[U-Boot] [PATCH v4] dm: spi: Read default speed and mode values from DT

Patrick Delaunay patrick.delaunay at st.com
Wed Feb 27 14:36:44 UTC 2019


This patch update the behavior introduced by
commit 96907c0fe50a ("dm: spi: Read default speed and mode values from DT")

In case of DT boot, don't read default speed and mode for SPI from
CONFIG_* but instead read from DT node. This will make sure that boards
with multiple SPI/QSPI controllers can be probed at different
bus frequencies and SPI modes.

Remove also use in boards of the value speed=0 (no more supported)
for ENV in SPI by using CONFIG_ENV_SPI_MAX_HZ=0.

DT values will be always used when available (full DM support of
SPI slave with available DT node) even if speed and mode are requested;
for example in splash screen support (in splash_sf_read_raw)
or in SPL boot (in spl_spi_load_image).
The caller of spi_get_bus_and_cs() no more need to force speed=0.

But the current behavior don't change if the SPI slave is not
present (device with generic driver is created automatically)
or if platdata is used (CONFIG_OF_PLATDATA).

Signed-off-by: Patrick Delaunay <patrick.delaunay at st.com>
---

Changes in v4:
    - rebase on v2019.04-rc2
    - after Jagan review depends on Migrate SPI defines to Kconfig
      http://patchwork.ozlabs.org/project/uboot/list/?series=94485
    - remove no more supported configuration:
      CONFIG_ENV_SPI_MAX_HZ=0 or CONFIG_ENV_SPI_MODE=0

Changes in v3:
    - complete rework of the patch-set to avoid regression

Changes in v2:
    - use variables to avoid duplicated code

 cmd/sf.c                          | 3 +--
 common/spl/spl_spi.c              | 2 ++
 configs/da850_am18xxevm_defconfig | 4 ----
 configs/da850evm_defconfig        | 4 ----
 configs/mscc_jr2_defconfig        | 4 ----
 configs/mscc_luton_defconfig      | 4 ----
 configs/mscc_ocelot_defconfig     | 4 ----
 configs/mscc_serval_defconfig     | 4 ----
 configs/mscc_servalt_defconfig    | 4 ----
 drivers/mtd/spi/Kconfig           | 6 ++++++
 drivers/spi/spi-uclass.c          | 4 +++-
 include/spi.h                     | 9 +++++----
 12 files changed, 17 insertions(+), 35 deletions(-)

diff --git a/cmd/sf.c b/cmd/sf.c
index 738ef0e..6ccf98a 100644
--- a/cmd/sf.c
+++ b/cmd/sf.c
@@ -81,14 +81,13 @@ static int do_spi_flash_probe(int argc, char * const argv[])
 {
 	unsigned int bus = CONFIG_SF_DEFAULT_BUS;
 	unsigned int cs = CONFIG_SF_DEFAULT_CS;
+	/* In DM mode, defaults speed and mode will be taken from DT */
 	unsigned int speed = CONFIG_SF_DEFAULT_SPEED;
 	unsigned int mode = CONFIG_SF_DEFAULT_MODE;
 	char *endp;
 #ifdef CONFIG_DM_SPI_FLASH
 	struct udevice *new, *bus_dev;
 	int ret;
-	/* In DM mode defaults will be taken from DT */
-	speed = 0, mode = 0;
 #else
 	struct spi_flash *new;
 #endif
diff --git a/common/spl/spl_spi.c b/common/spl/spl_spi.c
index 8cd4830..9b74473 100644
--- a/common/spl/spl_spi.c
+++ b/common/spl/spl_spi.c
@@ -77,6 +77,8 @@ static int spl_spi_load_image(struct spl_image_info *spl_image,
 
 	/*
 	 * Load U-Boot image from SPI flash into RAM
+	 * In DM mode: defaults speed and mode will be
+	 * taken from DT when available
 	 */
 
 	flash = spi_flash_probe(CONFIG_SF_DEFAULT_BUS,
diff --git a/configs/da850_am18xxevm_defconfig b/configs/da850_am18xxevm_defconfig
index b1cf9bd..58745fe 100644
--- a/configs/da850_am18xxevm_defconfig
+++ b/configs/da850_am18xxevm_defconfig
@@ -38,10 +38,6 @@ CONFIG_SPL_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="da850-evm"
 CONFIG_SPL_OF_PLATDATA=y
 CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_USE_ENV_SPI_MAX_HZ=y
-CONFIG_ENV_SPI_MAX_HZ=0
-CONFIG_USE_ENV_SPI_MODE=y
-CONFIG_ENV_SPI_MODE=0
 CONFIG_DM=y
 CONFIG_SPL_DM=y
 CONFIG_DA8XX_GPIO=y
diff --git a/configs/da850evm_defconfig b/configs/da850evm_defconfig
index e6031b4..5100ee7 100644
--- a/configs/da850evm_defconfig
+++ b/configs/da850evm_defconfig
@@ -40,10 +40,6 @@ CONFIG_SPL_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="da850-evm"
 CONFIG_SPL_OF_PLATDATA=y
 CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_USE_ENV_SPI_MAX_HZ=y
-CONFIG_ENV_SPI_MAX_HZ=0
-CONFIG_USE_ENV_SPI_MODE=y
-CONFIG_ENV_SPI_MODE=0
 CONFIG_DM=y
 CONFIG_SPL_DM=y
 CONFIG_DM_GPIO=y
diff --git a/configs/mscc_jr2_defconfig b/configs/mscc_jr2_defconfig
index 95562b7..9276df2 100644
--- a/configs/mscc_jr2_defconfig
+++ b/configs/mscc_jr2_defconfig
@@ -38,10 +38,6 @@ CONFIG_OF_LIST="jr2_pcb110 jr2_pcb111 serval2_pcb112"
 CONFIG_DTB_RESELECT=y
 CONFIG_MULTI_DTB_FIT=y
 CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_USE_ENV_SPI_MAX_HZ=y
-CONFIG_ENV_SPI_MAX_HZ=0
-CONFIG_USE_ENV_SPI_MODE=y
-CONFIG_ENV_SPI_MODE=0
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_CLK=y
 CONFIG_DM_GPIO=y
diff --git a/configs/mscc_luton_defconfig b/configs/mscc_luton_defconfig
index 162a514..0fdd9b8 100644
--- a/configs/mscc_luton_defconfig
+++ b/configs/mscc_luton_defconfig
@@ -44,10 +44,6 @@ CONFIG_OF_LIST="luton_pcb090 luton_pcb091"
 CONFIG_DTB_RESELECT=y
 CONFIG_MULTI_DTB_FIT=y
 CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_USE_ENV_SPI_MAX_HZ=y
-CONFIG_ENV_SPI_MAX_HZ=0
-CONFIG_USE_ENV_SPI_MODE=y
-CONFIG_ENV_SPI_MODE=0
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_CLK=y
 CONFIG_DM_GPIO=y
diff --git a/configs/mscc_ocelot_defconfig b/configs/mscc_ocelot_defconfig
index b0dcfaf..edc476d 100644
--- a/configs/mscc_ocelot_defconfig
+++ b/configs/mscc_ocelot_defconfig
@@ -43,10 +43,6 @@ CONFIG_OF_LIST="ocelot_pcb120 ocelot_pcb123"
 CONFIG_DTB_RESELECT=y
 CONFIG_MULTI_DTB_FIT=y
 CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_USE_ENV_SPI_MAX_HZ=y
-CONFIG_ENV_SPI_MAX_HZ=0
-CONFIG_USE_ENV_SPI_MODE=y
-CONFIG_ENV_SPI_MODE=0
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_CLK=y
 CONFIG_DM_GPIO=y
diff --git a/configs/mscc_serval_defconfig b/configs/mscc_serval_defconfig
index f2c9563..146188b 100644
--- a/configs/mscc_serval_defconfig
+++ b/configs/mscc_serval_defconfig
@@ -35,10 +35,6 @@ CONFIG_OF_LIST="serval_pcb106 serval_pcb105"
 CONFIG_DTB_RESELECT=y
 CONFIG_MULTI_DTB_FIT=y
 CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_USE_ENV_SPI_MAX_HZ=y
-CONFIG_ENV_SPI_MAX_HZ=0
-CONFIG_USE_ENV_SPI_MODE=y
-CONFIG_ENV_SPI_MODE=0
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_CLK=y
 CONFIG_DM_GPIO=y
diff --git a/configs/mscc_servalt_defconfig b/configs/mscc_servalt_defconfig
index 027aaa4..a450f48 100644
--- a/configs/mscc_servalt_defconfig
+++ b/configs/mscc_servalt_defconfig
@@ -33,10 +33,6 @@ CONFIG_DEFAULT_DEVICE_TREE="servalt_pcb116"
 CONFIG_DTB_RESELECT=y
 CONFIG_MULTI_DTB_FIT=y
 CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_USE_ENV_SPI_MAX_HZ=y
-CONFIG_ENV_SPI_MAX_HZ=0
-CONFIG_USE_ENV_SPI_MODE=y
-CONFIG_ENV_SPI_MODE=0
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_CLK=y
 CONFIG_DM_GPIO=y
diff --git a/drivers/mtd/spi/Kconfig b/drivers/mtd/spi/Kconfig
index 5671bca..d3b007a 100644
--- a/drivers/mtd/spi/Kconfig
+++ b/drivers/mtd/spi/Kconfig
@@ -62,6 +62,9 @@ config SF_DEFAULT_MODE
 	  The default mode may be provided by the platform
 	  to handle the common case when only a single serial
 	  flash is present on the system.
+	  Not used for boot with device tree; the SPI driver reads
+	  speed and mode from platdata values computed from
+	  available node.
 
 config SF_DEFAULT_SPEED
 	int "SPI Flash default speed in Hz"
@@ -71,6 +74,9 @@ config SF_DEFAULT_SPEED
 	  The default speed may be provided by the platform
 	  to handle the common case when only a single serial
 	  flash is present on the system.
+	  Not used for boot with device tree; the SPI driver reads
+	  speed and mode from platdata values computed from
+	  available node.
 
 if SPI_FLASH
 
diff --git a/drivers/spi/spi-uclass.c b/drivers/spi/spi-uclass.c
index 2bc289a..88cb2a1 100644
--- a/drivers/spi/spi-uclass.c
+++ b/drivers/spi/spi-uclass.c
@@ -328,7 +328,9 @@ int spi_get_bus_and_cs(int busnum, int cs, int speed, int mode,
 	}
 
 	plat = dev_get_parent_platdata(dev);
-	if (!speed) {
+
+	/* get speed and mode from platdata when available */
+	if (plat->max_hz) {
 		speed = plat->max_hz;
 		mode = plat->mode;
 	}
diff --git a/include/spi.h b/include/spi.h
index 92427e5..3785941 100644
--- a/include/spi.h
+++ b/include/spi.h
@@ -496,14 +496,15 @@ int spi_find_bus_and_cs(int busnum, int cs, struct udevice **busp,
  * device and slave device.
  *
  * If no such slave exists, and drv_name is not NULL, then a new slave device
- * is automatically bound on this chip select.
+ * is automatically bound on this chip select with requested speed and mode.
  *
- * Ths new slave device is probed ready for use with the given speed and mode.
+ * Ths new slave device is probed ready for use with the speed and mode
+ * from platdata when available or the requested values.
  *
  * @busnum:	SPI bus number
  * @cs:		Chip select to look for
- * @speed:	SPI speed to use for this slave
- * @mode:	SPI mode to use for this slave
+ * @speed:	SPI speed to use for this slave when not available in platdata
+ * @mode:	SPI mode to use for this slave when not available in platdata
  * @drv_name:	Name of driver to attach to this chip select
  * @dev_name:	Name of the new device thus created
  * @busp:	Returns bus device
-- 
2.7.4



More information about the U-Boot mailing list