[U-Boot] [PATCH 8/8] Add support for the NXP LS1021A-TSN board
Vladimir Oltean
olteanv at gmail.com
Mon Jul 15 21:56:28 UTC 2019
Hi Joe,
On Mon, 15 Jul 2019 at 22:17, Joe Hershberger <joe.hershberger at ni.com> wrote:
>
> On Sun, Jun 23, 2019 at 12:53 PM Vladimir Oltean <olteanv at gmail.com> wrote:
> >
> > From: Jianchao Wang <jianchao.wang at nxp.com>
> >
> > The LS1021A-TSN is a development board built by VVDN/Argonboards in
> > partnership with NXP.
> >
> > It features the LS1021A SoC and the first-generation SJA1105T Ethernet
> > switch for prototyping implementations of a subset of IEEE 802.1 TSN
> > standards.
> >
> > Supported boot media: microSD card (via SPL), QSPI flash.
> >
> > Rev. A of the board uses a Spansion S25FL512S_256K serial flash, which
> > is 64 MB in size and has an erase sector size of 256KB (therefore,
> > flashing the RCW would erase part of U-boot).
> >
> > Rev. B and C of the board use a Spansion S25FL256S1 serial flash, which
> > is only 32 MB in size but has an erase sector size of 64KB (therefore
> > the RCW image can be flashed without erasing U-boot).
> >
> > To avoid the problems above, the U-boot base address has been selected
> > at 0x100000 (the start of the 5th 256KB erase sector), which works for
> > all board revisions. Actually 0x40000 would have been enough, but
> > 0x100000 is common for all Layerscape devices.
> >
> > eTSEC3 is connecting directly to SJA1105 via an RGMII fixed-link, but
> > SJA1105 is currently not supported by uboot. Therefore, eTSEC3 is
> > disabled.
> >
> > Signed-off-by: Xiaoliang Yang <xiaoliang.yang at nxp.com>
> > Signed-off-by: Mingkai Hu <mingkai.hu at nxp.com>
> > Signed-off-by: Jianchao Wang <jianchao.wang at nxp.com>
> > Signed-off-by: Changming Huang <jerry.huang at nxp.com>
> >
> > [Vladimir] Code taken from https://github.com/openil/u-boot (which
> > itself is mostly copied from ls1021a-iot) and adapted with the following
> > changes:
> >
> > - Add a008850 errata workaround
> > - Converted eTSEC, MMC to DM to avoid all build warnings
> > - Plugged in distro boot feature, including support for extlinux.conf
> > - Added defconfig for QSPI boot
> > - Added the board/freescale/ls1021atsn/README.rst for initial setup
> >
> > Signed-off-by: Vladimir Oltean <olteanv at gmail.com>
> > ---
> > arch/arm/Kconfig | 14 +
> > arch/arm/dts/Makefile | 2 +-
> > arch/arm/dts/ls1021a-tsn.dts | 77 ++++
> > board/freescale/ls1021atsn/Kconfig | 18 +
> > board/freescale/ls1021atsn/MAINTAINERS | 8 +
> > board/freescale/ls1021atsn/Makefile | 3 +
> > board/freescale/ls1021atsn/README.rst | 96 +++++
> > board/freescale/ls1021atsn/ls1021atsn.c | 291 +++++++++++++++
> > board/freescale/ls1021atsn/ls102xa_pbi.cfg | 15 +
> > board/freescale/ls1021atsn/ls102xa_rcw_sd.cfg | 8 +
> > configs/ls1021atsn_qspi_defconfig | 76 ++++
> > configs/ls1021atsn_sdcard_defconfig | 85 +++++
> > include/configs/ls1021atsn.h | 346 ++++++++++++++++++
> > 13 files changed, 1038 insertions(+), 1 deletion(-)
> > create mode 100644 arch/arm/dts/ls1021a-tsn.dts
> > create mode 100644 board/freescale/ls1021atsn/Kconfig
> > create mode 100644 board/freescale/ls1021atsn/MAINTAINERS
> > create mode 100644 board/freescale/ls1021atsn/Makefile
> > create mode 100644 board/freescale/ls1021atsn/README.rst
> > create mode 100644 board/freescale/ls1021atsn/ls1021atsn.c
> > create mode 100644 board/freescale/ls1021atsn/ls102xa_pbi.cfg
> > create mode 100644 board/freescale/ls1021atsn/ls102xa_rcw_sd.cfg
> > create mode 100644 configs/ls1021atsn_qspi_defconfig
> > create mode 100644 configs/ls1021atsn_sdcard_defconfig
> > create mode 100644 include/configs/ls1021atsn.h
> >
> > diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
> > index 01ff57cf1bec..5edac7ea2bd5 100644
> > --- a/arch/arm/Kconfig
> > +++ b/arch/arm/Kconfig
> > @@ -1327,6 +1327,19 @@ config TARGET_LS1021ATWR
> > select SUPPORT_SPL
> > imply SCSI
> >
> > +config TARGET_LS1021ATSN
> > + bool "Support ls1021atsn"
> > + select ARCH_LS1021A
> > + select ARCH_SUPPORT_PSCI
> > + select BOARD_EARLY_INIT_F
> > + select BOARD_LATE_INIT
> > + select CPU_V7A
> > + select CPU_V7_HAS_NONSEC
> > + select CPU_V7_HAS_VIRT
> > + select LS1_DEEP_SLEEP
> > + select SUPPORT_SPL
> > + imply SCSI
> > +
> > config TARGET_LS1021AIOT
> > bool "Support ls1021aiot"
> > select ARCH_LS1021A
> > @@ -1693,6 +1706,7 @@ source "board/freescale/ls1028a/Kconfig"
> > source "board/freescale/ls1021aqds/Kconfig"
> > source "board/freescale/ls1043aqds/Kconfig"
> > source "board/freescale/ls1021atwr/Kconfig"
> > +source "board/freescale/ls1021atsn/Kconfig"
> > source "board/freescale/ls1021aiot/Kconfig"
> > source "board/freescale/ls1046aqds/Kconfig"
> > source "board/freescale/ls1043ardb/Kconfig"
> > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> > index 528fb909d5b0..28590b0c5530 100644
> > --- a/arch/arm/dts/Makefile
> > +++ b/arch/arm/dts/Makefile
> > @@ -325,7 +325,7 @@ dtb-$(CONFIG_TARGET_STV0991) += stv0991.dtb
> > dtb-$(CONFIG_ARCH_LS1021A) += ls1021a-qds-duart.dtb \
> > ls1021a-qds-lpuart.dtb \
> > ls1021a-twr-duart.dtb ls1021a-twr-lpuart.dtb \
> > - ls1021a-iot-duart.dtb
> > + ls1021a-iot-duart.dtb ls1021a-tsn.dtb
> > dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \
> > fsl-ls2080a-rdb.dtb \
> > fsl-ls2081a-rdb.dtb \
> > diff --git a/arch/arm/dts/ls1021a-tsn.dts b/arch/arm/dts/ls1021a-tsn.dts
> > new file mode 100644
> > index 000000000000..f633074099dc
> > --- /dev/null
> > +++ b/arch/arm/dts/ls1021a-tsn.dts
> > @@ -0,0 +1,77 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/* Copyright 2016-2018 NXP Semiconductors
> > + * Copyright 2019 Vladimir Oltean <olteanv at gmail.com>
> > + */
> > +
> > +/dts-v1/;
> > +#include "ls1021a.dtsi"
> > +
> > +/ {
> > + model = "NXP LS1021A-TSN Board";
> > +
> > + aliases {
> > + enet0-sgmii-phy = &sgmii_phy2;
> > + enet1-sgmii-phy = &sgmii_phy1;
> > + spi0 = &qspi;
> > + spi1 = &dspi1;
> > + };
> > +};
> > +
> > +&enet0 {
> > + tbi-handle = <&tbi0>;
> > + phy-handle = <&sgmii_phy2>;
> > + phy-mode = "sgmii";
> > + status = "okay";
> > +};
> > +
> > +&enet1 {
> > + tbi-handle = <&tbi1>;
> > + phy-handle = <&sgmii_phy1>;
> > + phy-mode = "sgmii";
> > + status = "okay";
> > +};
> > +
> > +&i2c0 {
> > + status = "okay";
> > +};
> > +
> > +&mdio0 {
> > + /* AR8031 */
> > + sgmii_phy1: ethernet-phy at 1 {
> > + reg = <0x1>;
> > + };
> > +
> > + /* AR8031 */
> > + sgmii_phy2: ethernet-phy at 2 {
> > + reg = <0x2>;
> > + };
> > +
> > + /* SGMII PCS for enet0 */
> > + tbi0: tbi-phy at 1f {
> > + reg = <0x1f>;
> > + device_type = "tbi-phy";
> > + };
> > +};
> > +
> > +&mdio1 {
> > + /* SGMII PCS for enet1 */
> > + tbi1: tbi-phy at 1f {
> > + reg = <0x1f>;
> > + device_type = "tbi-phy";
> > + };
> > +};
> > +
> > +&qspi {
> > + bus-num = <0>;
> > + status = "okay";
> > +
> > + flash at 0 {
> > + compatible = "spi-flash";
> > + spi-max-frequency = <20000000>;
> > + reg = <0>;
> > + };
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > diff --git a/board/freescale/ls1021atsn/Kconfig b/board/freescale/ls1021atsn/Kconfig
> > new file mode 100644
> > index 000000000000..d999fa469002
> > --- /dev/null
> > +++ b/board/freescale/ls1021atsn/Kconfig
> > @@ -0,0 +1,18 @@
> > +# SPDX-License-Identifier: GPL-2.0
> > +if TARGET_LS1021ATSN
> > +
> > +config SYS_BOARD
> > + default "ls1021atsn"
> > +
> > +config SYS_VENDOR
> > + default "freescale"
> > +
> > +config SYS_SOC
> > + default "ls102xa"
> > +
> > +config SYS_CONFIG_NAME
> > + default "ls1021atsn"
> > +
> > +source "board/freescale/common/Kconfig"
> > +
> > +endif
> > diff --git a/board/freescale/ls1021atsn/MAINTAINERS b/board/freescale/ls1021atsn/MAINTAINERS
> > new file mode 100644
> > index 000000000000..560bb615d2fe
> > --- /dev/null
> > +++ b/board/freescale/ls1021atsn/MAINTAINERS
> > @@ -0,0 +1,8 @@
> > +NXP LS1021A-TSN Board
> > +M: Vladimir Oltean <olteanv at gmail.com>
> > +S: Maintained
> > +F: arch/arm/dts/ls1021a-tsn.dts
> > +F: board/freescale/ls1021atsn/
> > +F: include/configs/ls1021atsn.h
> > +F: configs/ls1021atsn_qspi_defconfig
> > +F: configs/ls1021atsn_sdcard_defconfig
> > diff --git a/board/freescale/ls1021atsn/Makefile b/board/freescale/ls1021atsn/Makefile
> > new file mode 100644
> > index 000000000000..b4808f05e8e0
> > --- /dev/null
> > +++ b/board/freescale/ls1021atsn/Makefile
> > @@ -0,0 +1,3 @@
> > +# SPDX-License-Identifier: GPL-2.0
> > +obj-y += ls1021atsn.o
> > +obj-$(CONFIG_ARMV7_PSCI) += ../ls1021atwr/psci.o
> > diff --git a/board/freescale/ls1021atsn/README.rst b/board/freescale/ls1021atsn/README.rst
> > new file mode 100644
> > index 000000000000..e986f460c4d4
> > --- /dev/null
> > +++ b/board/freescale/ls1021atsn/README.rst
> > @@ -0,0 +1,96 @@
> > +.. SPDX-License-Identifier: GPL-2.0
> > +
> > +LS1021A-TSN Board Overview
> > +==========================
> > +
> > + - 1GB DDR3 at 800 MHz
> > + - Spansion/Cypress 64 MB (Rev. A) / 32 MB (Rev. B and C) QSPI NOR flash
> > + - Ethernet
> > + - 2 SGMII 10/100/1G Ethernet ports (Atheros AR8031)
> > + - One SJA1105T switch with 4 Ethernet ports (Broadcom BCM5464R)
> > + - One internal RGMII port connected to the switch
> > + - SDHC
> > + - microSDHC/SDXC connector
> > + - Other I/O
> > + - One Serial port
> > + - Arduino and expansion headers
> > + - mPCIE slot
> > + - SATA port
> > + - USB3.0 port
> > +
> > +LS1021A Memory map
> > +==================
> > +
> > +The addresses in brackets are physical addresses.
> > +
> > +============== ============== ============================== =======
> > +Start Address End Address Description Size
> > +============== ============== ============================== =======
> > +0x00_0000_0000 0x00_000F_FFFF Secure Boot ROM 1MB
> > +0x00_0100_0000 0x00_0FFF_FFFF CCSRBAR 240MB
> > +0x00_1000_0000 0x00_1000_FFFF OCRAM0 64KB
> > +0x00_1001_0000 0x00_1001_FFFF OCRAM1 64KB
> > +0x00_2000_0000 0x00_20FF_FFFF DCSR 16MB
> > +0x00_4000_0000 0x00_5FFF_FFFF QSPI 512MB
> > +0x00_6000_0000 0x00_67FF_FFFF IFC - NOR Flash 128MB
> > +0x00_8000_0000 0x00_FFFF_FFFF DRAM1 2GB
> > +============== ============== ============================== =======
> > +
> > +Compiling and flashing
> > +======================
> > +
> > +The LS1021A-TSN board comes along with a microSD card with OpenIL U-boot.
> > +That will be used to update the internal QSPI flash, as well as
> > +
> > +To compile and flash an SD card image::
> > +
> > + make ls1021atsn_sdcard_defconfig && make -j 8 && sudo cp u-boot-with-spl-pbl.bin /srv/tftpboot/
> > + => tftp 0x82000000 u-boot-with-spl-pbl.bin && mmc rescan && mmc erase 8 0x1100 && mmc write 0x82000000 8 0x1100
> > +
> > +For the QSPI flash, first obtain the Reset Configuration Word binary for
> > +bootimg from the QSPI flash from the rcw project
> > +(https://source.codeaurora.org/external/qoriq/qoriq-components/rcw)::
> > +
> > + make -j 8 && sudo cp ls1021atsn/SSR_PNS_30/rcw_1200_qspiboot.bin.swapped /srv/tftpboot/
> > +
> > +The above RCW binary takes care of swapping the QSPI AMBA memory, so that the
> > +U-boot binary does not need to be swapped when flashing it.
> > +
> > +To compile and flash a U-boot image for QSPI::
> > +
> > + make ls1021atsn_qspi_defconfig && make -j 8 && sudo cp u-boot.bin /srv/tftpboot/
> > +
> > +Then optionally create a custom uboot-env.txt file (although the default
> > +environment already supports distro boot) and convert it to binary format::
> > +
> > + mkenvimage -s 2M -o /srv/tftpboot/uboot-env.bin uboot-env.txt
> > +
> > +To program the QSPI flash with the images::
> > +
> > + => tftp 0x82000000 rcw_1000_qspiboot.bin.swapped && sf probe && sf erase 0x0 +${filesize} && sf write 0x82000000 0x0 ${filesize}
> > + => tftp 0x82000000 u-boot.bin && sf probe && sf erase 0x100000 +${filesize} && sf write 0x82000000 0x100000 ${filesize}
> > + => tftp 0x82000000 uboot-env.bin && sf probe && sf erase 0x400000 +${filesize} && sf write 0x82000000 0x400000 ${filesize}
> > +
> > +The boards contain an AT24 I2C EEPROM that is supposed to hold the MAC
> > +addresses of the Ethernet interfaces, however the EEPROM comes blank out of
> > +the factory, and the MAC addresses are printed on a label on the bottom of
> > +the boards.
> > +
> > +To write the MAC addresses to the EEPROM, the following needs to be done once::
> > +
> > + => mac id
> > + => mac 0 00:1F:7B:xx:xx:xx
> > + => mac 1 00:1F:7B:xx:xx:xx
> > + => mac 2 00:1F:7B:xx:xx:xx
> > + => mac save
> > +
> > +The switch ports do not have their own MAC address - they inherit it from the
> > +master enet2 port.
> > +
> > +Known issues and limitations
> > +============================
> > +
> > +- The 4 SJA1105 switch ports are not functional in U-boot for now.
> > +- Since the IFC pins are multiplexed with QSPI on LS1021A, currently there is
> > + no way to talk to the CPLD for e.g. running the "qixis_reset" command, or
> > + turning the fan on, etc.
> > diff --git a/board/freescale/ls1021atsn/ls1021atsn.c b/board/freescale/ls1021atsn/ls1021atsn.c
> > new file mode 100644
> > index 000000000000..84c2af142956
> > --- /dev/null
> > +++ b/board/freescale/ls1021atsn/ls1021atsn.c
> > @@ -0,0 +1,291 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/* Copyright 2016-2019 NXP Semiconductors
> > + */
> > +#include <common.h>
> > +#include <i2c.h>
> > +#include <asm/io.h>
> > +#include <asm/arch/immap_ls102xa.h>
> > +#include <asm/arch/clock.h>
> > +#include <asm/arch/fsl_serdes.h>
> > +#include <asm/arch-ls102xa/ls102xa_soc.h>
> > +#include <asm/arch/ls102xa_devdis.h>
> > +#include <asm/arch/ls102xa_soc.h>
> > +#include <hwconfig.h>
> > +#include <mmc.h>
> > +#include <fsl_csu.h>
> > +#include <fsl_esdhc.h>
> > +#include <fsl_ifc.h>
> > +#include <fsl_immap.h>
> > +#include <netdev.h>
> > +#include <spl.h>
> > +#include "../common/sleep.h"
> > +#ifdef CONFIG_U_QE
> > +#include <fsl_qe.h>
> > +#endif
> > +#include <fsl_validate.h>
> > +
> > +DECLARE_GLOBAL_DATA_PTR;
> > +
> > +void cpld_show(void)
> > +{
> > + struct ccsr_gur *dcfg = (struct ccsr_gur *)CONFIG_SYS_FSL_GUTS_ADDR;
> > + u32 cpldrev;
> > + int major;
> > + int minor;
> > +
> > + cpldrev = in_be32(&dcfg->gpporcr1);
> > + major = (cpldrev >> 28) & 0xf;
> > + minor = (cpldrev >> 24) & 0xf;
> > +
> > + printf("CPLD: V%d.%d\n", major, minor);
> > +}
> > +
> > +int checkboard(void)
> > +{
> > + puts("Board: LS1021ATSN\n");
> > + cpld_show();
> > + return 0;
> > +}
> > +
> > +void ddrmc_init(void)
> > +{
> > + struct ccsr_ddr *ddr = (struct ccsr_ddr *)CONFIG_SYS_FSL_DDR_ADDR;
> > + u32 temp_sdram_cfg, tmp;
> > +
> > + out_be32(&ddr->sdram_cfg, DDR_SDRAM_CFG);
> > +
> > + out_be32(&ddr->cs0_bnds, DDR_CS0_BNDS);
> > + out_be32(&ddr->cs0_config, DDR_CS0_CONFIG);
> > +
> > + out_be32(&ddr->timing_cfg_0, DDR_TIMING_CFG_0);
> > + out_be32(&ddr->timing_cfg_1, DDR_TIMING_CFG_1);
> > + out_be32(&ddr->timing_cfg_2, DDR_TIMING_CFG_2);
> > + out_be32(&ddr->timing_cfg_3, DDR_TIMING_CFG_3);
> > + out_be32(&ddr->timing_cfg_4, DDR_TIMING_CFG_4);
> > + out_be32(&ddr->timing_cfg_5, DDR_TIMING_CFG_5);
> > +
> > +#ifdef CONFIG_DEEP_SLEEP
> > + if (is_warm_boot()) {
> > + out_be32(&ddr->sdram_cfg_2,
> > + DDR_SDRAM_CFG_2 & ~SDRAM_CFG2_D_INIT);
> > + out_be32(&ddr->init_addr, CONFIG_SYS_SDRAM_BASE);
> > + out_be32(&ddr->init_ext_addr, (1 << 31));
> > +
> > + /* DRAM VRef will not be trained */
> > + out_be32(&ddr->ddr_cdr2,
> > + DDR_DDR_CDR2 & ~DDR_CDR2_VREF_TRAIN_EN);
> > + } else
> > +#endif
> > + {
> > + out_be32(&ddr->sdram_cfg_2, DDR_SDRAM_CFG_2);
> > + out_be32(&ddr->ddr_cdr2, DDR_DDR_CDR2);
> > + }
> > +
> > + out_be32(&ddr->sdram_mode, DDR_SDRAM_MODE);
> > + out_be32(&ddr->sdram_mode_2, DDR_SDRAM_MODE_2);
> > +
> > + out_be32(&ddr->sdram_interval, DDR_SDRAM_INTERVAL);
> > +
> > + out_be32(&ddr->ddr_wrlvl_cntl, DDR_DDR_WRLVL_CNTL);
> > +
> > + out_be32(&ddr->ddr_wrlvl_cntl_2, DDR_DDR_WRLVL_CNTL_2);
> > + out_be32(&ddr->ddr_wrlvl_cntl_3, DDR_DDR_WRLVL_CNTL_3);
> > +
> > + out_be32(&ddr->ddr_cdr1, DDR_DDR_CDR1);
> > +
> > + out_be32(&ddr->sdram_clk_cntl, DDR_SDRAM_CLK_CNTL);
> > + out_be32(&ddr->ddr_zq_cntl, DDR_DDR_ZQ_CNTL);
> > +
> > + out_be32(&ddr->cs0_config_2, DDR_CS0_CONFIG_2);
> > +
> > + /* DDR erratum A-009942 */
> > + tmp = in_be32(&ddr->debug[28]);
> > + out_be32(&ddr->debug[28], tmp | 0x0070006f);
> > +
> > + udelay(1);
> > +
> > +#ifdef CONFIG_DEEP_SLEEP
> > + if (is_warm_boot()) {
> > + /* enter self-refresh */
> > + temp_sdram_cfg = in_be32(&ddr->sdram_cfg_2);
> > + temp_sdram_cfg |= SDRAM_CFG2_FRC_SR;
> > + out_be32(&ddr->sdram_cfg_2, temp_sdram_cfg);
> > +
> > + temp_sdram_cfg = (DDR_SDRAM_CFG_MEM_EN | SDRAM_CFG_BI);
> > + } else
> > +#endif
> > + temp_sdram_cfg = (DDR_SDRAM_CFG_MEM_EN & ~SDRAM_CFG_BI);
> > +
> > + out_be32(&ddr->sdram_cfg, DDR_SDRAM_CFG | temp_sdram_cfg);
> > +
> > +#ifdef CONFIG_DEEP_SLEEP
> > + if (is_warm_boot()) {
> > + /* exit self-refresh */
> > + temp_sdram_cfg = in_be32(&ddr->sdram_cfg_2);
> > + temp_sdram_cfg &= ~SDRAM_CFG2_FRC_SR;
> > + out_be32(&ddr->sdram_cfg_2, temp_sdram_cfg);
> > + }
> > +#endif
> > +}
> > +
> > +int dram_init(void)
> > +{
> > +#if (!defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD))
> > + ddrmc_init();
> > +#endif
> > +
> > + erratum_a008850_post();
> > +
> > + gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
> > +
> > +#if defined(CONFIG_DEEP_SLEEP) && !defined(CONFIG_SPL_BUILD)
> > + fsl_dp_resume();
> > +#endif
> > +
> > + return 0;
> > +}
> > +
> > +int board_eth_init(bd_t *bis)
> > +{
> > + return pci_eth_init(bis);
> > +}
> > +
> > +int board_early_init_f(void)
> > +{
> > + struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
> > +
> > +#ifdef CONFIG_TSEC_ENET
> > + /* Clear BD & FR bits for big endian BD's and frame data (aka set
>
> Nit: Multi-line comment format. I'm curious why checkpatch.pl doesn't
> catch this sometimes.
>
What seems to be the problem with this? Do you prefer to see a first
line with just " /* "?
> > + * correct eTSEC endianness). This is crucial in ensuring that it does
> > + * not report Data Parity Errors in its RX/TX FIFOs when attempting to
> > + * send traffic.
> > + */
> > + clrbits_be32(&scfg->etsecdmamcr, SCFG_ETSECDMAMCR_LE_BD_FR);
> > + /* EC3_GTX_CLK125 (of enet2) used for all RGMII interfaces */
> > + out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125);
> > +#endif
> > +
> > +#ifdef CONFIG_FSL_IFC
> > + init_early_memctl_regs();
> > +#endif
> > +
> > + arch_soc_init();
> > +
> > +#if defined(CONFIG_DEEP_SLEEP)
> > + if (is_warm_boot()) {
> > + timer_init();
> > + dram_init();
> > + }
> > +#endif
> > +
> > + return 0;
> > +}
> > +
> > +#ifdef CONFIG_SPL_BUILD
> > +void board_init_f(ulong dummy)
> > +{
> > + void (*second_uboot)(void);
> > +
> > + /* Clear the BSS */
> > + memset(__bss_start, 0, __bss_end - __bss_start);
> > +
> > + get_clocks();
> > +
> > +#if defined(CONFIG_DEEP_SLEEP)
> > + if (is_warm_boot())
> > + fsl_dp_disable_console();
> > +#endif
> > +
> > + preloader_console_init();
> > +
> > + dram_init();
> > +
> > + /* Allow OCRAM access permission as R/W */
> > +#ifdef CONFIG_LAYERSCAPE_NS_ACCESS
> > + enable_layerscape_ns_access();
> > + enable_layerscape_ns_access();
> > +#endif
> > +
> > + /*
> > + * if it is woken up from deep sleep, then jump to second
> > + * stage uboot and continue executing without recopying
>
> U-Boot
>
> > + * it from SD since it has already been reserved in memory
> > + * in last boot.
> > + */
> > + if (is_warm_boot()) {
> > + second_uboot = (void (*)(void))CONFIG_SYS_TEXT_BASE;
> > + second_uboot();
> > + }
> > +
> > + board_init_r(NULL, 0);
> > +}
> > +#endif
> > +
> > +int board_init(void)
> > +{
> > +#ifndef CONFIG_SYS_FSL_NO_SERDES
> > + fsl_serdes_init();
> > +#endif
> > + ls102xa_smmu_stream_id_init();
> > +
> > +#ifdef CONFIG_LAYERSCAPE_NS_ACCESS
> > + enable_layerscape_ns_access();
> > +#endif
> > +
> > +#ifdef CONFIG_U_QE
> > + u_qe_init();
> > +#endif
> > +
> > + return 0;
> > +}
> > +
> > +#if defined(CONFIG_SPL_BUILD)
> > +void spl_board_init(void)
> > +{
> > + ls102xa_smmu_stream_id_init();
> > +}
> > +#endif
> > +
> > +#ifdef CONFIG_BOARD_LATE_INIT
> > +int board_late_init(void)
> > +{
> > +#ifdef CONFIG_CHAIN_OF_TRUST
> > + fsl_setenv_chain_of_trust();
> > +#endif
> > +
> > + return 0;
> > +}
> > +#endif
> > +
> > +#if defined(CONFIG_MISC_INIT_R)
> > +int misc_init_r(void)
> > +{
> > +#ifdef CONFIG_FSL_DEVICE_DISABLE
> > + device_disable(devdis_tbl, ARRAY_SIZE(devdis_tbl));
> > +#endif
> > +
> > +#ifdef CONFIG_FSL_CAAM
> > + return sec_init();
> > +#endif
> > +}
> > +#endif
> > +
> > +#if defined(CONFIG_DEEP_SLEEP)
> > +void board_sleep_prepare(void)
> > +{
> > +#ifdef CONFIG_LAYERSCAPE_NS_ACCESS
> > + enable_layerscape_ns_access();
> > +#endif
> > +}
> > +#endif
> > +
> > +int ft_board_setup(void *blob, bd_t *bd)
> > +{
> > + ft_cpu_setup(blob, bd);
> > +
> > +#ifdef CONFIG_PCI
> > + ft_pci_setup(blob, bd);
> > +#endif
> > +
> > + return 0;
> > +}
> > diff --git a/board/freescale/ls1021atsn/ls102xa_pbi.cfg b/board/freescale/ls1021atsn/ls102xa_pbi.cfg
> > new file mode 100644
> > index 000000000000..a8ba184c6684
> > --- /dev/null
> > +++ b/board/freescale/ls1021atsn/ls102xa_pbi.cfg
>
> What is this file? Is it built by something?
>
Yes, search for CONFIG_SYS_FSL_PBL_PBI in include/configs/ls1021atsn.h
and in the main Makefile.
So the boot ROM of the SoC searches for a 512-bit wide data structure
starting with sector 8 of the MMC called RCW (Reset Configuration
Word). This defines PLL frequencies, SerDes protocols, pinmuxing etc
on the SoC. The RCW can also have a sequence of PBL (Pre-Boot Loader)
commands appended to it - generally these are memory write operations
that do stuff such as errata workarounds before the execution
transfers to the boot loader. Actually I believe, but can't prove,
that it is the PBL who copies the U-Boot SPL from MMC into an internal
SRAM called OCRAM (on-chip RAM) before transferring the execution to
it. I say I can't prove this because I would have expected to
recognize this block copy command in the file you asked about.
The takeaway is that for MMC-based booting, the RCW and PBI commands
are packaged together in a file called u-boot-with-spl-pbl.bin. For
QSPI-based booting that is not the case - the SPL and the OCRAM are
not involved because the QSPI flash is memory-mapped so the CPU can
execute the U-Boot image directly. In the case of booting from QSPI
flash, the RCW and PBL commands are not packaged with the U-Boot
image, but instead you're supposed to flash them separately. To be
honest I don't know why it is like that - I'm not a big fan of keeping
a relatively opaque hex dump of the RCW and PBL commands in U-Boot
(let alone that the process is not the same for all boot sources).
> > @@ -0,0 +1,15 @@
> > +#PBI commands
> > +
> > +09570200 ffffffff
> > +09570158 00000300
> > +8940007c 21f47300
> > +
> > +# Configure Scratch register
> > +09ee0200 10000000
> > +# Configure alternate space
> > +09570158 00001000
> > +# Flush PBL data
> > +096100c0 000FFFFF
> > +
> > +09ea085c 00502880
> > +09ea0560 80800000
> > diff --git a/board/freescale/ls1021atsn/ls102xa_rcw_sd.cfg b/board/freescale/ls1021atsn/ls102xa_rcw_sd.cfg
> > new file mode 100644
> > index 000000000000..67152dd2810e
> > --- /dev/null
> > +++ b/board/freescale/ls1021atsn/ls102xa_rcw_sd.cfg
> > @@ -0,0 +1,8 @@
> > +# PBL preamble and RCW header
> > +aa55aa55 01ee0100
> > +
> > +# Disable IFC, enable QSPI and DSPI
> > +0608000c 00000000 00000000 00000000
> > +30000000 08007900 60040a00 21046000
> > +00000000 00000000 00000000 20002000
> > +20024800 8804b340 00000000 00000000
> > diff --git a/configs/ls1021atsn_qspi_defconfig b/configs/ls1021atsn_qspi_defconfig
> > new file mode 100644
> > index 000000000000..427881fe0c52
> > --- /dev/null
> > +++ b/configs/ls1021atsn_qspi_defconfig
> > @@ -0,0 +1,76 @@
> > +CONFIG_ARM=y
> > +CONFIG_TARGET_LS1021ATSN=y
> > +CONFIG_SYS_TEXT_BASE=0x40100000
> > +CONFIG_DEFAULT_DEVICE_TREE="ls1021a-tsn"
> > +CONFIG_BOARD_EARLY_INIT_F=y
> > +CONFIG_SYS_FSL_CLK=y
> > +CONFIG_SYS_EXTRA_OPTIONS="QSPI_BOOT"
> > +CONFIG_QSPI_BOOT=y
> > +CONFIG_BOOTDELAY=3
> > +CONFIG_HUSH_PARSER=y
> > +CONFIG_CMD_GREPENV=y
> > +CONFIG_CMD_MEMINFO=y
> > +CONFIG_CMD_GPT=y
> > +CONFIG_CMD_FAT=y
> > +CONFIG_FSL_ESDHC=y
> > +CONFIG_CMD_SF=y
> > +CONFIG_OF_CONTROL=y
> > +CONFIG_ENV_IS_IN_SPI_FLASH=y
> > +CONFIG_DM=y
> > +CONFIG_FSL_CAAM=y
> > +CONFIG_SPI=y
> > +CONFIG_SPI_FLASH=y
> > +CONFIG_SPI_FLASH_ATMEL=y
> > +CONFIG_SPI_FLASH_STMICRO=y
> > +CONFIG_SPI_FLASH_BAR=y
> > +CONFIG_SPI_FLASH_SPANSION=y
> > +CONFIG_NETDEVICES=y
> > +CONFIG_DM_ETH=y
> > +CONFIG_TSEC_ENET=y
> > +CONFIG_MII=y
> > +CONFIG_SYS_NS16550=y
> > +CONFIG_DM_SPI=y
> > +CONFIG_DM_SPI_FLASH=y
> > +CONFIG_SPI_FLASH_DATAFLASH=y
> > +CONFIG_FSL_DSPI=y
> > +CONFIG_FSL_QSPI=y
> > +CONFIG_PCI=y
> > +CONFIG_CMD_PCI=y
> > +CONFIG_DM_PCI=y
> > +CONFIG_DM_PCI_COMPAT=y
> > +CONFIG_CMD_MMC=y
> > +CONFIG_DM_MMC=y
> > +CONFIG_FSL_SPI_ALIGNED_TXFIFO=y
> > +CONFIG_USB=y
> > +CONFIG_DM_USB=y
> > +CONFIG_CMD_USB=y
> > +CONFIG_USB_XHCI_HCD=y
> > +CONFIG_USB_XHCI_FSL=y
> > +CONFIG_USB_XHCI_DWC3=y
> > +CONFIG_HAS_FSL_XHCI_USB=y
> > +CONFIG_USB_STORAGE=y
> > +CONFIG_CMD_EXT2=y
> > +CONFIG_PCIE_LAYERSCAPE=y
> > +CONFIG_PHYLIB=y
> > +CONFIG_PHY_GIGE=y
> > +CONFIG_PHY_ATHEROS=y
> > +CONFIG_PHY_BROADCOM=y
> > +CONFIG_PHY_FIXED=y
> > +CONFIG_CMD_PING=y
> > +CONFIG_CMD_DHCP=y
> > +CONFIG_CMD_MII=y
> > +CONFIG_CMDLINE_TAG=y
> > +CONFIG_CMDLINE_EDITING=y
> > +CONFIG_AUTO_COMPLETE=y
> > +CONFIG_NR_DRAM_BANKS=1
> > +CONFIG_CMD_BOOTZ=y
> > +CONFIG_SYS_LONGHELP=y
> > +CONFIG_FIT=y
> > +CONFIG_CMD_DM=y
> > +CONFIG_AHCI=y
> > +CONFIG_CMD_I2C=y
> > +CONFIG_BLK=y
> > +CONFIG_CMD_PART=y
> > +CONFIG_CMD_FS_GENERIC=y
> > +CONFIG_CMD_FS_UUID=y
> > +CONFIG_DISTRO_DEFAULTS=y
> > diff --git a/configs/ls1021atsn_sdcard_defconfig b/configs/ls1021atsn_sdcard_defconfig
> > new file mode 100644
> > index 000000000000..b74e01206817
> > --- /dev/null
> > +++ b/configs/ls1021atsn_sdcard_defconfig
> > @@ -0,0 +1,85 @@
> > +CONFIG_ARM=y
> > +CONFIG_TARGET_LS1021ATSN=y
> > +CONFIG_SPL_TEXT_BASE=0x10000000
> > +CONFIG_SYS_TEXT_BASE=0x82000000
> > +CONFIG_DEFAULT_DEVICE_TREE="ls1021a-tsn"
> > +CONFIG_BOARD_EARLY_INIT_F=y
> > +CONFIG_SPL=y
> > +CONFIG_SPL_FRAMEWORK=y
> > +CONFIG_SYS_FSL_CLK=y
> > +CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPL_FSL_PBL,SD_BOOT,SD_BOOT_QSPI"
> > +CONFIG_SD_BOOT=y
> > +CONFIG_BOOTDELAY=3
> > +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
> > +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xe8
> > +CONFIG_HUSH_PARSER=y
> > +CONFIG_CMD_GREPENV=y
> > +CONFIG_CMD_MEMINFO=y
> > +CONFIG_CMD_GPT=y
> > +CONFIG_CMD_FAT=y
> > +CONFIG_CMD_MMC=y
> > +CONFIG_FSL_ESDHC=y
> > +CONFIG_CMD_SF=y
> > +CONFIG_OF_CONTROL=y
> > +CONFIG_ENV_IS_IN_MMC=y
> > +CONFIG_DM=y
> > +CONFIG_FSL_CAAM=y
> > +CONFIG_SPI=y
> > +CONFIG_SPI_FLASH=y
> > +CONFIG_SPI_FLASH_ATMEL=y
> > +CONFIG_SPI_FLASH_STMICRO=y
> > +CONFIG_SPI_FLASH_BAR=y
> > +CONFIG_SPI_FLASH_SPANSION=y
> > +CONFIG_NETDEVICES=y
> > +CONFIG_DM_ETH=y
> > +CONFIG_TSEC_ENET=y
> > +CONFIG_MII=y
> > +CONFIG_SYS_NS16550=y
> > +CONFIG_DM_SPI=y
> > +CONFIG_DM_SPI_FLASH=y
> > +CONFIG_SPI_FLASH_DATAFLASH=y
> > +CONFIG_FSL_DSPI=y
> > +CONFIG_FSL_QSPI=y
> > +CONFIG_PCI=y
> > +CONFIG_CMD_PCI=y
> > +CONFIG_DM_PCI=y
> > +CONFIG_DM_PCI_COMPAT=y
> > +CONFIG_USB=y
> > +CONFIG_DM_USB=y
> > +CONFIG_CMD_USB=y
> > +CONFIG_USB_XHCI_HCD=y
> > +CONFIG_USB_XHCI_FSL=y
> > +CONFIG_USB_XHCI_DWC3=y
> > +CONFIG_HAS_FSL_XHCI_USB=y
> > +CONFIG_USB_STORAGE=y
> > +CONFIG_CMD_EXT2=y
> > +CONFIG_PCIE_LAYERSCAPE=y
> > +CONFIG_PHYLIB=y
> > +CONFIG_PHY_GIGE=y
> > +CONFIG_PHY_ATHEROS=y
> > +CONFIG_PHY_BROADCOM=y
> > +CONFIG_PHY_FIXED=y
> > +CONFIG_CMD_PING=y
> > +CONFIG_CMD_DHCP=y
> > +CONFIG_CMD_MII=y
> > +CONFIG_CMDLINE_TAG=y
> > +CONFIG_CMDLINE_EDITING=y
> > +CONFIG_AUTO_COMPLETE=y
> > +CONFIG_NR_DRAM_BANKS=1
> > +CONFIG_CMD_BOOTZ=y
> > +CONFIG_SYS_LONGHELP=y
> > +CONFIG_FIT=y
> > +CONFIG_SPL_MMC_SUPPORT=y
> > +CONFIG_SPL_SERIAL_SUPPORT=y
> > +CONFIG_SPL_I2C_SUPPORT=y
> > +CONFIG_SPL_ENV_SUPPORT=y
> > +CONFIG_SPL_LIBCOMMON_SUPPORT=y
> > +CONFIG_CMD_DM=y
> > +CONFIG_AHCI=y
> > +CONFIG_CMD_I2C=y
> > +CONFIG_BLK=y
> > +CONFIG_DM_MMC=y
> > +CONFIG_CMD_PART=y
> > +CONFIG_CMD_FS_GENERIC=y
> > +CONFIG_CMD_FS_UUID=y
> > +CONFIG_DISTRO_DEFAULTS=y
> > diff --git a/include/configs/ls1021atsn.h b/include/configs/ls1021atsn.h
> > new file mode 100644
> > index 000000000000..c8ec414afd39
> > --- /dev/null
> > +++ b/include/configs/ls1021atsn.h
> > @@ -0,0 +1,346 @@
> > +/* SPDX-License-Identifier: GPL-2.0
> > + * Copyright 2016-2018 NXP Semiconductors
> > + * Copyright 2019 Vladimir Oltean <olteanv at gmail.com>
> > + */
> > +
> > +#ifndef __CONFIG_H
> > +#define __CONFIG_H
> > +
> > +#define CONFIG_ARMV7_SECURE_BASE OCRAM_BASE_S_ADDR
> > +
> > +#define CONFIG_SYS_FSL_CLK
> > +
> > +#define CONFIG_DEEP_SLEEP
> > +#ifdef CONFIG_DEEP_SLEEP
> > +#define CONFIG_SILENT_CONSOLE
> > +#endif
> > +
> > +/*
> > + * Size of malloc() pool
> > + */
> > +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 16 * 1024 * 1024)
> > +
> > +#define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR
> > +#define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE
> > +
> > +/* XHCI Support - enabled by default */
> > +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
> > +
> > +#define CONFIG_SYS_CLK_FREQ 100000000
> > +#define CONFIG_DDR_CLK_FREQ 100000000
> > +
> > +#define DDR_SDRAM_CFG 0x470c0008
> > +#define DDR_CS0_BNDS 0x008000bf
> > +#define DDR_CS0_CONFIG 0x80014302
> > +#define DDR_TIMING_CFG_0 0x50550004
> > +#define DDR_TIMING_CFG_1 0xbcb38c56
> > +#define DDR_TIMING_CFG_2 0x0040d120
> > +#define DDR_TIMING_CFG_3 0x010e1000
> > +#define DDR_TIMING_CFG_4 0x00000001
> > +#define DDR_TIMING_CFG_5 0x03401400
> > +#define DDR_SDRAM_CFG_2 0x00401010
> > +#define DDR_SDRAM_MODE 0x00061c60
> > +#define DDR_SDRAM_MODE_2 0x00180000
> > +#define DDR_SDRAM_INTERVAL 0x18600618
> > +#define DDR_DDR_WRLVL_CNTL 0x8655f605
> > +#define DDR_DDR_WRLVL_CNTL_2 0x05060607
> > +#define DDR_DDR_WRLVL_CNTL_3 0x05050505
> > +#define DDR_DDR_CDR1 0x80040000
> > +#define DDR_DDR_CDR2 0x00000001
> > +#define DDR_SDRAM_CLK_CNTL 0x02000000
> > +#define DDR_DDR_ZQ_CNTL 0x89080600
> > +#define DDR_CS0_CONFIG_2 0
> > +#define DDR_SDRAM_CFG_MEM_EN 0x80000000
> > +#define SDRAM_CFG2_D_INIT 0x00000010
> > +#define DDR_CDR2_VREF_TRAIN_EN 0x00000080
> > +#define SDRAM_CFG2_FRC_SR 0x80000000
> > +#define SDRAM_CFG_BI 0x00000001
> > +
> > +#define CONFIG_CHIP_SELECTS_PER_CTRL 4
> > +
> > +#ifdef CONFIG_RAMBOOT_PBL
> > +#define CONFIG_SYS_FSL_PBL_PBI \
> > + "board/freescale/ls1021atsn/ls102xa_pbi.cfg"
> > +#endif
> > +
> > +#ifdef CONFIG_SD_BOOT
> > +#ifdef CONFIG_SD_BOOT_QSPI
> > +#define CONFIG_SYS_FSL_PBL_RCW \
> > + "board/freescale/ls1021atsn/ls102xa_rcw_sd_qspi.cfg"
> > +#else
> > +#define CONFIG_SYS_FSL_PBL_RCW \
> > + "board/freescale/ls1021atsn/ls102xa_rcw_sd_ifc.cfg"
> > +#endif
> > +#define CONFIG_SPL_LDSCRIPT "arch/$(ARCH)/cpu/u-boot-spl.lds"
> > +#define CONFIG_SPL_LIBGENERIC_SUPPORT
> > +#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
> > +#define CONFIG_SPL_WATCHDOG_SUPPORT
> > +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0xe8
> > +
> > +#ifdef CONFIG_SECURE_BOOT
> > +#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
> > +#endif /* ifdef CONFIG_SECURE_BOOT */
> > +
> > +#define CONFIG_SPL_MAX_SIZE 0x1a000
> > +#define CONFIG_SPL_STACK 0x1001d000
> > +#define CONFIG_SPL_PAD_TO 0x1c000
> > +
> > +#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \
> > + CONFIG_SYS_MONITOR_LEN)
> > +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
> > +#define CONFIG_SPL_BSS_START_ADDR 0x80100000
> > +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
> > +
> > +#ifdef CONFIG_U_BOOT_HDR_SIZE
> > +/*
> > + * HDR would be appended at end of image and copied to DDR along
> > + * with U-Boot image. Here u-boot max. size is 512K. So if binary
>
> U-Boot (second one).
>
> > + * size increases then increase this size in case of secure boot as
> > + * it uses raw u-boot image instead of fit image.
>
> U-Boot
>
> > + */
> > +#define CONFIG_SYS_MONITOR_LEN (0x80000 + CONFIG_U_BOOT_HDR_SIZE)
> > +#else
> > +#define CONFIG_SYS_MONITOR_LEN 0x80000
> > +#endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */
> > +#endif
> > +
> > +#define CONFIG_NR_DRAM_BANKS 1
> > +#define PHYS_SDRAM 0x80000000
> > +#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
> > +
> > +#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
> > +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
> > +
> > +#define CONFIG_CHIP_SELECTS_PER_CTRL 4
> > +
> > +#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_NAND_BOOT) && \
> > + !defined(CONFIG_QSPI_BOOT)
> > +#define CONFIG_U_QE
> > +#endif
> > +
> > +/*
> > + * IFC Definitions
> > + */
> > +#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
> > +#define CONFIG_FSL_IFC
> > +#endif
> > +
> > +/* CPLD */
> > +#define CONFIG_SYS_CPLD_BASE 0x7fb00000
> > +#define CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE
> > +
> > +#define CONFIG_SYS_FPGA_CSPR_EXT (0x0)
> > +#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \
> > + CSPR_PORT_SIZE_8 | \
> > + CSPR_MSEL_GPCM | \
> > + CSPR_V)
> > +#define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64 * 1024)
> > +#define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \
> > + CSOR_NOR_NOR_MODE_AVD_NOR | \
> > + CSOR_NOR_TRHZ_80)
> > +
> > +/* CPLD Timing parameters for IFC GPCM */
> > +#define CONFIG_SYS_FPGA_FTIM0 (FTIM0_GPCM_TACSE(0xf) | \
> > + FTIM0_GPCM_TEADC(0xf) | \
> > + FTIM0_GPCM_TEAHC(0xf))
> > +#define CONFIG_SYS_FPGA_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
> > + FTIM1_GPCM_TRAD(0x3f))
> > +#define CONFIG_SYS_FPGA_FTIM2 (FTIM2_GPCM_TCS(0xf) | \
> > + FTIM2_GPCM_TCH(0xf) | \
> > + FTIM2_GPCM_TWP(0xff))
> > +#define CONFIG_SYS_FPGA_FTIM3 0x0
> > +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_FPGA_CSPR_EXT
> > +#define CONFIG_SYS_CSPR0 CONFIG_SYS_FPGA_CSPR
> > +#define CONFIG_SYS_AMASK0 CONFIG_SYS_FPGA_AMASK
> > +#define CONFIG_SYS_CSOR0 CONFIG_SYS_FPGA_CSOR
> > +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_FPGA_FTIM0
> > +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_FPGA_FTIM1
> > +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_FPGA_FTIM2
> > +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_FPGA_FTIM3
> > +
> > +/*
> > + * Serial Port
> > + */
> > +#define CONFIG_CONS_INDEX 1
> > +#define CONFIG_SYS_NS16550_SERIAL
> > +#ifndef CONFIG_DM_SERIAL
> > +#define CONFIG_SYS_NS16550_REG_SIZE 1
> > +#endif
> > +#define CONFIG_SYS_NS16550_CLK get_serial_clock()
> > +
> > +#define CONFIG_BAUDRATE 115200
> > +
> > +/*
> > + * I2C
> > + */
> > +#define CONFIG_SYS_I2C
> > +#define CONFIG_SYS_I2C_MXC
> > +#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
> > +#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
> > +#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
> > +
> > +/* EEPROM */
> > +#define CONFIG_ID_EEPROM
> > +#define CONFIG_SYS_I2C_EEPROM_NXID
> > +#define CONFIG_SYS_EEPROM_BUS_NUM 0
> > +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x51
> > +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
> > +
> > +/* SPI */
> > +#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
> > +/* QSPI */
> > +#define FSL_QSPI_FLASH_SIZE (1 << 24)
> > +#define FSL_QSPI_FLASH_NUM 2
> > +/* DSPI */
> > +#endif
> > +
> > +#ifdef CONFIG_TSEC_ENET
> > +#define CONFIG_ETHPRIME "ethernet at 2d10000"
>
> Where does this name come from? Is this not the first mac, i.e. would
> you get this without the explicit setting ethprime?
>
I don't know, I didn't try not setting this. It is the first MAC, yes.
> > +#endif
> > +
> > +/* PCIe */
> > +#define CONFIG_PCIE1 /* PCIE controller 1 */
> > +#define CONFIG_PCIE2 /* PCIE controller 2 */
> > +#define FSL_PCIE_COMPAT "fsl,ls1021a-pcie"
> > +#ifdef CONFIG_PCI
> > +#define CONFIG_PCI_SCAN_SHOW
> > +#endif
> > +
> > +#define CONFIG_PEN_ADDR_BIG_ENDIAN
> > +#define CONFIG_LAYERSCAPE_NS_ACCESS
> > +#define CONFIG_SMP_PEN_ADDR 0x01ee0200
> > +#define COUNTER_FREQUENCY 12500000
> > +
> > +#define CONFIG_HWCONFIG
> > +#define HWCONFIG_BUFFER_SIZE 256
> > +
> > +#define CONFIG_FSL_DEVICE_DISABLE
> > +
> > +#define BOOT_TARGET_DEVICES(func) \
> > + func(MMC, mmc, 0) \
> > + func(USB, usb, 0) \
> > + func(DHCP, dhcp, na)
> > +#include <config_distro_bootcmd.h>
> > +
> > +#define CONFIG_EXTRA_ENV_SETTINGS \
> > + "bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \
> > + "initrd_high=0xffffffff\0" \
> > + "fdt_high=0xffffffff\0" \
> > + "fdt_addr=0x64f00000\0" \
> > + "kernel_addr=0x61000000\0" \
> > + "kernelheader_addr=0x60800000\0" \
> > + "scriptaddr=0x80000000\0" \
> > + "scripthdraddr=0x80080000\0" \
> > + "fdtheader_addr_r=0x80100000\0" \
> > + "kernelheader_addr_r=0x80200000\0" \
> > + "kernel_addr_r=0x80008000\0" \
> > + "kernelheader_size=0x40000\0" \
> > + "fdt_addr_r=0x8f000000\0" \
> > + "ramdisk_addr_r=0xa0000000\0" \
> > + "load_addr=0x80008000\0" \
> > + "kernel_size=0x2800000\0" \
> > + "kernel_addr_sd=0x8000\0" \
> > + "kernel_size_sd=0x14000\0" \
> > + "kernelhdr_addr_sd=0x4000\0" \
> > + "kernelhdr_size_sd=0x10\0" \
> > + BOOTENV \
> > + "boot_scripts=ls1021atsn_boot.scr\0" \
> > + "boot_script_hdr=hdr_ls1021atsn_bs.out\0" \
> > + "scan_dev_for_boot_part=" \
> > + "part list ${devtype} ${devnum} devplist; " \
> > + "env exists devplist || setenv devplist 1; " \
> > + "for distro_bootpart in ${devplist}; do " \
> > + "if fstype ${devtype} " \
> > + "${devnum}:${distro_bootpart} " \
> > + "bootfstype; then " \
> > + "run scan_dev_for_boot; " \
> > + "fi; " \
> > + "done\0" \
> > + "scan_dev_for_boot=" \
> > + "echo Scanning ${devtype} " \
> > + "${devnum}:${distro_bootpart}...; " \
> > + "for prefix in ${boot_prefixes}; do " \
> > + "run scan_dev_for_scripts; " \
> > + "run scan_dev_for_extlinux; " \
> > + "done;" \
> > + "\0" \
> > + "boot_a_script=" \
> > + "load ${devtype} ${devnum}:${distro_bootpart} " \
> > + "${scriptaddr} ${prefix}${script}; " \
> > + "env exists secureboot && load ${devtype} " \
> > + "${devnum}:${distro_bootpart} " \
> > + "${scripthdraddr} ${prefix}${boot_script_hdr} " \
> > + "&& esbc_validate ${scripthdraddr};" \
> > + "source ${scriptaddr}\0" \
> > + "qspi_bootcmd=echo Trying load from qspi..;" \
> > + "sf probe && sf read $load_addr " \
> > + "$kernel_addr $kernel_size; env exists secureboot " \
> > + "&& sf read $kernelheader_addr_r $kernelheader_addr " \
> > + "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
> > + "bootm $load_addr#$board\0" \
> > + "sd_bootcmd=echo Trying load from SD ..;" \
> > + "mmcinfo && mmc read $load_addr " \
> > + "$kernel_addr_sd $kernel_size_sd && " \
> > + "env exists secureboot && mmc read $kernelheader_addr_r " \
> > + "$kernelhdr_addr_sd $kernelhdr_size_sd " \
> > + " && esbc_validate ${kernelheader_addr_r};" \
> > + "bootm $load_addr#$board\0"
> > +
> > +#undef CONFIG_BOOTCOMMAND
> > +#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
> > +#define CONFIG_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; " \
> > + "env exists secureboot && esbc_halt"
> > +#elif defined(CONFIG_SD_BOOT)
> > +#define CONFIG_BOOTCOMMAND "run distro_bootcmd; run sd_bootcmd; " \
> > + "env exists secureboot && esbc_halt;"
> > +#endif
> > +
> > +/*
> > + * Miscellaneous configurable options
> > + */
> > +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
> > +#define CONFIG_SYS_PBSIZE \
> > + (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
> > +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
> > +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
> > +
> > +#define CONFIG_SYS_LOAD_ADDR 0x82000000
> > +
> > +#define CONFIG_LS102XA_STREAM_ID
> > +
> > +#define CONFIG_SYS_INIT_SP_OFFSET \
> > + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
> > +#define CONFIG_SYS_INIT_SP_ADDR \
> > + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
> > +
> > +#ifdef CONFIG_SPL_BUILD
> > +#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
> > +#else
> > +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
> > +#endif
> > +
> > +#define CONFIG_SYS_QE_FW_ADDR 0x67f40000
> > +
> > +/*
> > + * Environment
> > + */
> > +#define CONFIG_ENV_OVERWRITE
> > +
> > +#if defined(CONFIG_SD_BOOT)
> > +#define CONFIG_ENV_OFFSET 0x300000
> > +#define CONFIG_SYS_MMC_ENV_DEV 0
> > +#define CONFIG_ENV_SIZE 0x20000
> > +#elif defined(CONFIG_QSPI_BOOT)
> > +#define CONFIG_ENV_SIZE 0x2000
> > +#define CONFIG_ENV_OFFSET 0x300000
> > +#define CONFIG_ENV_SECT_SIZE 0x40000
> > +#endif
> > +
> > +#define CONFIG_OF_BOARD_SETUP
> > +#define CONFIG_OF_STDOUT_VIA_ALIAS
> > +#define CONFIG_MISC_INIT_R
> > +
> > +#include <asm/fsl_secure_boot.h>
> > +#define CONFIG_SYS_BOOTM_LEN 0x8000000 /* 128 MB */
> > +
> > +#endif
> > --
> > 2.17.1
> >
> > _______________________________________________
> > U-Boot mailing list
> > U-Boot at lists.denx.de
> > https://lists.denx.de/listinfo/u-boot
Thanks,
-Vladimir
More information about the U-Boot
mailing list