[PATCH v2 09/11] arm: dts: mt7622: add sata- and asm_sel nodes
Chunfeng Yun
chunfeng.yun at mediatek.com
Wed Aug 19 10:54:28 CEST 2020
On Wed, 2020-08-19 at 10:02 +0200, Frank Wunderlich wrote:
> From: Frank Wunderlich <frank-w at public-files.de>
>
> asm_sel is for switching between sata and pcie mode
> on r64 there is GPIO90 connected to ASM1480 which
> switches RX/TX pairs to PCIe/SATA connector
> output-low means sata-controller is active
>
> Signed-off-by: Frank Wunderlich <frank-w at public-files.de>
> ---
> arch/arm/dts/mt7622-bananapi-bpi-r64.dts | 9 +++++++
> arch/arm/dts/mt7622.dtsi | 31 ++++++++++++++++++++++++
> 2 files changed, 40 insertions(+)
>
> diff --git a/arch/arm/dts/mt7622-bananapi-bpi-r64.dts b/arch/arm/dts/mt7622-bananapi-bpi-r64.dts
> index 768f15bc2c..c36ec8f8d0 100644
> --- a/arch/arm/dts/mt7622-bananapi-bpi-r64.dts
> +++ b/arch/arm/dts/mt7622-bananapi-bpi-r64.dts
> @@ -204,3 +204,12 @@
> full-duplex;
> };
> };
> +
> +&gpio {
> + /*gpio 90 for setting mode to sata*/
> + asm_sel {
> + gpio-hog;
> + gpios = <90 GPIO_ACTIVE_HIGH>;
> + output-low;
> + };
> +};
> diff --git a/arch/arm/dts/mt7622.dtsi b/arch/arm/dts/mt7622.dtsi
> index fec071643e..6b4260407e 100644
> --- a/arch/arm/dts/mt7622.dtsi
> +++ b/arch/arm/dts/mt7622.dtsi
> @@ -10,6 +10,7 @@
> #include <dt-bindings/power/mt7629-power.h>
> #include <dt-bindings/reset/mt7629-reset.h>
> #include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/phy/phy.h>
>
> / {
> compatible = "mediatek,mt7622";
> @@ -270,6 +271,36 @@
> };
> };
>
> + sata: sata at 1a200000 {
> + compatible = "mediatek,mtk-ahci";
> + reg = <0x1a200000 0x1100>;
> + resets = <&pciesys MT7622_SATA_AXI_BUS_RST>,
> + <&pciesys MT7622_SATA_PHY_SW_RST>,
> + <&pciesys MT7622_SATA_PHY_REG_RST>;
> + reset-names = "axi", "sw", "reg";
> + mediatek,phy-mode = <&pciesys>;
> + ports-implemented = <0x1>;
> + phys = <&sata_port PHY_TYPE_SATA>;
> + phy-names = "sata-phy";
> + status = "okay";
> + };
> +
> + sata_phy: sata-phy at 1a243000 {
> + compatible = "mediatek,generic-tphy-v1";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
we can use ranges with parameters if you send next version, otherwise no
change is also fine to me.
ranges=<0 0x1a243000 0x100>;
> + status = "okay";
> +
> + sata_port: sata-phy at 1a243000 {
> + reg = <0x1a243000 0x0100>;
sata_port: sata-phy at 0 {
reg = <0x0 0x0100>;
> + clocks = <&topckgen CLK_TOP_ETH_500M>;
> + clock-names = "ref";
> + #phy-cells = <1>;
> + status = "okay";
> + };
> + };
For phy part,
Reviewed-by: Chunfeng Yun <chunfeng.yun at mediatek.com>
thanks
> +
> ethsys: syscon at 1b000000 {
> compatible = "mediatek,mt7622-ethsys", "syscon";
> reg = <0x1b000000 0x1000>;
More information about the U-Boot
mailing list