[U-Boot] [PATCH 00/52] Support i.MX8MM/N
Peng Fan
peng.fan at nxp.com
Mon Jul 8 01:28:13 UTC 2019
> Subject: Re: [U-Boot] [PATCH 00/52] Support i.MX8MM/N
>
> Hi Peng,
>
> > From: Peng Fan <peng.fan at nxp.com>
> >
> > This patchset is to support i.MX8MM/8MN with some update in ddr
> > settings and ddr driver update.
> >
> > The initial patchset to support i.MX8MM is
> > https://patchwork.ozlabs.org/cover/1093140/
> > But in this patchset I dropped CCF, and use original CLK uclass, so
> > not use V2 in patchset.
>
> I'm a bit confused here regarding the CCF adoption.
>
> From this patch set I do see that in one place you enable CONFIG_CLK_CCF
> and CONFIG_SPL_CLK_CCF and then it is removed in the other patch.
> For example the patch 48/52 extends the drivers/clk/imx/clk-imx8mm.c,
> which looks like the old approach for the clocking.
The v2 patchset has cleanup https://github.com/MrVan/u-boot/tree/8m-7-5
>
> Am I correct that the v2 of this patch set will use the CCF v5, which I've sent
> some time ago (CCF v4 was used on some i.MX8 SoC though)?
No. I tried CCF on i.MX8MM in previous patchset, but I dropped it for now.
We might try to switch to CCF again in future, but we hope i.MX8MM/N
support could land in upstream soon. It has been pending for months.
Regards,
Peng.
>
> >
> > Bai Ping (1):
> > imx8mq: Update the ddrc QoS setting for B1 chip
> >
> > Jacky Bai (2):
> > driver: ddr: Refine the ddr init driver on imx8m
> > ddr: imx8m: Fix the ddr init hang on imx8mq
> >
> > Peng Fan (47):
> > linux: compat: guard PAGE_SIZE
> > dm: clk: ignore default settings when node not valid
> > pinctrl: imx: use devfdt_get_addr_size_index
> > i2c: mxc: add CONFIG_CLK support
> > tools: imx8m_image: align spl bin image size
> > ddr: imx8m: fix ddr firmware location when enable SPL OF
> > tools: imx8mimage: fix HDMI/FIT parsing
> > imx8m: add image cfg for i.MX8MM lpddr4
> > imx: add IMX8MQ kconfig entry
> > imx: add IMX8MM kconfig entry
> > imx: imx8mm: add clock bindings header
> > imx: add i.MX8MM cpu type
> > imx: spl: add spl_board_boot_device for i.MX8MM
> > imx8m: update imx-regs for i.MX8MM
> > imx: add get_cpu_rev support for i.MX8MM
> > imx8m: rename clock to clock_imx8mq
> > imx8m: restructure clock.h
> > imx8m: add clk support for i.MX8MM
> > imx8m: soc: probe clk before relocation
> > imx8m: add pin header for i.MX8MM
> > imx: add i.MX8MM PE property
> > imx8m: Fix MMU table issue for OPTEE memory
> > imx8m: set BYPASS ID SWAP to avoid AXI bus errors
> > imx8m: soc: enable SCTR clock before timer init
> > serial: Kconfig: make MXC_UART usable for MX7 and IMX8M
> > clk: imx: add Kconfig entry for i.MX8MM
> > clk: imx: add i.MX8MM clk driver
> > imx: add i.MX8MM EVK board support
> > imx: add i.MX8MN kconfig entry
> > imx8mn: support get_cpu_rev
> > imx8m: add clk support for i.MX8MN
> > imx8mn: set BYPASS ID SWAP to avoid AXI bus errors
> > imx: add i.MX8MN PE property
> > imx8mn: add pin header
> > imx: spl: use spl_board_boot_device for i.MX8MN
> > spl: pass args to board_return_to_bootrom
> > imx: add rom api support
> > imx: cpu: restrict get_boot_device
> > imx8mn: add get_boot_device
> > power: pmic: add SPL_DM_PMIC
> > tools: imx8mimage: add ROM VERSION
> > pinctrl: imx8m: support i.MX8MN
> > tools: imx8m_image: support ddr4 firmware
> > clk: imx: add i.MX8MN clk support
> > imx8m: add i.MX8MN ddr4 image cfg file
> > imx: add dtsi for i.MX8MN
> > imx: add i.MX8MN DDR4 board support
> >
> > Ye Li (2):
> > imx8m: Configure trustzone region 0 for non-secure access
> > ddr: imx8m: Fix ddr4 driver build issue
> >
> > arch/arm/dts/Makefile | 4 +-
> > arch/arm/dts/imx8mm-evk-u-boot.dtsi | 92 +
> > arch/arm/dts/imx8mm-evk.dts | 235 +++
> > arch/arm/dts/imx8mm-pinfunc.h | 629
> +++++++
> > arch/arm/dts/imx8mm.dtsi | 733
> ++++++++
> > arch/arm/dts/imx8mn-ddr4-evk-u-boot.dtsi | 92 +
> > arch/arm/dts/imx8mn-ddr4-evk.dts | 221 +++
> > arch/arm/dts/imx8mn-pinfunc.h | 646
> +++++++
> > arch/arm/dts/imx8mn.dtsi | 712
> +++++++
> > arch/arm/include/asm/arch-imx/cpu.h | 7 +
> > arch/arm/include/asm/arch-imx8m/clock.h | 494 +----
> > arch/arm/include/asm/arch-imx8m/clock_imx8mm.h | 465
> +++++
> > arch/arm/include/asm/arch-imx8m/clock_imx8mq.h | 424 +++++
> > arch/arm/include/asm/arch-imx8m/imx-regs.h | 75 +-
> > arch/arm/include/asm/arch-imx8m/imx8mm_pins.h | 691
> +++++++
> > arch/arm/include/asm/arch-imx8m/imx8mn_pins.h | 763
> ++++++++
> > arch/arm/include/asm/mach-imx/iomux-v3.h | 4 +
> > arch/arm/include/asm/mach-imx/mxc_i2c.h | 2 +
> > arch/arm/include/asm/mach-imx/sys_proto.h | 42 +
> > arch/arm/mach-imx/Kconfig | 4 +
> > arch/arm/mach-imx/Makefile | 2 +
> > arch/arm/mach-imx/cpu.c | 16 +-
> > arch/arm/mach-imx/imx8m/Kconfig | 28 +-
> > arch/arm/mach-imx/imx8m/Makefile | 4 +-
> > arch/arm/mach-imx/imx8m/clock_imx8mm.c | 707
> +++++++
> > .../arm/mach-imx/imx8m/{clock.c => clock_imx8mq.c} | 7 +-
> > arch/arm/mach-imx/imx8m/clock_slice.c | 815
> ++++++++
> > arch/arm/mach-imx/imx8m/imximage-8mm-lpddr4.cfg | 16 +
> > arch/arm/mach-imx/imx8m/imximage-8mn-ddr4.cfg | 17 +
> > arch/arm/mach-imx/imx8m/soc.c | 162 +-
> > arch/arm/mach-imx/spl.c | 8 +
> > arch/arm/mach-imx/spl_imx_romapi.c | 292 +++
> > arch/arm/mach-rockchip/rk3288-board-tpl.c | 5 +-
> > arch/arm/mach-rockchip/rk3368-board-tpl.c | 5 +-
> > arch/arm/mach-rockchip/rk3399-board-spl.c | 5 +-
> > arch/arm/mach-rockchip/rk3399-board-tpl.c | 5 +-
> > board/freescale/imx8mm_evk/Kconfig | 12 +
> > board/freescale/imx8mm_evk/MAINTAINERS | 6 +
> > board/freescale/imx8mm_evk/Makefile | 12 +
> > board/freescale/imx8mm_evk/imx8mm_evk.c | 90 +
> > board/freescale/imx8mm_evk/lpddr4_timing.c | 1980
> > ++++++++++++++++++++
> > board/freescale/imx8mm_evk/spl.c | 216 +++
> > board/freescale/imx8mn_evk/Kconfig | 14 +
> > board/freescale/imx8mn_evk/MAINTAINERS | 6 +
> > board/freescale/imx8mn_evk/Makefile | 12 +
> > board/freescale/imx8mn_evk/ddr4_timing.c | 1214
> > ++++++++++++ board/freescale/imx8mn_evk/imx8mn_evk.c
> |
> > 85 + board/freescale/imx8mn_evk/spl.c | 91 +
> > board/freescale/imx8mq_evk/lpddr4_timing.c | 16 +-
> > common/spl/spl_bootrom.c | 7 +-
> > configs/imx8mm_evk_defconfig | 51 +
> > configs/imx8mn_ddr4_evk_defconfig | 55 +
> > drivers/clk/clk-uclass.c | 3 +
> > drivers/clk/imx/Kconfig | 14 +
> > drivers/clk/imx/Makefile | 1 +
> > drivers/clk/imx/clk-imx8mm.c | 121 ++
> > drivers/ddr/imx/imx8m/Kconfig | 6 +
> > drivers/ddr/imx/imx8m/Makefile | 4 +-
> > drivers/ddr/imx/imx8m/ddr4_init.c | 113 --
> > drivers/ddr/imx/imx8m/ddr_init.c | 168 ++
> > drivers/ddr/imx/imx8m/ddrphy_utils.c | 4 +
> > drivers/ddr/imx/imx8m/helper.c | 22 +-
> > drivers/ddr/imx/imx8m/lpddr4_init.c | 188 --
> > drivers/i2c/mxc_i2c.c | 24 +-
> > drivers/pinctrl/nxp/pinctrl-imx.c | 4 +-
> > drivers/pinctrl/nxp/pinctrl-imx8m.c | 1 +
> > drivers/power/pmic/Kconfig | 12 +
> > drivers/power/pmic/Makefile | 2 +-
> > drivers/serial/Kconfig | 2 +-
> > include/configs/imx8mm_evk.h | 200 ++
> > include/configs/imx8mn_evk.h | 198 ++
> > include/dt-bindings/clock/imx8mm-clock.h | 244 +++
> > include/dt-bindings/clock/imx8mn-clock.h | 215 +++
> > include/imximage.h | 1 +
> > include/linux/compat.h | 2 +
> > include/power/pmic.h | 2 +-
> > include/spl.h | 3 +-
> > tools/imx8m_image.sh | 15 +-
> > tools/imx8mimage.c | 31 +- 79
> files
> > changed, 13082 insertions(+), 814 deletions(-) create mode 100644
> > arch/arm/dts/imx8mm-evk-u-boot.dtsi create mode 100644
> > arch/arm/dts/imx8mm-evk.dts create mode 100644
> > arch/arm/dts/imx8mm-pinfunc.h create mode 100644
> > arch/arm/dts/imx8mm.dtsi create mode 100644
> > arch/arm/dts/imx8mn-ddr4-evk-u-boot.dtsi create mode 100644
> > arch/arm/dts/imx8mn-ddr4-evk.dts create mode 100644
> > arch/arm/dts/imx8mn-pinfunc.h create mode 100644
> > arch/arm/dts/imx8mn.dtsi create mode 100644
> > arch/arm/include/asm/arch-imx8m/clock_imx8mm.h create mode 100644
> > arch/arm/include/asm/arch-imx8m/clock_imx8mq.h create mode 100644
> > arch/arm/include/asm/arch-imx8m/imx8mm_pins.h create mode 100644
> > arch/arm/include/asm/arch-imx8m/imx8mn_pins.h create mode 100644
> > arch/arm/mach-imx/imx8m/clock_imx8mm.c rename
> > arch/arm/mach-imx/imx8m/{clock.c => clock_imx8mq.c} (99%) create
> mode
> > 100644 arch/arm/mach-imx/imx8m/imximage-8mm-lpddr4.cfg create
> mode
> > 100644 arch/arm/mach-imx/imx8m/imximage-8mn-ddr4.cfg create mode
> > 100644 arch/arm/mach-imx/spl_imx_romapi.c create mode 100644
> > board/freescale/imx8mm_evk/Kconfig create mode 100644
> > board/freescale/imx8mm_evk/MAINTAINERS create mode 100644
> > board/freescale/imx8mm_evk/Makefile create mode 100644
> > board/freescale/imx8mm_evk/imx8mm_evk.c create mode 100644
> > board/freescale/imx8mm_evk/lpddr4_timing.c create mode 100644
> > board/freescale/imx8mm_evk/spl.c create mode 100644
> > board/freescale/imx8mn_evk/Kconfig create mode 100644
> > board/freescale/imx8mn_evk/MAINTAINERS create mode 100644
> > board/freescale/imx8mn_evk/Makefile create mode 100644
> > board/freescale/imx8mn_evk/ddr4_timing.c create mode 100644
> > board/freescale/imx8mn_evk/imx8mn_evk.c create mode 100644
> > board/freescale/imx8mn_evk/spl.c create mode 100644
> > configs/imx8mm_evk_defconfig create mode 100644
> > configs/imx8mn_ddr4_evk_defconfig create mode 100644
> > drivers/clk/imx/clk-imx8mm.c delete mode 100644
> > drivers/ddr/imx/imx8m/ddr4_init.c create mode 100644
> > drivers/ddr/imx/imx8m/ddr_init.c delete mode 100644
> > drivers/ddr/imx/imx8m/lpddr4_init.c create mode 100644
> > include/configs/imx8mm_evk.h create mode 100644
> > include/configs/imx8mn_evk.h create mode 100644
> > include/dt-bindings/clock/imx8mm-clock.h create mode 100644
> > include/dt-bindings/clock/imx8mn-clock.h
> >
>
>
>
>
> Best regards,
>
> Lukasz Majewski
>
> --
>
> DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email:
> lukma at denx.de
More information about the U-Boot
mailing list