc_initialize(bis, &esdhc_cfg[0]);
-}
-#endif
-
static inline int is_colibri_vf61(void)
{
struct mscm *mscm = (struct mscm *)MSCM_BASE_ADDR;
@@ -289,7 +262,7 @@ static void clock_init(void)
CCM_CCGR3_ANADIG_CTRL_MASK | CCM_CCGR3_SCSC_CTRL_MASK);
clrsetbits_le32(&ccm->ccgr4, CCM_REG_CTRL_MASK,
CCM_CCGR4_WKUP_CTRL_MASK | CCM_CCGR4_CCM_CTRL_MASK |
- CCM_CCGR4_GPC_CTRL_MASK | CCM_CCGR4_I2C0_CTRL_MASK);
+ CCM_CCGR4_GPC_CTRL_MASK);
clrsetbits_le32(&ccm->ccgr6, CCM_REG_CTRL_MASK,
CCM_CCGR6_OCOTP_CTRL_MASK | CCM_CCGR6_DDRMC_CTRL_MASK);
clrsetbits_le32(&ccm->ccgr7, CCM_REG_CTRL_MASK,
@@ -378,14 +351,6 @@ static void mscm_init(void)
writew(MSCM_IRSPRC_CP0_EN, &mscmir->irsprc[i]);
}
-int board_phy_config(struct phy_device *phydev)
-{
- if (phydev->drv->config)
- phydev->drv->config(phydev);
-
- return 0;
-}
-
int board_early_init_f(void)
{
clock_init();
@@ -432,13 +397,8 @@ int board_init(void)
* so we must use the external oscillator in order
* to maintain correct time in the hwclock
*/
-
setbits_le32(&scsc->sosc_ctr, SCSC_SOSC_CTR_SOSC_EN);
-#ifdef CONFIG_USB_EHCI_VF
- gpio_request(USB_CDET_GPIO, "usb-cdet-gpio");
-#endif
-
return 0;
}
@@ -474,44 +434,3 @@ int ft_board_setup(void *blob, bd_t *bd)
return ft_common_board_setup(blob, bd);
}
#endif
-
-#ifdef CONFIG_USB_EHCI_VF
-int board_ehci_hcd_init(int port)
-{
- switch (port) {
- case 0:
- /* USBC does not have PEN, also configured as USB client only */
- break;
- case 1:
- gpio_request(USB_PEN_GPIO, "usb-pen-gpio");
- gpio_direction_output(USB_PEN_GPIO, 0);
- break;
- }
- return 0;
-}
-
-int board_usb_phy_mode(int port)
-{
- switch (port) {
- case 0:
- /*
- * Port 0 is used only in client mode on Colibri Vybrid modules
- * Check for state of USB client gpio pin and accordingly return
- * USB_INIT_DEVICE or USB_INIT_HOST.
- */
- if (gpio_get_value(USB_CDET_GPIO))
- return USB_INIT_DEVICE;
- else
- return USB_INIT_HOST;
- case 1:
- /* Port 1 is used only in host mode on Colibri Vybrid modules */
- return USB_INIT_HOST;
- default:
- /*
- * There are only two USB controllers on Vybrid. Ideally we will
- * not reach here. However return USB_INIT_HOST if we do.
- */
- return USB_INIT_HOST;
- }
-}
-#endif
diff --git a/configs/colibri_vf_defconfig b/configs/colibri_vf_defconfig
index 9a91cb4b82..344fe77234 100644
--- a/configs/colibri_vf_defconfig
+++ b/configs/colibri_vf_defconfig
@@ -56,13 +56,18 @@ CONFIG_DM=y
CONFIG_DFU_NAND=y
CONFIG_DM_GPIO=y
CONFIG_VYBRID_GPIO=y
+CONFIG_DM_MMC=y
# CONFIG_MMC_HW_PARTITIONING is not set
CONFIG_FSL_ESDHC=y
+CONFIG_MTD=y
CONFIG_NAND_VF610_NFC=y
+CONFIG_NAND_VF610_NFC_DT=y
CONFIG_SYS_NAND_VF610_NFC_60_ECC_BYTES=y
CONFIG_MTD_UBI_FASTMAP=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
+CONFIG_DM_ETH=y
+CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_VYBRID=y
diff --git a/include/configs/colibri_vf.h b/include/configs/colibri_vf.h
index e7b786e48b..1acc6e5056 100644
--- a/include/configs/colibri_vf.h
+++ b/include/configs/colibri_vf.h
@@ -1,6 +1,6 @@
/* SPDX-License-Identifier: GPL-2.0+ */
/*
- * Copyright 2015-2016 Toradex, Inc.
+ * Copyright 2015-2019 Toradex, Inc.
*
* Configuration settings for the Toradex VF50/VF61 modules.
*
@@ -36,17 +36,6 @@
/* NAND support */
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE NFC_BASE_ADDR
-
-/* Dynamic MTD partition support */
-
-#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-#define CONFIG_SYS_FSL_ESDHC_NUM 1
-
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE ENET1_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE RMII
-#define CONFIG_FEC_MXC_PHYADDR 0
#define CONFIG_IPADDR 192.168.10.2
#define CONFIG_NETMASK 255.255.255.0
--
2.20.1
More information about the U-Boot
mailing list