[PATCH] phy: marvell: a3700: add sata comphy on lane 2 with invert option
Pali Rohár
pali at kernel.org
Mon Aug 31 13:29:16 CEST 2020
On Friday 28 August 2020 16:56:29 Andre Heider wrote:
> From: zachary <zhangzg at marvell.com>
>
> - This patch moves sata phy powerup from dedicate phy to compphy
> and adds invert option for sata powerup routine.
>
> Change-Id: I1b4e8753e2b2c14c6efa97bca2ffc7d2553d8a90
> Signed-off-by: zachary <zhangzg at marvell.com>
> Signed-off-by: Ken Ma <make at marvell.com>
> Reviewed-on: http://vgitil04.il.marvell.com:8080/53601
> Reviewed-by: Igal Liberman <igall at marvell.com>
> Tested-by: Igal Liberman <igall at marvell.com>
> [a.heider: adapt to mainline]
> Signed-off-by: Andre Heider <a.heider at gmail.com>
Tested-by: Pali Rohár <pali at kernel.org>
> ---
>
> This is based on the downstream patch:
> https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/0a5b159806baa0746b6449920e450498bc269ba7
>
> Fixes SATA on my espressobin v5.
Thanks! It really fixed SATA support on EspressoBin v5 test unit.
> drivers/phy/marvell/comphy_a3700.c | 33 +++++++++++++-----------------
> 1 file changed, 14 insertions(+), 19 deletions(-)
>
> diff --git a/drivers/phy/marvell/comphy_a3700.c b/drivers/phy/marvell/comphy_a3700.c
> index dc188c44e0..4606de6f48 100644
> --- a/drivers/phy/marvell/comphy_a3700.c
> +++ b/drivers/phy/marvell/comphy_a3700.c
> @@ -273,16 +273,23 @@ static void reg_set_indirect(u32 reg, u16 data, u16 mask)
> *
> * return: 1 if PLL locked (OK), 0 otherwise (FAIL)
> */
> -static int comphy_sata_power_up(void)
> +static int comphy_sata_power_up(u32 invert)
> {
> int ret;
> + u32 data = 0;
>
> debug_enter();
>
> /*
> - * 0. Swap SATA TX lines
> + * 0. Check the Polarity invert bits
> */
> - reg_set_indirect(vphy_sync_pattern_reg, bs_txd_inv, bs_txd_inv);
> + if (invert & PHY_POLARITY_TXD_INVERT)
> + data |= bs_txd_inv;
> +
> + if (invert & PHY_POLARITY_RXD_INVERT)
> + data |= bs_rxd_inv;
> +
> + reg_set_indirect(vphy_sync_pattern_reg, data, bs_txd_inv | bs_rxd_inv);
>
> /*
> * 1. Select 40-bit data width width
> @@ -924,22 +931,6 @@ void comphy_dedicated_phys_init(void)
> }
> }
>
> - node = fdt_node_offset_by_compatible(blob, -1,
> - "marvell,armada-3700-ahci");
> - if (node > 0) {
> - if (fdtdec_get_is_enabled(blob, node)) {
> - ret = comphy_sata_power_up();
> - if (!ret)
> - printf("Failed to initialize SATA PHY\n");
> - else
> - debug("SATA PHY init succeed\n");
> - } else {
> - debug("SATA node is disabled\n");
> - }
> - } else {
> - debug("No SATA node in DT\n");
> - }
> -
> node = fdt_node_offset_by_compatible(blob, -1,
> "marvell,armada-8k-sdhci");
> if (node <= 0) {
> @@ -1007,6 +998,10 @@ int comphy_a3700_init(struct chip_serdes_phy_config *chip_cfg,
> comphy_map->invert);
> break;
>
> + case PHY_TYPE_SATA0:
> + ret = comphy_sata_power_up(comphy_map->invert);
> + break;
> +
> default:
> debug("Unknown SerDes type, skip initialize SerDes %d\n",
> lane);
> --
> 2.28.0
>
More information about the U-Boot
mailing list