[PATCHv2 01/36] dm: spi: Convert Freescale ESPI driver to driver model

Z.q. Hou zhiqiang.hou at nxp.com
Thu Jun 4 04:40:38 CEST 2020


Hi Jagan,

Thanks for your comments!

> -----Original Message-----
> From: Jagan Teki [mailto:jagan at amarulasolutions.com]
> Sent: 2020年6月3日 15:41
> To: Z.q. Hou <zhiqiang.hou at nxp.com>
> Cc: U-Boot-Denx <u-boot at lists.denx.de>; Priyanka Jain
> <priyanka.jain at nxp.com>; Shengzhou Liu <shengzhou.liu at nxp.com>; Simon
> Glass <sjg at chromium.org>; Biwen Li <biwen.li at nxp.com>; Bin Meng
> <bmeng.cn at gmail.com>; Jiafei Pan <jiafei.pan at nxp.com>; Chuanhua Han
> <chuanhua.han at nxp.com>; Xiaowei Bao <xiaowei.bao at nxp.com>
> Subject: Re: [PATCHv2 01/36] dm: spi: Convert Freescale ESPI driver to driver
> model
> 
> On Wed, Jun 3, 2020 at 7:33 AM Z.q. Hou <zhiqiang.hou at nxp.com> wrote:
> >
> > Hi Jagan,
> >
> > Thanks a lot for your comments!
> >
> > > -----Original Message-----
> > > From: Jagan Teki <jagan at amarulasolutions.com>
> > > Sent: 2020年6月3日 3:29
> > > To: Z.q. Hou <zhiqiang.hou at nxp.com>
> > > Cc: U-Boot-Denx <u-boot at lists.denx.de>; Priyanka Jain
> > > <priyanka.jain at nxp.com>; Shengzhou Liu <shengzhou.liu at nxp.com>;
> > > Simon Glass <sjg at chromium.org>; Biwen Li <biwen.li at nxp.com>; Bin
> > > Meng <bmeng.cn at gmail.com>; Jiafei Pan <jiafei.pan at nxp.com>;
> Chuanhua
> > > Han <chuanhua.han at nxp.com>; Xiaowei Bao <xiaowei.bao at nxp.com>
> > > Subject: Re: [PATCHv2 01/36] dm: spi: Convert Freescale ESPI driver
> > > to driver model
> > >
> > > On Tue, Jun 2, 2020 at 7:10 PM Zhiqiang Hou <Zhiqiang.Hou at nxp.com>
> > > wrote:
> > > >
> > > > From: Chuanhua Han <chuanhua.han at nxp.com>
> > > >
> > > > Modify the Freescale ESPI driver to support the driver model.
> > > > Also resolved the following problems:
> > > >
> > > > ===================== WARNING ====================== This
> > > board does
> > > > not use CONFIG_DM_SPI. Please update the board before v2019.04 for
> > > > no dm conversion and v2019.07 for partially dm converted drivers.
> > > > Failure to update can lead to driver/board removal See
> > > > doc/driver-model/MIGRATION.txt for more info.
> > > > ====================================================
> > > > ===================== WARNING ====================== This
> > > board does
> > > > not use CONFIG_DM_SPI_FLASH. Please update the board to use
> > > > CONFIG_SPI_FLASH before the v2019.07 release.
> > > > Failure to update by the deadline may result in board removal.
> > > > See doc/driver-model/MIGRATION.txt for more info.
> > > > ====================================================
> > > >
> > > > Signed-off-by: Chuanhua Han <chuanhua.han at nxp.com>
> > > > Signed-off-by: Xiaowei Bao <xiaowei.bao at nxp.com>
> > > > Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou at nxp.com>
> > > > ---
> > > > V2:
> > > >  - Rebase the patch, no change intended.
> > > >
> > > >  drivers/spi/fsl_espi.c              | 444
> > > ++++++++++++++++++++--------
> > > >  include/dm/platform_data/fsl_espi.h |  16 +
> > > >  2 files changed, 337 insertions(+), 123 deletions(-)  create mode
> > > > 100644 include/dm/platform_data/fsl_espi.h
> > > >
> > > > diff --git a/drivers/spi/fsl_espi.c b/drivers/spi/fsl_espi.c index
> > > > 50d194f614..5c76fd962e 100644
> > > > --- a/drivers/spi/fsl_espi.c
> > > > +++ b/drivers/spi/fsl_espi.c
> > > > @@ -3,7 +3,9 @@
> > > >   * eSPI controller driver.
> > > >   *
> > > >   * Copyright 2010-2011 Freescale Semiconductor, Inc.
> > > > + * Copyright 2020 NXP
> > > >   * Author: Mingkai Hu (Mingkai.hu at freescale.com)
> > > > + *        Chuanhua Han (chuanhua.han at nxp.com)
> > > >   */
> > > >
> > > >  #include <common.h>
> > > > @@ -14,10 +16,16 @@
> > > >  #include <malloc.h>
> > > >  #include <spi.h>
> > > >  #include <asm/immap_85xx.h>
> > > > +#include <dm.h>
> > > > +#include <errno.h>
> > > > +#include <fdtdec.h>
> > > > +#include <dm/platform_data/fsl_espi.h>
> > > >
> > > >  struct fsl_spi_slave {
> > > >         struct spi_slave slave;
> > > >         ccsr_espi_t     *espi;
> > > > +       u32             speed_hz;
> > > > +       unsigned int    cs;
> > > >         unsigned int    div16;
> > > >         unsigned int    pm;
> > > >         int             tx_timeout;
> > > > @@ -31,6 +39,9 @@ struct fsl_spi_slave {  #define
> > > > to_fsl_spi_slave(s) container_of(s, struct fsl_spi_slave, slave)
> > > >  #define US_PER_SECOND          1000000UL
> > > >
> > > > +/* default SCK frequency, unit: HZ */
> > > > +#define FSL_ESPI_DEFAULT_SCK_FREQ   10000000
> > > > +
> > > >  #define ESPI_MAX_CS_NUM                4
> > > >  #define ESPI_FIFO_WIDTH_BIT    32
> > > >
> > > > @@ -65,116 +76,27 @@ struct fsl_spi_slave {
> > > >
> > > >  #define ESPI_MAX_DATA_TRANSFER_LEN 0xFFF0
> > > >
> > > > -struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
> > > > -               unsigned int max_hz, unsigned int mode)
> > > > -{
> > > > -       struct fsl_spi_slave *fsl;
> > > > -       sys_info_t sysinfo;
> > > > -       unsigned long spibrg = 0;
> > > > -       unsigned long spi_freq = 0;
> > > > -       unsigned char pm = 0;
> > > > -
> > > > -       if (!spi_cs_is_valid(bus, cs))
> > > > -               return NULL;
> > > > -
> > > > -       fsl = spi_alloc_slave(struct fsl_spi_slave, bus, cs);
> > > > -       if (!fsl)
> > > > -               return NULL;
> > > > -
> > > > -       fsl->espi = (void *)(CONFIG_SYS_MPC85xx_ESPI_ADDR);
> > > > -       fsl->mode = mode;
> > > > -       fsl->max_transfer_length = ESPI_MAX_DATA_TRANSFER_LEN;
> > > > -
> > > > -       /* Set eSPI BRG clock source */
> > > > -       get_sys_info(&sysinfo);
> > > > -       spibrg = sysinfo.freq_systembus / 2;
> > > > -       fsl->div16 = 0;
> > > > -       if ((spibrg / max_hz) > 32) {
> > > > -               fsl->div16 = ESPI_CSMODE_DIV16;
> > > > -               pm = spibrg / (max_hz * 16 * 2);
> > > > -               if (pm > 16) {
> > > > -                       pm = 16;
> > > > -                       debug("Requested speed is too low: %d
> > > Hz, %ld Hz "
> > > > -                               "is used.\n", max_hz, spibrg / (32
> *
> > > 16));
> > > > -               }
> > > > -       } else
> > > > -               pm = spibrg / (max_hz * 2);
> > > > -       if (pm)
> > > > -               pm--;
> > > > -       fsl->pm = pm;
> > > > -
> > > > -       if (fsl->div16)
> > > > -               spi_freq = spibrg / ((pm + 1) * 2 * 16);
> > > > -       else
> > > > -               spi_freq = spibrg / ((pm + 1) * 2);
> > > > -
> > > > -       /* set tx_timeout to 10 times of one espi FIFO entry go out */
> > > > -       fsl->tx_timeout = DIV_ROUND_UP((US_PER_SECOND *
> > > ESPI_FIFO_WIDTH_BIT
> > > > -                               * 10), spi_freq);
> > > > -
> > > > -       return &fsl->slave;
> > > > -}
> > > > -
> > > > -void spi_free_slave(struct spi_slave *slave) -{
> > > > -       struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
> > > > -       free(fsl);
> > > > -}
> > > > -
> > > > -int spi_claim_bus(struct spi_slave *slave)
> > > > +void fsl_spi_cs_activate(struct spi_slave *slave, uint cs)
> > > >  {
> > > >         struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
> > > >         ccsr_espi_t *espi = fsl->espi;
> > > > -       unsigned char pm = fsl->pm;
> > > > -       unsigned int cs = slave->cs;
> > > > -       unsigned int mode =  fsl->mode;
> > > > -       unsigned int div16 = fsl->div16;
> > > > -       int i;
> > > > -
> > > > -       debug("%s: bus:%i cs:%i\n", __func__, slave->bus, cs);
> > > > -
> > > > -       /* Enable eSPI interface */
> > > > -       out_be32(&espi->mode, ESPI_MODE_RXTHR(3)
> > > > -                       | ESPI_MODE_TXTHR(4) |
> ESPI_MODE_EN);
> > > > -
> > > > -       out_be32(&espi->event, 0xffffffff); /* Clear all eSPI events */
> > > > -       out_be32(&espi->mask, 0x00000000); /* Mask  all eSPI
> > > interrupts */
> > > > -
> > > > -       /* Init CS mode interface */
> > > > -       for (i = 0; i < ESPI_MAX_CS_NUM; i++)
> > > > -               out_be32(&espi->csmode[i],
> ESPI_CSMODE_INIT_VAL);
> > > > -
> > > > -       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs]) &
> > > > -               ~(ESPI_CSMODE_PM(0xF) | ESPI_CSMODE_DIV16
> > > > -               | ESPI_CSMODE_CI_INACTIVEHIGH |
> > > ESPI_CSMODE_CP_BEGIN_EDGCLK
> > > > -               | ESPI_CSMODE_REV_MSB_FIRST |
> > > ESPI_CSMODE_LEN(0xF)));
> > > > -
> > > > -       /* Set eSPI BRG clock source */
> > > > -       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
> > > > -               | ESPI_CSMODE_PM(pm) | div16);
> > > > -
> > > > -       /* Set eSPI mode */
> > > > -       if (mode & SPI_CPHA)
> > > > -               out_be32(&espi->csmode[cs],
> > > in_be32(&espi->csmode[cs])
> > > > -                       | ESPI_CSMODE_CP_BEGIN_EDGCLK);
> > > > -       if (mode & SPI_CPOL)
> > > > -               out_be32(&espi->csmode[cs],
> > > in_be32(&espi->csmode[cs])
> > > > -                       | ESPI_CSMODE_CI_INACTIVEHIGH);
> > > > -
> > > > -       /* Character bit order: msb first */
> > > > -       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
> > > > -               | ESPI_CSMODE_REV_MSB_FIRST);
> > > > -
> > > > -       /* Character length in bits, between 0x3~0xf, i.e. 4bits~16bits
> */
> > > > -       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
> > > > -               | ESPI_CSMODE_LEN(7));
> > > > +       unsigned int com = 0;
> > > > +       size_t data_len = fsl->data_len;
> > > >
> > > > -       return 0;
> > > > +       com &= ~(ESPI_COM_CS(0x3) |
> ESPI_COM_TRANLEN(0xFFFF));
> > > > +       com |= ESPI_COM_CS(cs);
> > > > +       com |= ESPI_COM_TRANLEN(data_len - 1);
> > > > +       out_be32(&espi->com, com);
> > > >  }
> > > >
> > > > -void spi_release_bus(struct spi_slave *slave)
> > > > +void fsl_spi_cs_deactivate(struct spi_slave *slave)
> > > >  {
> > > > +       struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
> > > > +       ccsr_espi_t *espi = fsl->espi;
> > > >
> > > > +       /* clear the RXCNT and TXCNT */
> > > > +       out_be32(&espi->mode, in_be32(&espi->mode) &
> > > (~ESPI_MODE_EN));
> > > > +       out_be32(&espi->mode, in_be32(&espi->mode) |
> > > ESPI_MODE_EN);
> > > >  }
> > > >
> > > >  static void fsl_espi_tx(struct fsl_spi_slave *fsl, const void
> > > > *dout) @@ -207,7 +129,8 @@ static void fsl_espi_tx(struct
> > > > fsl_spi_slave *fsl,
> > > const void *dout)
> > > >                 debug("***spi_xfer:...Tx timeout! event = %08x\n",
> > > > event);  }
> > > >
> > > > -static int fsl_espi_rx(struct fsl_spi_slave *fsl, void *din,
> > > > unsigned int bytes)
> > > > +static int fsl_espi_rx(struct fsl_spi_slave *fsl, void *din,
> > > > +                      unsigned int bytes)
> > > >  {
> > > >         ccsr_espi_t *espi = fsl->espi;
> > > >         unsigned int tmpdin, rx_times; @@ -239,10 +162,17 @@
> > > > static int fsl_espi_rx(struct fsl_spi_slave *fsl, void *din, unsigned int
> bytes)
> > > >         return bytes;
> > > >  }
> > > >
> > > > -int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const
> > > > void
> > > *data_out,
> > > > -               void *data_in, unsigned long flags)
> > > > +void  espi_release_bus(struct fsl_spi_slave *fsl)
> > > >  {
> > > > -       struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
> > > > +       /* Disable the SPI hardware */
> > > > +        out_be32(&fsl->espi->mode,
> > > > +                 in_be32(&fsl->espi->mode) &
> (~ESPI_MODE_EN)); }
> > > > +
> > > > +int espi_xfer(struct fsl_spi_slave *fsl,  uint cs, unsigned int bitlen,
> > > > +             const void *data_out, void *data_in, unsigned long
> > > > +flags) {
> > > > +       struct spi_slave *slave = &fsl->slave;
> > > >         ccsr_espi_t *espi = fsl->espi;
> > > >         unsigned int event, rx_bytes;
> > > >         const void *dout = NULL;
> > > > @@ -261,13 +191,14 @@ int spi_xfer(struct spi_slave *slave,
> > > > unsigned int
> > > bitlen, const void *data_out,
> > > >         max_tran_len = fsl->max_transfer_length;
> > > >         switch (flags) {
> > > >         case SPI_XFER_BEGIN:
> > > > -               cmd_len = fsl->cmd_len = data_len;
> > > > +               cmd_len = data_len;
> > > > +               fsl->cmd_len = cmd_len;
> > > >                 memcpy(cmd_buf, data_out, cmd_len);
> > > >                 return 0;
> > > >         case 0:
> > > >         case SPI_XFER_END:
> > > >                 if (bitlen == 0) {
> > > > -                       spi_cs_deactivate(slave);
> > > > +                       fsl_spi_cs_deactivate(slave);
> > > >                         return 0;
> > > >                 }
> > > >                 buf_len = 2 * cmd_len + min(data_len,
> > > > (size_t)max_tran_len); @@ -307,7 +238,7 @@ int spi_xfer(struct
> > > > spi_slave
> > > *slave, unsigned int bitlen, const void *data_out,
> > > >                 num_blks = DIV_ROUND_UP(tran_len + cmd_len,
> 4);
> > > >                 num_bytes = (tran_len + cmd_len) % 4;
> > > >                 fsl->data_len = tran_len + cmd_len;
> > > > -               spi_cs_activate(slave);
> > > > +               fsl_spi_cs_activate(slave, cs);
> > > >
> > > >                 /* Clear all eSPI events */
> > > >                 out_be32(&espi->event , 0xffffffff); @@ -350,37
> > > > +281,304 @@ int spi_xfer(struct spi_slave *slave, unsigned int
> > > > +bitlen, const
> > > void *data_out,
> > > >                                 *(int *)buffer += tran_len;
> > > >                         }
> > > >                 }
> > > > -               spi_cs_deactivate(slave);
> > > > +               fsl_spi_cs_deactivate(slave);
> > > >         }
> > > >
> > > >         free(buffer);
> > > >         return 0;
> > > >  }
> > > >
> > > > +void espi_claim_bus(struct fsl_spi_slave *fsl, unsigned int cs) {
> > > > +       ccsr_espi_t *espi = fsl->espi;
> > > > +       unsigned char pm = fsl->pm;
> > > > +       unsigned int mode =  fsl->mode;
> > > > +       unsigned int div16 = fsl->div16;
> > > > +       int i;
> > > > +
> > > > +       /* Enable eSPI interface */
> > > > +       out_be32(&espi->mode, ESPI_MODE_RXTHR(3)
> > > > +                       | ESPI_MODE_TXTHR(4) |
> ESPI_MODE_EN);
> > > > +
> > > > +       out_be32(&espi->event, 0xffffffff); /* Clear all eSPI events */
> > > > +       out_be32(&espi->mask, 0x00000000); /* Mask  all eSPI
> > > > + interrupts */
> > > > +
> > > > +       /* Init CS mode interface */
> > > > +       for (i = 0; i < ESPI_MAX_CS_NUM; i++)
> > > > +               out_be32(&espi->csmode[i],
> > > ESPI_CSMODE_INIT_VAL);
> > > > +
> > > > +       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs]) &
> > > > +               ~(ESPI_CSMODE_PM(0xF) | ESPI_CSMODE_DIV16
> > > > +               | ESPI_CSMODE_CI_INACTIVEHIGH |
> > > ESPI_CSMODE_CP_BEGIN_EDGCLK
> > > > +               | ESPI_CSMODE_REV_MSB_FIRST |
> > > ESPI_CSMODE_LEN(0xF)));
> > > > +
> > > > +       /* Set eSPI BRG clock source */
> > > > +       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
> > > > +               | ESPI_CSMODE_PM(pm) | div16);
> > > > +
> > > > +       /* Set eSPI mode */
> > > > +       if (mode & SPI_CPHA)
> > > > +               out_be32(&espi->csmode[cs],
> > > in_be32(&espi->csmode[cs])
> > > > +                       | ESPI_CSMODE_CP_BEGIN_EDGCLK);
> > > > +       if (mode & SPI_CPOL)
> > > > +               out_be32(&espi->csmode[cs],
> > > in_be32(&espi->csmode[cs])
> > > > +                       | ESPI_CSMODE_CI_INACTIVEHIGH);
> > > > +
> > > > +       /* Character bit order: msb first */
> > > > +       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
> > > > +               | ESPI_CSMODE_REV_MSB_FIRST);
> > > > +
> > > > +       /* Character length in bits, between 0x3~0xf, i.e. 4bits~16bits
> */
> > > > +       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
> > > > +               | ESPI_CSMODE_LEN(7)); }
> > > > +
> > > > +void espi_setup_slave(struct fsl_spi_slave *fsl) {
> > > > +       unsigned int max_hz;
> > > > +       sys_info_t sysinfo;
> > > > +       unsigned long spibrg = 0;
> > > > +       unsigned long spi_freq = 0;
> > > > +       unsigned char pm = 0;
> > > > +
> > > > +       max_hz = fsl->speed_hz;
> > > > +
> > > > +       get_sys_info(&sysinfo);
> > > > +       spibrg = sysinfo.freq_systembus / 2;
> > > > +       fsl->div16 = 0;
> > > > +       if ((spibrg / max_hz) > 32) {
> > > > +               fsl->div16 = ESPI_CSMODE_DIV16;
> > > > +               pm = spibrg / (max_hz * 16 * 2);
> > > > +               if (pm > 16) {
> > > > +                       pm = 16;
> > > > +                       debug("max_hz is too low: %d Hz, %ld Hz
> is
> > > used.\n",
> > > > +                             max_hz, spibrg / (32 * 16));
> > > > +               }
> > > > +       } else {
> > > > +               pm = spibrg / (max_hz * 2);
> > > > +       }
> > > > +       if (pm)
> > > > +               pm--;
> > > > +       fsl->pm = pm;
> > > > +
> > > > +       if (fsl->div16)
> > > > +               spi_freq = spibrg / ((pm + 1) * 2 * 16);
> > > > +       else
> > > > +               spi_freq = spibrg / ((pm + 1) * 2);
> > > > +
> > > > +       /* set tx_timeout to 10 times of one espi FIFO entry go out */
> > > > +       fsl->tx_timeout = DIV_ROUND_UP((US_PER_SECOND *
> > > ESPI_FIFO_WIDTH_BIT
> > > > +                               * 10), spi_freq);/* Set eSPI BRG
> > > clock
> > > > +source */ }
> > > > +
> > > > +#if !CONFIG_IS_ENABLED(DM_SPI)
> > > >  int spi_cs_is_valid(unsigned int bus, unsigned int cs)  {
> > > >         return bus == 0 && cs < ESPI_MAX_CS_NUM;  }
> > > >
> > > > -void spi_cs_activate(struct spi_slave *slave)
> > > > +struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
> > > > +                                 unsigned int max_hz,
> unsigned
> > > int
> > > > +mode) {
> > > > +       struct fsl_spi_slave *fsl;
> > > > +
> > > > +       if (!spi_cs_is_valid(bus, cs))
> > > > +               return NULL;
> > > > +
> > > > +       fsl = spi_alloc_slave(struct fsl_spi_slave, bus, cs);
> > > > +       if (!fsl)
> > > > +               return NULL;
> > > > +
> > > > +       fsl->espi = (void *)(CONFIG_SYS_MPC85xx_ESPI_ADDR);
> > > > +       fsl->mode = mode;
> > > > +       fsl->max_transfer_length = ESPI_MAX_DATA_TRANSFER_LEN;
> > > > +       fsl->speed_hz = max_hz;
> > > > +
> > > > +       espi_setup_slave(fsl);
> > > > +
> > > > +       return &fsl->slave;
> > > > +}
> > > > +
> > > > +void spi_free_slave(struct spi_slave *slave)
> > > >  {
> > > >         struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
> > > > -       ccsr_espi_t *espi = fsl->espi;
> > > > -       unsigned int com = 0;
> > > > -       size_t data_len = fsl->data_len;
> > > >
> > > > -       com &= ~(ESPI_COM_CS(0x3) | ESPI_COM_TRANLEN(0xFFFF));
> > > > -       com |= ESPI_COM_CS(slave->cs);
> > > > -       com |= ESPI_COM_TRANLEN(data_len - 1);
> > > > -       out_be32(&espi->com, com);
> > > > +       free(fsl);
> > > >  }
> > > >
> > > > -void spi_cs_deactivate(struct spi_slave *slave)
> > > > +int spi_claim_bus(struct spi_slave *slave)
> > > >  {
> > > >         struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
> > > > -       ccsr_espi_t *espi = fsl->espi;
> > > >
> > > > -       /* clear the RXCNT and TXCNT */
> > > > -       out_be32(&espi->mode, in_be32(&espi->mode) &
> > > (~ESPI_MODE_EN));
> > > > -       out_be32(&espi->mode, in_be32(&espi->mode) |
> > > ESPI_MODE_EN);
> > > > +       espi_claim_bus(fsl, slave->cs);
> > > > +
> > > > +       return 0;
> > > >  }
> > > > +
> > > > +void spi_release_bus(struct spi_slave *slave) {
> > > > +       struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
> > > > +
> > > > +       espi_release_bus(fsl);
> > > > +}
> > > > +
> > > > +int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void
> *dout,
> > > > +            void *din, unsigned long flags) {
> > > > +       struct fsl_spi_slave *fsl = (struct fsl_spi_slave *)slave;
> > > > +
> > > > +       return espi_xfer(fsl, slave->cs, bitlen, dout, din,
> > > > +flags); } #else static void __espi_set_speed(struct fsl_spi_slave *fsl) {
> > > > +       espi_setup_slave(fsl);
> > > > +
> > > > +       /* Set eSPI BRG clock source */
> > > > +       out_be32(&fsl->espi->csmode[fsl->cs],
> > > > +                in_be32(&fsl->espi->csmode[fsl->cs])
> > > > +                        | ESPI_CSMODE_PM(fsl->pm) |
> fsl->div16);
> > > > + }
> > > > +
> > > > +static void __espi_set_mode(struct fsl_spi_slave *fsl) {
> > > > +       /* Set eSPI mode */
> > > > +       if (fsl->mode & SPI_CPHA)
> > > > +               out_be32(&fsl->espi->csmode[fsl->cs],
> > > > +                        in_be32(&fsl->espi->csmode[fsl->cs])
> > > > +                               |
> > > ESPI_CSMODE_CP_BEGIN_EDGCLK);
> > > > +       if (fsl->mode & SPI_CPOL)
> > > > +               out_be32(&fsl->espi->csmode[fsl->cs],
> > > > +                        in_be32(&fsl->espi->csmode[fsl->cs])
> > > > +                               |
> > > ESPI_CSMODE_CI_INACTIVEHIGH); }
> > > > +
> > > > +static int fsl_espi_claim_bus(struct udevice *dev) {
> > > > +       struct udevice *bus = dev->parent;
> > > > +       struct fsl_spi_slave  *fsl =  dev_get_priv(bus);
> > > > +
> > > > +       espi_claim_bus(fsl, fsl->cs);
> > > > +
> > > > +       return 0;
> > > > +}
> > > > +
> > > > +static int fsl_espi_release_bus(struct udevice *dev) {
> > > > +       struct udevice *bus = dev->parent;
> > > > +       struct fsl_spi_slave *fsl = dev_get_priv(bus);
> > > > +
> > > > +       espi_release_bus(fsl);
> > > > +
> > > > +       return 0;
> > > > +}
> > > > +
> > > > +static int fsl_espi_xfer(struct udevice *dev, unsigned int bitlen,
> > > > +                        const void *dout, void *din, unsigned
> > > > +long
> > > > +flags) {
> > > > +       struct udevice *bus = dev->parent;
> > > > +       struct fsl_spi_slave *fsl = dev_get_priv(bus);
> > > > +
> > > > +       return espi_xfer(fsl, fsl->cs, bitlen, dout, din, flags);
> > > > + }
> > > > +
> > > > +static int fsl_espi_set_speed(struct udevice *bus, uint speed) {
> > > > +       struct fsl_spi_slave *fsl = dev_get_priv(bus);
> > > > +
> > > > +       debug("%s speed %u\n", __func__, speed);
> > > > +       fsl->speed_hz = speed;
> > > > +
> > > > +       __espi_set_speed(fsl);
> > > > +
> > > > +       return 0;
> > > > +}
> > > > +
> > > > +static int fsl_espi_set_mode(struct udevice *bus, uint mode) {
> > > > +       struct fsl_spi_slave *fsl = dev_get_priv(bus);
> > > > +
> > > > +       debug("%s mode %u\n", __func__, mode);
> > > > +       fsl->mode = mode;
> > > > +
> > > > +       __espi_set_mode(fsl);
> > > > +
> > > > +       return 0;
> > > > +}
> > > > +
> > > > +static int fsl_espi_child_pre_probe(struct udevice *dev) {
> > > > +       struct dm_spi_slave_platdata *slave_plat =
> > > dev_get_parent_platdata(dev);
> > > > +       struct udevice *bus = dev->parent;
> > > > +       struct fsl_spi_slave *fsl = dev_get_priv(bus);
> > > > +
> > > > +       debug("%s cs %u\n", __func__, slave_plat->cs);
> > > > +       fsl->cs = slave_plat->cs;
> > > > +
> > > > +       return 0;
> > > > +}
> > > > +
> > > > +static int fsl_espi_probe(struct udevice *bus) {
> > > > +       struct fsl_espi_platdata *plat = dev_get_platdata(bus);
> > > > +       struct fsl_spi_slave *fsl = dev_get_priv(bus);
> > > > +
> > > > +       fsl->espi = (ccsr_espi_t *)((u32)plat->regs_addr);
> > > > +       fsl->max_transfer_length = ESPI_MAX_DATA_TRANSFER_LEN;
> > > > +       fsl->speed_hz = plat->speed_hz;
> > > > +
> > > > +       debug("%s probe done, bus-num %d.\n", bus->name,
> > > > + bus->seq);
> > > > +
> > > > +       return 0;
> > > > +}
> > > > +
> > > > +static const struct dm_spi_ops fsl_espi_ops = {
> > > > +       .claim_bus      = fsl_espi_claim_bus,
> > > > +       .release_bus    = fsl_espi_release_bus,
> > > > +       .xfer           = fsl_espi_xfer,
> > > > +       .set_speed      = fsl_espi_set_speed,
> > > > +       .set_mode       = fsl_espi_set_mode,
> > > > +};
> > > > +
> > > > +#if CONFIG_IS_ENABLED(OF_CONTROL)
> > > && !CONFIG_IS_ENABLED(OF_PLATDATA)
> > > > +static int fsl_espi_ofdata_to_platdata(struct udevice *bus) {
> > > > +       fdt_addr_t addr;
> > > > +       struct fsl_espi_platdata   *plat = bus->platdata;
> > > > +       const void *blob = gd->fdt_blob;
> > > > +       int node = dev_of_offset(bus);
> > > > +
> > > > +       addr = dev_read_addr(bus);
> > > > +       if (addr == FDT_ADDR_T_NONE)
> > > > +               return -EINVAL;
> > > > +
> > > > +       plat->regs_addr = lower_32_bits(addr);
> > > > +       plat->speed_hz = fdtdec_get_int(blob, node,
> > > "spi-max-frequency",
> > > > +
> > > FSL_ESPI_DEFAULT_SCK_FREQ);
> > > > +
> > > > +       debug("ESPI: regs=%p, max-frequency=%d\n",
> > > > +             &plat->regs_addr, plat->speed_hz);
> > > > +
> > > > +       return 0;
> > > > +}
> > > > +
> > > > +static const struct udevice_id fsl_espi_ids[] = {
> > > > +       { .compatible = "fsl,mpc8536-espi" },
> > > > +       { }
> > > > +};
> > > > +#endif
> > > > +
> > > > +U_BOOT_DRIVER(fsl_espi) = {
> > > > +       .name   = "fsl_espi",
> > > > +       .id     = UCLASS_SPI,
> > > > +#if CONFIG_IS_ENABLED(OF_CONTROL)
> > > && !CONFIG_IS_ENABLED(OF_PLATDATA)
> > > > +       .of_match = fsl_espi_ids,
> > > > +       .ofdata_to_platdata = fsl_espi_ofdata_to_platdata, #endif
> > > > +       .ops    = &fsl_espi_ops,
> > > > +       .platdata_auto_alloc_size = sizeof(struct fsl_espi_platdata),
> > > > +       .priv_auto_alloc_size = sizeof(struct fsl_spi_slave),
> > > > +       .probe  = fsl_espi_probe,
> > > > +       .child_pre_probe = fsl_espi_child_pre_probe, }; #endif
> > >
> > > It still has nondm code, does it required for SPL due to foot-print
> restrictions?
> > > How much are the numbers please?
> >
> > As the SPL is non-DM on these platforms, the SPL of SPI flash boot still needs
> these non-DM code.
> > What does the 'foot-print restrictions' mean? I don't know the background,
> since I just take over this task.
> 
> foot-print here mean size of the binary. what if the driver has only DM code
> with DM_SPI_FLASH?

Thanks a lot for the clarification, the defined CONFIG_SPL_MAX_SIZE values are
different on FSL PowerPC platforms, the least is 4KB on some P1 and P2 boards,
I don't know if the size is the restriction, no one is working on the SPL DM
conversion so far.

As the DM_SPI_FLASH depends DM&&DM_SPI, I don't think the non-DM SPL will
Work with only DM code in SPI flash driver. 

Thanks,
Zhiqiang

> 
> Jagan.


More information about the U-Boot mailing list