[U-Boot] [PATCH 08/19] stm32mp1: update bootcmd

Patrick Delaunay patrick.delaunay at st.com
Wed Feb 27 16:01:18 UTC 2019


Clearly separate bootcmd for stm32mp1 board
(bootcmd_stm32mp) and preboot management.
That solve issue for fastboot continue command.

Signed-off-by: Patrick Delaunay <patrick.delaunay at st.com>
---

 board/st/stm32mp1/stm32mp1.c        |  1 +
 configs/stm32mp15_basic_defconfig   |  1 +
 configs/stm32mp15_trusted_defconfig |  1 +
 include/configs/stm32mp1.h          | 37 +++++++++++++++++++++++++++----------
 4 files changed, 30 insertions(+), 10 deletions(-)

diff --git a/board/st/stm32mp1/stm32mp1.c b/board/st/stm32mp1/stm32mp1.c
index 48da459..0d963c2 100644
--- a/board/st/stm32mp1/stm32mp1.c
+++ b/board/st/stm32mp1/stm32mp1.c
@@ -14,6 +14,7 @@
 #include <usb.h>
 #include <asm/arch/stm32.h>
 #include <asm/io.h>
+#include <asm/gpio.h>
 #include <power/regulator.h>
 #include <usb/dwc2_udc.h>
 
diff --git a/configs/stm32mp15_basic_defconfig b/configs/stm32mp15_basic_defconfig
index b1d09fb..4ab29ee 100644
--- a/configs/stm32mp15_basic_defconfig
+++ b/configs/stm32mp15_basic_defconfig
@@ -5,6 +5,7 @@ CONFIG_SPL_MMC_SUPPORT=y
 CONFIG_SPL=y
 CONFIG_TARGET_STM32MP1=y
 CONFIG_DISTRO_DEFAULTS=y
+CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3
 CONFIG_SPL_I2C_SUPPORT=y
diff --git a/configs/stm32mp15_trusted_defconfig b/configs/stm32mp15_trusted_defconfig
index 9be7319..1bb3d0d 100644
--- a/configs/stm32mp15_trusted_defconfig
+++ b/configs/stm32mp15_trusted_defconfig
@@ -3,6 +3,7 @@ CONFIG_ARCH_STM32MP=y
 CONFIG_SYS_MALLOC_F_LEN=0x2000
 CONFIG_TARGET_STM32MP1=y
 CONFIG_DISTRO_DEFAULTS=y
+CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
 CONFIG_SYS_PROMPT="STM32MP> "
 # CONFIG_CMD_BOOTD is not set
 # CONFIG_CMD_ELF is not set
diff --git a/include/configs/stm32mp1.h b/include/configs/stm32mp1.h
index 4722672..48da1e3 100644
--- a/include/configs/stm32mp1.h
+++ b/include/configs/stm32mp1.h
@@ -10,8 +10,6 @@
 #include <linux/sizes.h>
 #include <asm/arch/stm32.h>
 
-#define CONFIG_PREBOOT
-
 /*
  * Number of clock ticks in 1 sec
  */
@@ -75,20 +73,38 @@
 #define CONFIG_SYS_MMC_MAX_DEVICE	3
 #define CONFIG_SUPPORT_EMMC_BOOT
 
-#if !defined(CONFIG_SPL) || !defined(CONFIG_SPL_BUILD)
+/*****************************************************************************/
+#ifdef CONFIG_DISTRO_DEFAULTS
+/*****************************************************************************/
+
+#if !defined(CONFIG_SPL_BUILD)
 
 #define BOOT_TARGET_DEVICES(func) \
 	func(MMC, mmc, 1) \
 	func(MMC, mmc, 0) \
 	func(MMC, mmc, 2)
+/*
+ * bootcmd for stm32mp1:
+ * for serial/usb: execute the stm32prog command
+ * for mmc boot (eMMC, SD card), boot only on the same device
+ * for nand boot, boot with on ubifs partition on nand
+ * for nor boot, use the default order
+ */
+#define CONFIG_PREBOOT
 
-#include <config_distro_bootcmd.h>
+#define STM32MP_BOOTCMD "bootcmd_stm32mp=" \
+	"echo \"Boot over ${boot_device}${boot_instance}!\";" \
+	"if test ${boot_device} = serial || test ${boot_device} = usb;" \
+	"then stm32prog ${boot_device} ${boot_instance}; " \
+	"else " \
+		"if test ${boot_device} = mmc;" \
+		"then env set boot_targets \"mmc${boot_instance}\"; fi;" \
+		"if test ${boot_device} = nand;" \
+		"then env set boot_targets ubifs0; fi;" \
+		"run distro_bootcmd;" \
+	"fi;\0"
 
-#define STM32MP_PREBOOT	\
-	"echo \"Boot over ${boot_device}${boot_instance}!\"; " \
-	"if test \"${boot_device}\" = \"mmc\"; then " \
-		"env set boot_targets \"mmc${boot_instance}\"; "\
-	"fi;"
+#include <config_distro_bootcmd.h>
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"scriptaddr=0xC0000000\0" \
@@ -98,9 +114,10 @@
 	"ramdisk_addr_r=0xC4100000\0" \
 	"fdt_high=0xffffffff\0" \
 	"initrd_high=0xffffffff\0" \
-	"preboot=" STM32MP_PREBOOT "\0" \
+	STM32MP_BOOTCMD \
 	BOOTENV
 
 #endif /* ifndef CONFIG_SPL_BUILD */
+#endif /* ifdef CONFIG_DISTRO_DEFAULTS*/
 
 #endif /* __CONFIG_H */
-- 
2.7.4



More information about the U-Boot mailing list