[PATCH v6] ARM: dts: stm32: add seeed studio odyssey-stm32mp157c board
Marcin Sloniewski
marcin.sloniewski at gmail.com
Wed Jul 8 19:56:22 CEST 2020
This commit adds device tree files supporting
SBC from Seeed Studio based on STM32MP157C.
This works with generic stm32mp1 config.
Right now only booting from SD card is supported.
Signed-off-by: Marcin Sloniewski <marcin.sloniewski at gmail.com>
---
Changes in v6:
- forgot to add changes in v5 ;(
Changes in v5:
- removed description of PLL1 which is now handled by OPP info
- removed cd-gpio for sdmmc1 since it is not yet supported
Changes in v4:
- removed unnecessary pull up on uart4 rx
Changes in v3:
- changed name of dts files from odyssey-stm32mp157c...
to stm32mp157c-odyssey...
- removed usbotg node config
- add new board in dts/Makefile in alphabetical order
Changes in v2:
- removed `st,adc_usb_pd` from config since that
adc connection is non-existent which caused
warning or hang during boot
arch/arm/dts/Makefile | 1 +
.../dts/stm32mp157c-odyssey-som-u-boot.dtsi | 125 ++++++
arch/arm/dts/stm32mp157c-odyssey-som.dtsi | 364 ++++++++++++++++++
arch/arm/dts/stm32mp157c-odyssey-u-boot.dtsi | 58 +++
arch/arm/dts/stm32mp157c-odyssey.dts | 161 ++++++++
5 files changed, 709 insertions(+)
create mode 100644 arch/arm/dts/stm32mp157c-odyssey-som-u-boot.dtsi
create mode 100644 arch/arm/dts/stm32mp157c-odyssey-som.dtsi
create mode 100644 arch/arm/dts/stm32mp157c-odyssey-u-boot.dtsi
create mode 100644 arch/arm/dts/stm32mp157c-odyssey.dts
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index d345e30f35..d9629aba7d 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -931,6 +931,7 @@ dtb-$(CONFIG_STM32MP15x) += \
stm32mp157c-dk2.dtb \
stm32mp157c-ed1.dtb \
stm32mp157c-ev1.dtb \
+ stm32mp157c-odyssey.dtb \
stm32mp15xx-dhcom-pdk2.dtb \
stm32mp15xx-dhcor-avenger96.dtb
diff --git a/arch/arm/dts/stm32mp157c-odyssey-som-u-boot.dtsi b/arch/arm/dts/stm32mp157c-odyssey-som-u-boot.dtsi
new file mode 100644
index 0000000000..6be728846e
--- /dev/null
+++ b/arch/arm/dts/stm32mp157c-odyssey-som-u-boot.dtsi
@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski at gmail.com>
+ */
+
+#include <dt-bindings/clock/stm32mp1-clksrc.h>
+#include "stm32mp15-u-boot.dtsi"
+#include "stm32mp15-ddr3-1x4Gb-1066-binG.dtsi"
+
+/ {
+ config {
+ u-boot,boot-led = "heartbeat";
+ };
+};
+
+&clk_hse {
+ st,digbypass;
+};
+
+&i2c2 {
+ u-boot,dm-pre-reloc;
+};
+
+&i2c2_pins_a {
+ u-boot,dm-pre-reloc;
+ pins {
+ u-boot,dm-pre-reloc;
+ };
+};
+
+&pmic {
+ u-boot,dm-pre-reloc;
+};
+
+&rcc {
+ st,clksrc = <
+ CLK_MPU_PLL1P
+ CLK_AXI_PLL2P
+ CLK_MCU_PLL3P
+ CLK_PLL12_HSE
+ CLK_PLL3_HSE
+ CLK_PLL4_HSE
+ CLK_RTC_LSE
+ CLK_MCO1_DISABLED
+ CLK_MCO2_DISABLED
+ >;
+
+ st,clkdiv = <
+ 1 /*MPU*/
+ 0 /*AXI*/
+ 0 /*MCU*/
+ 1 /*APB1*/
+ 1 /*APB2*/
+ 1 /*APB3*/
+ 1 /*APB4*/
+ 2 /*APB5*/
+ 23 /*RTC*/
+ 0 /*MCO1*/
+ 0 /*MCO2*/
+ >;
+
+ st,pkcs = <
+ CLK_CKPER_HSE
+ CLK_FMC_ACLK
+ CLK_QSPI_ACLK
+ CLK_ETH_DISABLED
+ CLK_SDMMC12_PLL4P
+ CLK_DSI_DSIPLL
+ CLK_STGEN_HSE
+ CLK_USBPHY_HSE
+ CLK_SPI2S1_PLL3Q
+ CLK_SPI2S23_PLL3Q
+ CLK_SPI45_HSI
+ CLK_SPI6_HSI
+ CLK_I2C46_HSI
+ CLK_SDMMC3_PLL4P
+ CLK_USBO_USBPHY
+ CLK_ADC_CKPER
+ CLK_CEC_LSE
+ CLK_I2C12_HSI
+ CLK_I2C35_HSI
+ CLK_UART1_HSI
+ CLK_UART24_HSI
+ CLK_UART35_HSI
+ CLK_UART6_HSI
+ CLK_UART78_HSI
+ CLK_SPDIF_PLL4P
+ CLK_FDCAN_PLL4R
+ CLK_SAI1_PLL3Q
+ CLK_SAI2_PLL3Q
+ CLK_SAI3_PLL3Q
+ CLK_SAI4_PLL3Q
+ CLK_RNG1_LSI
+ CLK_RNG2_LSI
+ CLK_LPTIM1_PCLK1
+ CLK_LPTIM23_PCLK3
+ CLK_LPTIM45_LSE
+ >;
+
+ /* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
+ pll2: st,pll at 1 {
+ compatible = "st,stm32mp1-pll";
+ reg = <1>;
+ cfg = < 2 65 1 0 0 PQR(1,1,1) >;
+ frac = < 0x1400 >;
+ u-boot,dm-pre-reloc;
+ };
+
+ /* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
+ pll3: st,pll at 2 {
+ compatible = "st,stm32mp1-pll";
+ reg = <2>;
+ cfg = < 1 33 1 16 36 PQR(1,1,1) >;
+ frac = < 0x1a04 >;
+ u-boot,dm-pre-reloc;
+ };
+
+ /* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
+ pll4: st,pll at 3 {
+ compatible = "st,stm32mp1-pll";
+ reg = <3>;
+ cfg = < 3 98 5 7 7 PQR(1,1,1) >;
+ u-boot,dm-pre-reloc;
+ };
+};
diff --git a/arch/arm/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/dts/stm32mp157c-odyssey-som.dtsi
new file mode 100644
index 0000000000..855de9523c
--- /dev/null
+++ b/arch/arm/dts/stm32mp157c-odyssey-som.dtsi
@@ -0,0 +1,364 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski at gmail.com>
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+
+ model = "Seeed Studio Odyssey-STM32MP157C SOM";
+ compatible = "seeed,odyssey-stm32mp157c-som", "st,stm32mp157";
+
+ memory at c0000000 {
+ device_type = "memory";
+ reg = <0xc0000000 0x20000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mcuram2: mcuram2 at 10000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10000000 0x40000>;
+ no-map;
+ };
+
+ vdev0vring0: vdev0vring0 at 10040000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10040000 0x1000>;
+ no-map;
+ };
+
+ vdev0vring1: vdev0vring1 at 10041000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10041000 0x1000>;
+ no-map;
+ };
+
+ vdev0buffer: vdev0buffer at 10042000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10042000 0x4000>;
+ no-map;
+ };
+
+ mcuram: mcuram at 30000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x30000000 0x40000>;
+ no-map;
+ };
+
+ retram: retram at 38000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x38000000 0x10000>;
+ no-map;
+ };
+
+ gpu_reserved: gpu at d4000000 {
+ reg = <0xd4000000 0x4000000>;
+ no-map;
+ };
+
+ optee at de000000 {
+ reg = <0xde000000 0x02000000>;
+ no-map;
+ };
+ };
+
+ led {
+ compatible = "gpio-leds";
+ blue {
+ label = "heartbeat";
+ gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+ };
+
+};
+
+&gpu {
+ contiguous-area = <&gpu_reserved>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c2_pins_a>;
+ pinctrl-1 = <&i2c2_pins_sleep_a>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ clock-frequency = <400000>;
+ status = "okay";
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ pmic: stpmic at 33 {
+ compatible = "st,stpmic1";
+ reg = <0x33>;
+ interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ status = "okay";
+
+ regulators {
+ compatible = "st,stpmic1-regulators";
+ ldo1-supply = <&v3v3>;
+ ldo3-supply = <&vdd_ddr>;
+ ldo6-supply = <&v3v3>;
+ pwr_sw1-supply = <&bst_out>;
+ pwr_sw2-supply = <&bst_out>;
+
+ vddcore: buck1 {
+ regulator-name = "vddcore";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd_ddr: buck2 {
+ regulator-name = "vdd_ddr";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd: buck3 {
+ regulator-name = "vdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ st,mask-reset;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ v3v3: buck4 {
+ regulator-name = "v3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ regulator-initial-mode = <0>;
+ };
+
+ v1v8_audio: ldo1 {
+ regulator-name = "v1v8_audio";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO1 0>;
+ };
+
+ v3v3_hdmi: ldo2 {
+ regulator-name = "v3v3_hdmi";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO2 0>;
+ };
+
+ vtt_ddr: ldo3 {
+ regulator-name = "vtt_ddr";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <750000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ vdd_usb: ldo4 {
+ regulator-name = "vdd_usb";
+ interrupts = <IT_CURLIM_LDO4 0>;
+ };
+
+ vdda: ldo5 {
+ regulator-name = "vdda";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ interrupts = <IT_CURLIM_LDO5 0>;
+ regulator-boot-on;
+ };
+
+ v1v2_hdmi: ldo6 {
+ regulator-name = "v1v2_hdmi";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO6 0>;
+ };
+
+ vref_ddr: vref_ddr {
+ regulator-name = "vref_ddr";
+ regulator-always-on;
+ };
+
+ bst_out: boost {
+ regulator-name = "bst_out";
+ interrupts = <IT_OCP_BOOST 0>;
+ };
+
+ vbus_otg: pwr_sw1 {
+ regulator-name = "vbus_otg";
+ interrupts = <IT_OCP_OTG 0>;
+ };
+
+ vbus_sw: pwr_sw2 {
+ regulator-name = "vbus_sw";
+ interrupts = <IT_OCP_SWOUT 0>;
+ regulator-active-discharge = <1>;
+ };
+ };
+
+ onkey {
+ compatible = "st,stpmic1-onkey";
+ interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+ interrupt-names = "onkey-falling", "onkey-rising";
+ power-off-time-sec = <10>;
+ status = "okay";
+ };
+
+ watchdog {
+ compatible = "st,stpmic1-wdt";
+ status = "disabled";
+ };
+ };
+};
+
+&ipcc {
+ status = "okay";
+};
+
+&iwdg2 {
+ timeout-sec = <32>;
+ status = "okay";
+};
+
+&m4_rproc {
+ memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+ <&vdev0vring1>, <&vdev0buffer>;
+ mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+ mbox-names = "vq0", "vq1", "shutdown";
+ interrupt-parent = <&exti>;
+ interrupts = <68 1>;
+ status = "okay";
+};
+
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
+ broken-cd;
+ disable-wp;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ status = "okay";
+};
+
+&timers1 {
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "disabled";
+ pwm {
+ pinctrl-0 = <&pwm1_pins_a>;
+ pinctrl-1 = <&pwm1_sleep_pins_a>;
+ pinctrl-names = "default", "sleep";
+ status = "okay";
+ };
+ timer at 0 {
+ status = "okay";
+ };
+};
+
+&timers3 {
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "disabled";
+ pwm {
+ pinctrl-0 = <&pwm3_pins_a>;
+ pinctrl-1 = <&pwm3_sleep_pins_a>;
+ pinctrl-names = "default", "sleep";
+ status = "okay";
+ };
+ timer at 2 {
+ status = "okay";
+ };
+};
+
+&timers4 {
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "disabled";
+ pwm {
+ pinctrl-0 = <&pwm4_pins_a &pwm4_pins_b>;
+ pinctrl-1 = <&pwm4_sleep_pins_a &pwm4_sleep_pins_b>;
+ pinctrl-names = "default", "sleep";
+ status = "okay";
+ };
+ timer at 3 {
+ status = "okay";
+ };
+};
+
+&timers5 {
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "disabled";
+ pwm {
+ pinctrl-0 = <&pwm5_pins_a>;
+ pinctrl-1 = <&pwm5_sleep_pins_a>;
+ pinctrl-names = "default", "sleep";
+ status = "okay";
+ };
+ timer at 4 {
+ status = "okay";
+ };
+};
+
+&timers6 {
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "disabled";
+ timer at 5 {
+ status = "okay";
+ };
+};
+
+&timers12 {
+ /delete-property/dmas;
+ /delete-property/dma-names;
+ status = "disabled";
+ pwm {
+ pinctrl-0 = <&pwm12_pins_a>;
+ pinctrl-1 = <&pwm12_sleep_pins_a>;
+ pinctrl-names = "default", "sleep";
+ status = "okay";
+ };
+ timer at 11 {
+ status = "okay";
+ };
+};
+
+&vrefbuf {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ vdda-supply = <&vdd>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/stm32mp157c-odyssey-u-boot.dtsi b/arch/arm/dts/stm32mp157c-odyssey-u-boot.dtsi
new file mode 100644
index 0000000000..abceba5cbd
--- /dev/null
+++ b/arch/arm/dts/stm32mp157c-odyssey-u-boot.dtsi
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski at gmail.com>
+ */
+
+ #include "stm32mp157c-odyssey-som-u-boot.dtsi"
+
+/ {
+ aliases {
+ mmc0 = &sdmmc1;
+ usb0 = &usbotg_hs;
+ };
+ config {
+ u-boot,boot-led = "heartbeat";
+ u-boot,error-led = "error";
+ };
+ led {
+ red {
+ label = "error";
+ gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ status = "okay";
+ };
+ };
+};
+
+&adc {
+ status = "okay";
+};
+
+&sdmmc1 {
+ u-boot,dm-spl;
+};
+
+&sdmmc1_b4_pins_a {
+ u-boot,dm-spl;
+ pins1 {
+ u-boot,dm-spl;
+ };
+ pins2 {
+ u-boot,dm-spl;
+ };
+};
+
+&uart4 {
+ u-boot,dm-pre-reloc;
+};
+
+&uart4_pins_a {
+ u-boot,dm-pre-reloc;
+ pins1 {
+ u-boot,dm-pre-reloc;
+ };
+ pins2 {
+ u-boot,dm-pre-reloc;
+ };
+};
+
diff --git a/arch/arm/dts/stm32mp157c-odyssey.dts b/arch/arm/dts/stm32mp157c-odyssey.dts
new file mode 100644
index 0000000000..587a94f555
--- /dev/null
+++ b/arch/arm/dts/stm32mp157c-odyssey.dts
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski at gmail.com>
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c-odyssey-som.dtsi"
+
+/ {
+
+ model = "Seeed Studio Odyssey-STM32MP157C Board";
+ compatible = "seeed,odyssey-stm32mp157c", "st,stm32mp157";
+
+ aliases {
+ ethernet0 = ðernet0;
+ serial0 = &uart4;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ led {
+ compatible = "gpio-leds";
+ blue {
+ label = "heartbeat";
+ gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+ };
+
+};
+
+&adc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&adc12_ain_pins_a>, <&adc12_usb_cc_pins_a>;
+ vdd-supply = <&vdd>;
+ vdda-supply = <&vdd>;
+ vref-supply = <&vrefbuf>;
+ status = "disabled";
+ adc1: adc at 0 {
+ /*
+ * Type-C USB_PWR_CC1 & USB_PWR_CC2 on in18 & in19.
+ * Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C:
+ * 5 * (56 + 47kOhms) * 5pF => 2.5us.
+ * Use arbitrary margin here (e.g. 5us).
+ */
+ st,min-sample-time-nsecs = <5000>;
+ /* AIN connector, USB Type-C CC1 & CC2 */
+ st,adc-channels = <0 1 6 13 18 19>;
+ status = "okay";
+ };
+ adc2: adc at 100 {
+ /* AIN connector, USB Type-C CC1 & CC2 */
+ st,adc-channels = <0 1 2 6 18 19>;
+ st,min-sample-time-nsecs = <5000>;
+ status = "okay";
+ };
+};
+
+&cec {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&cec_pins_b>;
+ pinctrl-1 = <&cec_pins_sleep_b>;
+ status = "okay";
+};
+
+ðernet0 {
+ status = "okay";
+ pinctrl-0 = <ðernet0_rgmii_pins_a>;
+ pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rgmii-id";
+ max-speed = <1000>;
+ phy-handle = <&phy0>;
+
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ };
+ };
+};
+
+&gpu {
+ contiguous-area = <&gpu_reserved>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c1_pins_a>;
+ pinctrl-1 = <&i2c1_pins_sleep_a>;
+ i2c-scl-rising-time-ns = <100>;
+ i2c-scl-falling-time-ns = <7>;
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+};
+
+&i2s2 {
+ clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+ clock-names = "pclk", "i2sclk", "x8k", "x11k";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2s2_pins_a>;
+ pinctrl-1 = <&i2s2_pins_sleep_a>;
+ status = "okay";
+};
+
+&pwr_regulators {
+ vdd-supply = <&vdd>;
+ vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+ broken-cd;
+ disable-wp;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_a>;
+ status = "okay";
+};
+
+&usbh_ehci {
+ phys = <&usbphyc_port0>;
+ status = "okay";
+};
+
+&usbotg_hs {
+ dr_mode = "peripheral";
+ phys = <&usbphyc_port1 0>;
+ phy-names = "usb2-phy";
+ status = "okay";
+};
+
+&usbphyc {
+ status = "okay";
+};
+
+&usbphyc_port0 {
+ phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+ phy-supply = <&vdd_usb>;
+};
+
--
2.26.2
More information about the U-Boot
mailing list