[Uboot-stm32] [PATCH 04/11] board: stm32mp1: use IS_ENABLED to prevent ifdef in sysconf_init

Patrice CHOTARD patrice.chotard at st.com
Thu Aug 13 11:50:25 CEST 2020


On 8/13/20 9:23 AM, Patrice CHOTARD wrote:
> Hi Patrick
>
> On 7/31/20 4:31 PM, Patrick Delaunay wrote:
>> Use IS_ENABLED to prevent ifdef in sysconf_init.
>>
>> Signed-off-by: Patrick Delaunay <patrick.delaunay at st.com>
>> ---
>>
>>  board/st/stm32mp1/stm32mp1.c | 11 +++--------
>>  1 file changed, 3 insertions(+), 8 deletions(-)

Applied on u-boot-stm/master

Thanks

>> diff --git a/board/st/stm32mp1/stm32mp1.c b/board/st/stm32mp1/stm32mp1.c
>> index 3182f44598..a0a2f9978f 100644
>> --- a/board/st/stm32mp1/stm32mp1.c
>> +++ b/board/st/stm32mp1/stm32mp1.c
>> @@ -428,14 +428,11 @@ static int board_check_usb_power(void)
>>  
>>  static void sysconf_init(void)
>>  {
>> -#ifndef CONFIG_TFABOOT
>>  	u8 *syscfg;
>> -#ifdef CONFIG_DM_REGULATOR
>>  	struct udevice *pwr_dev;
>>  	struct udevice *pwr_reg;
>>  	struct udevice *dev;
>>  	u32 otp = 0;
>> -#endif
>>  	int ret;
>>  	u32 bootr, val;
>>  
>> @@ -453,7 +450,6 @@ static void sysconf_init(void)
>>  	bootr |= (bootr & SYSCFG_BOOTR_BOOT_MASK) << SYSCFG_BOOTR_BOOTPD_SHIFT;
>>  	writel(bootr, syscfg + SYSCFG_BOOTR);
>>  
>> -#ifdef CONFIG_DM_REGULATOR
>>  	/* High Speed Low Voltage Pad mode Enable for SPI, SDMMC, ETH, QSPI
>>  	 * and TRACE. Needed above ~50MHz and conditioned by AFMUX selection.
>>  	 * The customer will have to disable this for low frequencies
>> @@ -470,7 +466,7 @@ static void sysconf_init(void)
>>  	ret = uclass_get_device_by_driver(UCLASS_PMIC,
>>  					  DM_GET_DRIVER(stm32mp_pwr_pmic),
>>  					  &pwr_dev);
>> -	if (!ret) {
>> +	if (!ret && IS_ENABLED(CONFIG_DM_REGULATOR)) {
>>  		ret = uclass_get_device_by_driver(UCLASS_MISC,
>>  						  DM_GET_DRIVER(stm32mp_bsec),
>>  						  &dev);
>> @@ -507,7 +503,6 @@ static void sysconf_init(void)
>>  			debug("VDD unknown");
>>  		}
>>  	}
>> -#endif
>>  
>>  	/* activate automatic I/O compensation
>>  	 * warning: need to ensure CSI enabled and ready in clock driver
>> @@ -524,7 +519,6 @@ static void sysconf_init(void)
>>  	}
>>  
>>  	clrbits_le32(syscfg + SYSCFG_CMPCR, SYSCFG_CMPCR_SW_CTRL);
>> -#endif
>>  }
>>  
>>  #ifdef CONFIG_DM_REGULATOR
>> @@ -647,7 +641,8 @@ int board_init(void)
>>  	regulators_enable_boot_on(_DEBUG);
>>  #endif
>>  
>> -	sysconf_init();
>> +	if (!IS_ENABLED(CONFIG_TFABOOT))
>> +		sysconf_init();
>>  
>>  	if (CONFIG_IS_ENABLED(LED))
>>  		led_default_state();
> Reviewed-by: Patrice Chotard <patrice.chotard at st.com>
>
> Thanks
>
> Patrice
> _______________________________________________
> Uboot-stm32 mailing list
> Uboot-stm32 at st-md-mailman.stormreply.com
> https://st-md-mailman.stormreply.com/mailman/listinfo/uboot-stm32


More information about the U-Boot mailing list