[U-Boot] [PATCH v3 0/9] arm: exynos: Fix reboot on Odroid HC1

[Anand Moon]

Hi Krzysztof,

Please add my. on Odroid HC1

Tested-by: Anand Moon <linux.amoon at gmail.com>

Best Regards
-Anand

On Sat, 16 Feb 2019 at 15:16, Krzysztof Kozlowski <krzk at kernel.org> wrote:
>
> Hi,
>
> Changes since v2
> ================
> 1. Add Lukasz review tags.
> 2. Patch 7: Return on error, as suggested by Simon.
> 2. Patch 3: Use IS_ENABLED() to run revision detection only
>    once - either during late display board or misc_init_r.
>
> Changes since v1
> ================
> 1. Move fixes to beginning of patchset.
> 2. Patch 3: Rework the idea - split revision detection to be executed later.
> 3. Patch 4: New patch.
> 4. Patch 6: Apply Simon's comments.
> 5. Patch 6: Do not delay when changing voltage if regulator is disabled.
> 6. Patch 6: Do not delay when disabling the regulator.
>
>
> Description
> ===========
> Odroid HC1 does not reboot properly (at least from SD card but
> I do not expect difference on eMMC), if LDO4/VDD_ADC was turned
> off by Linux kernel.  This condition happens so far always, because
> Linux kernel did not enable ADC on Odroid HC1, therefore the
> VDD_ADC regulator was turned off as unused.
>
> The issue is in detection of revision which later is used to load
> proper DTB.
>
> The revision is obtained by ADC read of a voltage depending on VDD_ADC.
> Therefore:
> 1. VDD_ADC has to be turned on (but board detection happens before
>    power is initialized),
> 2. Turning VDD_ADC should wait with ramp delay,
> 3. Reading the value from ADC should wait for it to stabilize.
>
> Tested on Odroid XU3-Lite and Odroid HC1.
>
> Commends and testing are welcomed.
>
> Best regards,
> Krzysztof
>
> Krzysztof Kozlowski (9):
>   adc: exynos-adc: Fix wrong bit operation used to stop the ADC
>   power: regulator: s2mps11: Fix step for LDO27 and LDO35
>   arm: exynos: Detect revision later, when all resources are ready
>   arm: exynos: odroid-xu3: Display info late to have proper type
>   arm: exynos: Wait till ADC stabilizes before checking Odroid HC1
>     revision
>   regulator: Add support for ramp delay
>   power: regulator: s2mps11: Add enable delay
>   arm: dts: exynos: Add supply for ADC block to Odroid XU3 family
>   arm: dts: exynos: Add ramp delay property to LDO regulators to Odroid
>     XU3 family
>
>  arch/arm/dts/exynos5422-odroidxu3.dts         | 20 +++++++
>  board/samsung/common/board.c                  | 24 ++++++++-
>  board/samsung/common/exynos5-dt-types.c       | 54 +++++++++++++++++--
>  board/samsung/odroid/odroid.c                 |  8 +++
>  configs/odroid-xu3_defconfig                  |  2 +
>  .../regulator/regulator.txt                   |  2 +
>  drivers/adc/exynos-adc.c                      |  2 +-
>  drivers/power/regulator/regulator-uclass.c    | 47 +++++++++++++++-
>  drivers/power/regulator/s2mps11_regulator.c   | 15 +++++-
>  include/power/regulator.h                     |  2 +
>  include/samsung/misc.h                        |  1 +
>  11 files changed, 167 insertions(+), 10 deletions(-)
>
> --
> 2.17.1
>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot