[PATCH v4 00/12] riscv: Add FPIOA and GPIO support for Kendryte K210

Sean Anderson seanga2 at gmail.com
Wed Aug 12 16:03:11 CEST 2020


On 6/24/20 6:29 AM, Sean Anderson wrote:
> This patch series adds support for pinmuxing, gpios, and leds on the Kendyte
> K210.
> 
> This patch series was previously part of
> https://patchwork.ozlabs.org/project/uboot/list/?series=161576
> 
> This patch series depends on
> https://patchwork.ozlabs.org/project/uboot/list/?series=178480
> 
> Changes in v4:
> - Add sandbox dt-binding headers to MAINTAINERS
> - Add test for led behavior
> - Add test/dm/pinmux.c to patch
> - Move sandbox_* variables into a priv structure. This resets them to the
>   default state every time we re-probe.
> - Reformat documentation in dm/pinctrl.h
> 
> Changes in v3:
> - Add dt-bindings/pinctrl/sandbox-pinmux.h to patch
> 
> Changes in v2:
> - Add test for pinmuxing
> - Don't clear existing pinctrl settings on probe
> - Re-order GPIOs to match the defaults more closely
> - Rebase onto v13 of "riscv: Add Sipeed Maix support"
> - Rewrite FPIOA driver to use pinmux property
> - Support muxing the output enable signal for each function in the FPIOA
> - Support output and input inversion in the pinmux driver
> - Support pinmux property in pinctrl-generic
> 
> Sean Anderson (12):
>   pinctrl: Add pinmux property support to pinctrl-generic
>   pinctrl: Reformat documentation in dm/pinctrl.h
>   test: pinmux: Add test for pin muxing
>   pinctrl: Add support for Kendryte K210 FPIOA
>   gpio: sifive: Use generic reg read function
>   gpio: dw: Fix warnings about casting int to pointer
>   gpio: dw: Add a trailing underscore to generated name
>   gpio: dw: Return output value when direction is out
>   led: gpio: Default to using node name if label is absent
>   test: dm: Test for default led naming
>   riscv: Add pinmux and gpio bindings for Kendryte K210
>   riscv: Add FPIOA and GPIO support for Kendryte K210
> 
>  MAINTAINERS                                   |   3 +
>  arch/riscv/dts/k210-maix-bit.dts              | 104 +++
>  arch/riscv/dts/k210.dtsi                      |  12 +
>  arch/sandbox/dts/test.dts                     |  47 +-
>  board/sipeed/maix/Kconfig                     |   9 +
>  doc/board/sipeed/maix.rst                     |  64 +-
>  .../pinctrl/kendryte,k210-fpioa.txt           | 102 +++
>  .../pinctrl/pinctrl-bindings.txt              |  65 +-
>  drivers/gpio/dwapb_gpio.c                     |  33 +-
>  drivers/gpio/sifive-gpio.c                    |   2 +-
>  drivers/led/led_gpio.c                        |   7 +-
>  drivers/pinctrl/Kconfig                       |   1 +
>  drivers/pinctrl/Makefile                      |   1 +
>  drivers/pinctrl/kendryte/Kconfig              |   7 +
>  drivers/pinctrl/kendryte/Makefile             |   1 +
>  drivers/pinctrl/kendryte/pinctrl.c            | 678 ++++++++++++++++++
>  drivers/pinctrl/kendryte/pinctrl.h            |  70 ++
>  drivers/pinctrl/pinctrl-generic.c             | 125 +++-
>  drivers/pinctrl/pinctrl-sandbox.c             | 186 +++--
>  include/dm/pinctrl.h                          | 360 +++++++---
>  include/dt-bindings/pinctrl/k210-pinctrl.h    | 277 +++++++
>  include/dt-bindings/pinctrl/sandbox-pinmux.h  |  19 +
>  test/dm/Makefile                              |   3 +
>  test/dm/led.c                                 |   3 +-
>  test/dm/pinmux.c                              |  57 ++
>  test/py/tests/test_pinmux.py                  |  36 +-
>  26 files changed, 2027 insertions(+), 245 deletions(-)
>  create mode 100644 doc/device-tree-bindings/pinctrl/kendryte,k210-fpioa.txt
>  create mode 100644 drivers/pinctrl/kendryte/Kconfig
>  create mode 100644 drivers/pinctrl/kendryte/Makefile
>  create mode 100644 drivers/pinctrl/kendryte/pinctrl.c
>  create mode 100644 drivers/pinctrl/kendryte/pinctrl.h
>  create mode 100644 include/dt-bindings/pinctrl/k210-pinctrl.h
>  create mode 100644 include/dt-bindings/pinctrl/sandbox-pinmux.h
>  create mode 100644 test/dm/pinmux.c
> 

Rick can you put this in your rc3 PR? I think there are reviews for all
patches in this series.

--Sean


More information about the U-Boot mailing list