[U-Boot] [RESEND PATCH v2 15/15] arm: socfpga: agilex: Enable Agilex SoC build
Ley Foon Tan
ley.foon.tan at intel.com
Thu Jul 4 08:56:12 UTC 2019
Add build support for Agilex SoC.
Signed-off-by: Ley Foon Tan <ley.foon.tan at intel.com>
---
v2:
- Remove IC_CLK define, use clock DM method to get i2c clock
- Change CONFIG_ENV_SIZE to 4KB since CONFIG_SPI_FLASH_USE_4K_SECTORS is enabled.
---
arch/arm/Kconfig | 4 +-
arch/arm/mach-socfpga/Kconfig | 15 ++
arch/arm/mach-socfpga/Makefile | 9 ++
configs/socfpga_agilex_defconfig | 57 +++++++
include/configs/socfpga_agilex_socdk.h | 208 +++++++++++++++++++++++++
5 files changed, 291 insertions(+), 2 deletions(-)
create mode 100644 configs/socfpga_agilex_defconfig
create mode 100644 include/configs/socfpga_agilex_socdk.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 01ff57cf1b..213c37cd7e 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -870,7 +870,7 @@ config ARCH_SOCFPGA
bool "Altera SOCFPGA family"
select ARCH_EARLY_INIT_R
select ARCH_MISC_INIT if !TARGET_SOCFPGA_ARRIA10
- select ARM64 if TARGET_SOCFPGA_STRATIX10
+ select ARM64 if TARGET_SOCFPGA_STRATIX10 || TARGET_SOCFPGA_AGILEX
select CPU_V7A if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
select DM
select DM_SERIAL
@@ -882,7 +882,7 @@ config ARCH_SOCFPGA
select SPL_LIBGENERIC_SUPPORT
select SPL_NAND_SUPPORT if SPL_NAND_DENALI
select SPL_OF_CONTROL
- select SPL_SEPARATE_BSS if TARGET_SOCFPGA_STRATIX10
+ select SPL_SEPARATE_BSS if TARGET_SOCFPGA_STRATIX10 || TARGET_SOCFPGA_AGILEX
select SPL_SERIAL_SUPPORT
select SPL_WATCHDOG_SUPPORT
select SUPPORT_SPL
diff --git a/arch/arm/mach-socfpga/Kconfig b/arch/arm/mach-socfpga/Kconfig
index 48f02f08d4..b850a8ab1f 100644
--- a/arch/arm/mach-socfpga/Kconfig
+++ b/arch/arm/mach-socfpga/Kconfig
@@ -20,6 +20,14 @@ config SYS_TEXT_BASE
default 0x01000040 if TARGET_SOCFPGA_ARRIA10
default 0x01000040 if TARGET_SOCFPGA_GEN5
+config TARGET_SOCFPGA_AGILEX
+ bool
+ select ARMV8_MULTIENTRY
+ select ARMV8_SET_SMPEN
+ select ARMV8_SPIN_TABLE
+ select CLK
+ select SPL_CLK if SPL
+
config TARGET_SOCFPGA_ARRIA5
bool
select TARGET_SOCFPGA_GEN5
@@ -64,6 +72,10 @@ choice
prompt "Altera SOCFPGA board select"
optional
+config TARGET_SOCFPGA_AGILEX_SOCDK
+ bool "Intel SOCFPGA SoCDK (Agilex)"
+ select TARGET_SOCFPGA_AGILEX
+
config TARGET_SOCFPGA_ARIES_MCVEVK
bool "Aries MCVEVK (Cyclone V)"
select TARGET_SOCFPGA_CYCLONE5
@@ -124,6 +136,7 @@ config TARGET_SOCFPGA_TERASIC_SOCKIT
endchoice
config SYS_BOARD
+ default "agilex-socdk" if TARGET_SOCFPGA_AGILEX_SOCDK
default "arria5-socdk" if TARGET_SOCFPGA_ARRIA5_SOCDK
default "arria10-socdk" if TARGET_SOCFPGA_ARRIA10_SOCDK
default "cyclone5-socdk" if TARGET_SOCFPGA_CYCLONE5_SOCDK
@@ -140,6 +153,7 @@ config SYS_BOARD
default "vining_fpga" if TARGET_SOCFPGA_SAMTEC_VINING_FPGA
config SYS_VENDOR
+ default "intel" if TARGET_SOCFPGA_AGILEX_SOCDK
default "altera" if TARGET_SOCFPGA_ARRIA5_SOCDK
default "altera" if TARGET_SOCFPGA_ARRIA10_SOCDK
default "altera" if TARGET_SOCFPGA_CYCLONE5_SOCDK
@@ -157,6 +171,7 @@ config SYS_SOC
default "socfpga"
config SYS_CONFIG_NAME
+ default "socfpga_agilex_socdk" if TARGET_SOCFPGA_AGILEX_SOCDK
default "socfpga_arria5_socdk" if TARGET_SOCFPGA_ARRIA5_SOCDK
default "socfpga_arria10_socdk" if TARGET_SOCFPGA_ARRIA10_SOCDK
default "socfpga_cyclone5_socdk" if TARGET_SOCFPGA_CYCLONE5_SOCDK
diff --git a/arch/arm/mach-socfpga/Makefile b/arch/arm/mach-socfpga/Makefile
index 476dcaefff..774d3571ef 100644
--- a/arch/arm/mach-socfpga/Makefile
+++ b/arch/arm/mach-socfpga/Makefile
@@ -42,6 +42,14 @@ endif
ifdef CONFIG_TARGET_SOCFPGA_AGILEX
obj-y += clock_manager_agilex.o
+obj-y += mailbox_s10.o
+obj-y += misc_s10.o
+obj-y += mmu-arm64_s10.o
+obj-y += reset_manager_s10.o
+obj-y += system_manager_s10.o
+obj-y += timer_s10.o
+obj-y += wrap_pinmux_config_s10.o
+obj-y += wrap_pll_config_s10.o
endif
ifdef CONFIG_SPL_BUILD
@@ -61,6 +69,7 @@ obj-y += spl_s10.o
endif
ifdef CONFIG_TARGET_SOCFPGA_AGILEX
obj-y += ccu_agilex.o
+obj-y += firewall.o
obj-y += spl_agilex.o
endif
endif
diff --git a/configs/socfpga_agilex_defconfig b/configs/socfpga_agilex_defconfig
new file mode 100644
index 0000000000..bb09a80db2
--- /dev/null
+++ b/configs/socfpga_agilex_defconfig
@@ -0,0 +1,57 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SOCFPGA=y
+CONFIG_SYS_TEXT_BASE=0x1000
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_TARGET_SOCFPGA_AGILEX_SOCDK=y
+CONFIG_IDENT_STRING="socfpga_agilex"
+CONFIG_SPL_FS_FAT=y
+CONFIG_BOOTDELAY=5
+CONFIG_SPL_TEXT_BASE=0xFFE00000
+CONFIG_SPL_SPI_LOAD=y
+CONFIG_HUSH_PARSER=y
+CONFIG_SYS_PROMPT="SOCFPGA_AGILEX # "
+CONFIG_CMD_MEMTEST=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_OF_EMBED=y
+CONFIG_DEFAULT_DEVICE_TREE="socfpga_agilex_socdk"
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SPL_ALTERA_SDRAM=y
+CONFIG_DM_GPIO=y
+CONFIG_DWAPB_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_DW=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_DW=y
+CONFIG_SPI_FLASH=y
+CONFIG_SF_DEFAULT_MODE=0x2003
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_PHY_MICREL=y
+CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_MII=y
+CONFIG_DM_RESET=y
+CONFIG_SPI=y
+CONFIG_CADENCE_QSPI=y
+CONFIG_DESIGNWARE_SPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_DWC2=y
+CONFIG_USB_STORAGE=y
diff --git a/include/configs/socfpga_agilex_socdk.h b/include/configs/socfpga_agilex_socdk.h
new file mode 100644
index 0000000000..add02aa5ab
--- /dev/null
+++ b/include/configs/socfpga_agilex_socdk.h
@@ -0,0 +1,208 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * Copyright (C) 2019 Intel Corporation <www.intel.com>
+ *
+ */
+
+#ifndef __CONFIG_SOCFGPA_AGILEX_H__
+#define __CONFIG_SOCFGPA_AGILEX_H__
+
+#include <asm/arch/base_addr_s10.h>
+#include <asm/arch/handoff_s10.h>
+
+/*
+ * U-Boot general configurations
+ */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_LOADADDR 0x2000000
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+#define CONFIG_REMAKE_ELF
+/* sysmgr.boot_scratch_cold4 & 5 (64bit) will be used for PSCI_CPU_ON call */
+#define CPU_RELEASE_ADDR 0xFFD12210
+#define CONFIG_SYS_CACHELINE_SIZE 64
+#define CONFIG_SYS_MEM_RESERVE_SECURE 0 /* using OCRAM, not DDR */
+
+/*
+ * U-Boot console configurations
+ */
+#define CONFIG_SYS_MAXARGS 64
+#define CONFIG_SYS_CBSIZE 2048
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+/* Extend size of kernel image for uncompression */
+#define CONFIG_SYS_BOOTM_LEN (32 * 1024 * 1024)
+
+/*
+ * U-Boot run time memory configurations
+ */
+#define CONFIG_SYS_INIT_RAM_ADDR 0xFFE00000
+#define CONFIG_SYS_INIT_RAM_SIZE 0x40000
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR \
+ + CONFIG_SYS_INIT_RAM_SIZE \
+ - S10_HANDOFF_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_SP_ADDR)
+#define CONFIG_SYS_MALLOC_LEN (5 * 1024 * 1024)
+
+/*
+ * U-Boot environment configurations
+ */
+#define CONFIG_ENV_SIZE 0x1000
+#define CONFIG_SYS_MMC_ENV_DEV 0 /* device 0 */
+#define CONFIG_ENV_OFFSET 512 /* just after the MBR */
+
+/*
+ * QSPI support
+ */
+ #ifdef CONFIG_CADENCE_QSPI
+/* Enable it if you want to use dual-stacked mode */
+/*#define CONFIG_QSPI_RBF_ADDR 0x720000*/
+
+/* Flash device info */
+
+/*#define CONFIG_ENV_IS_IN_SPI_FLASH*/
+#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
+#undef CONFIG_ENV_OFFSET
+#undef CONFIG_ENV_SIZE
+#define CONFIG_ENV_OFFSET 0x710000
+#define CONFIG_ENV_SIZE (4 * 1024)
+#define CONFIG_ENV_SECT_SIZE (4 * 1024)
+#endif /* CONFIG_ENV_IS_IN_SPI_FLASH */
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define MTDIDS_DEFAULT "nor0=ff705000.spi.0"
+#endif /* CONFIG_SPL_BUILD */
+
+#ifndef __ASSEMBLY__
+unsigned int cm_get_qspi_controller_clk_hz(void);
+#define CONFIG_CQSPI_REF_CLK cm_get_qspi_controller_clk_hz()
+#endif
+
+#endif /* CONFIG_CADENCE_QSPI */
+
+/*
+ * Boot arguments passed to the boot command. The value of
+ * CONFIG_BOOTARGS goes into the environment value "bootargs".
+ * Do note the value will override also the chosen node in FDT blob.
+ */
+#define CONFIG_BOOTARGS "earlycon"
+#define CONFIG_BOOTCOMMAND "run fatscript; run mmcload;run linux_qspi_enable;" \
+ "run mmcboot"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "loadaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
+ "bootfile=Image\0" \
+ "fdt_addr=8000000\0" \
+ "fdtimage=socfpga_agilex_socdk.dtb\0" \
+ "mmcroot=/dev/mmcblk0p2\0" \
+ "mmcboot=setenv bootargs " CONFIG_BOOTARGS \
+ " root=${mmcroot} rw rootwait;" \
+ "booti ${loadaddr} - ${fdt_addr}\0" \
+ "mmcload=mmc rescan;" \
+ "load mmc 0:1 ${loadaddr} ${bootfile};" \
+ "load mmc 0:1 ${fdt_addr} ${fdtimage}\0" \
+ "linux_qspi_enable=if sf probe; then " \
+ "echo Enabling QSPI at Linux DTB...;" \
+ "fdt addr ${fdt_addr}; fdt resize;" \
+ "fdt set /soc/spi at ff8d2000 status okay;" \
+ "fdt set /soc/clkmgr/clocks/qspi_clk clock-frequency " \
+ " ${qspi_clock}; fi; \0" \
+ "scriptaddr=0x02100000\0" \
+ "scriptfile=u-boot.scr\0" \
+ "fatscript=if fatload mmc 0:1 ${scriptaddr} ${scriptfile};" \
+ "then source ${scriptaddr}; fi\0"
+
+/*
+ * Generic Interrupt Controller Definitions
+ */
+#define CONFIG_GICV2
+
+/*
+ * External memory configurations
+ */
+#define PHYS_SDRAM_1 0x0
+#define PHYS_SDRAM_1_SIZE (1 * 1024 * 1024 * 1024)
+#define CONFIG_SYS_SDRAM_BASE 0
+#define CONFIG_SYS_MEMTEST_START 0
+#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1_SIZE - 0x200000
+
+/*
+ * Serial / UART configurations
+ */
+#define CONFIG_SYS_NS16550_CLK 100000000
+#define CONFIG_SYS_NS16550_MEM32
+
+/*
+ * Timer & watchdog configurations
+ */
+#define COUNTER_FREQUENCY 400000000
+
+/*
+ * SDMMC configurations
+ */
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_SYS_MMC_MAX_BLK_COUNT 256
+#endif
+/*
+ * Flash configurations
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+
+/* Ethernet on SoC (EMAC) */
+#if defined(CONFIG_CMD_NET)
+#define CONFIG_DW_ALTDESCRIPTOR
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * L4 Watchdog
+ */
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_DESIGNWARE_WATCHDOG
+#define CONFIG_DW_WDT_BASE SOCFPGA_L4WD0_ADDRESS
+#ifndef __ASSEMBLY__
+#define CONFIG_DW_WDT_CLOCK_KHZ 100000
+#endif
+#define CONFIG_WATCHDOG_TIMEOUT_MSECS 3000
+#endif
+
+/*
+ * SPL memory layout
+ *
+ * On chip RAM
+ * 0xFFE0_0000 ...... Start of OCRAM
+ * SPL code, rwdata
+ * empty space
+ * 0xFFEx_xxxx ...... Top of stack (grows down)
+ * 0xFFEy_yyyy ...... Global Data
+ * 0xFFEz_zzzz ...... Malloc prior relocation (size CONFIG_SYS_MALLOC_F_LEN)
+ * 0xFFE3_F000 ...... Hardware handdoff blob (size 4KB)
+ * 0xFFE3_FFFF ...... End of OCRAM
+ *
+ * SDRAM
+ * 0x0000_0000 ...... Start of SDRAM_1
+ * unused / empty space for image loading
+ * Size 64MB ...... MALLOC (size CONFIG_SYS_SPL_MALLOC_SIZE)
+ * Size 1MB ...... BSS (size CONFIG_SPL_BSS_MAX_SIZE)
+ * 0x8000_0000 ...... End of SDRAM_1 (assume 2GB)
+ *
+ */
+#define CONFIG_SPL_TARGET "spl/u-boot-spl.hex"
+#define CONFIG_SPL_MAX_SIZE CONFIG_SYS_INIT_RAM_SIZE
+#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
+#define CONFIG_SPL_BSS_MAX_SIZE 0x100000 /* 1 MB */
+#define CONFIG_SPL_BSS_START_ADDR (PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE \
+ - CONFIG_SPL_BSS_MAX_SIZE)
+#define CONFIG_SYS_SPL_MALLOC_SIZE (CONFIG_SYS_MALLOC_LEN)
+#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR \
+ - CONFIG_SYS_SPL_MALLOC_SIZE)
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x3C00000
+
+/* SPL SDMMC boot support */
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
+
+#endif /* __CONFIG_H */
--
2.19.0
More information about the U-Boot
mailing list