[PATCH v5 00/21] mtd: spi-nor-core: add xSPI Octal DTR support

[Pratyush Yadav]

Hi,

This series adds support for octal DTR flashes in the spi-nor framework,
and then adds hooks for the Cypress Semper flash which is an xSPI
compliant Octal DTR flash.

The Cadence QSPI controller driver is also updated to run in Octal DTR
mode.

Tested on TI J721e EVM.

The Travis CI build can be found here [0]. It is currently in progress,
but I ran an earlier build before rebasing on latest master and it
passed.

[0] https://travis-ci.org/github/prati0100/uboot/builds/694602802

Changes in v5:
- Introduce spi_nor_set_fixups(). Earlier, the fixup members of each
  flash was specified in spi-nor-ids.c. This meant they had to be
  declared as extern in sf_internal.h. But since spi-nor-tiny.c also
  uses it, and it doesn't have those fixups, they had to be put behind
  in an ifdef. The ".fixups = " assignment in spi-nor-ids.c also had to
  be put in an ifdef to account for spi-nor-tiny.c not having the fixup
  hooks. On top of this, the fixup of each flash is behind the flash's
  config.

  All this led to a soup of ifdefs that wasn't easy to digest. So don't
  set the fixups in the common code. Instead, add a function in
  spi-nor-core.c that sets the fixups of each flash. This isn't ideal,
  but its the best compromise I could figure out.

- Fix build breaking when CONFIG_SPL_SPI_FLASH_TINY is enabled because
  spi-nor-tiny did not have spi_nor_remove().

- The build was breaking in x530 because of SPL size too big. Fix it by
  the below changes.

- Re-introduce old hwcaps selection logic and put the new one behind a
  config. This lets boards with size restrictions use the old logic
  which takes up less space. The code was getting hard to manage with
  the old code behind ifdefs. So, re-structure the old hwcaps selection
  logic and move it into one function: spi_nor_adjust_hwcaps(). This
  way, the common code just calls spi_nor_adjust_hwcaps(), but the old
  or new hwcaps selection is used based on the config option selected.

- Put spi_nor_soft_reset() behind the config option SPI_NOR_SOFT_RESET.

- Rename the config option used for soft resetting on boot to
  SPI_NOR_SOFT_RESET_ON_BOOT to make its intention clearer.

- Put the fixup hooks of MT35XU512ABA and S28HS512T flashes behind
  config options to reduce code size on platforms that don't need them.

- Build were breaking with boards that use spi-mem-nodm.c because it
  doesn't have spi_mem_supports_op() which is needed for smart hwcaps
  selection. Add an equivalent to spi_mem_default_supports_op() there.

- Replace uses of sizeof(op->cmd.opcode) with op->cmd.nbytes.

- Do not set quad_enable to NULL if the value is set to reserved.
  Instead just print a warning and go on. quad_enable should be set to
  NULL in fixup hooks instead. Suggested on the Linux list.

- Set dummy cycles for DTR mode in spi_nor_micron_octal_dtr_enable()
  instead of in the post sfdp hook. This keeps the flash functional in
  case Octal DTR mode is not selected.

- Only use nor->rdsr_addr_nbytes and nor->rdsr_dummy when in Octal DTR
  mode. This makes sure the flash is functional in case Octal DTR is not
  selected.

- Rebase on latest master and fix a small merge conflict.

Changes in v4:
- Fix BFPT parsing stopping too early for JESD216 rev B flashes.

- Instead of just checking for spi_nor_get_protocol_width() in
  spi_nor_octal_dtr_enable(), make sure the protocol is
  SNOR_PROTO_8_8_8_DTR since get_protocol_width() only cares about data
  width.

- Do not enable stateful X-X-X modes if the reset line is broken.

- Instead of setting SNOR_READ_HWCAPS_8_8_8_DTR from Profile 1.0 table
  parsing, do it in spi_nor_info_init_params() instead based on the
  SPI_NOR_OCTAL_DTR_READ flag instead.

- Set SNOR_HWCAPS_PP_8_8_8_DTR in s28hs post_sfdp hook since this
  capability is no longer set in Profile 1.0 parsing.

- Rename spi_nor_cypress_octal_enable() to
  spi_nor_cypress_octal_dtr_enable().

- Instead of hard-coding 8D-8D-8D Fast Read dummy cycles to 20, find
  them out from the Profile 1.0 table.

- Call post-bfpt fixup when exiting early because of JESD rev A.

- Do not make an invalid Quad Enable BFPT field a fatal error. Silently
  ignore it by assuming no quad enable bit is present.

- Set cmd.nbytes to 1 when using SPI_MEM_OP_CMD().

- Reject ops with more than 1 command byte in
  spi_mem_default_supports_op().

- Drop flag SPI_NOR_SOFT_RESET. Instead, discover soft reset capability
  via BFPT.

- Add missing headers that were removed from common header.

Changes in v3:
- Read 2 bytes in Octal DTR mode when reading SR and FSR to avoid
  tripping up controllers.

- Use op->data.nbytes as a measure of whether the data phase exists or
  not. This fixes data buswidth not being updadted for SR and FSR reads
  because they keep data buffer as NULL when calling spi_nor_setup_op().

- Add support for Micron mt35xu512aba to run in Octal DTR mode.


Pratyush Yadav (21):
  spi: spi-mem: allow specifying whether an op is DTR or not
  spi: spi-mem: allow specifying a command's extension
  spi: cadence-qspi: Do not calibrate when device tree sets read delay
  spi: cadence-qspi: Add support for octal DTR flashes
  arm: mvebu: x530: Disable smart hwcaps selection
  mtd: spi-nor-core: Add a ->setup() hook
  mtd: spi-nor-core: Move SFDP related declarations to top
  mtd: spi-nor-core: Introduce flash-specific fixup hooks
  mtd: spi-nor-core: Rework hwcaps selection
  mtd: spi-nor-core: Add support for DTR protocol
  mtd: spi-nor-core: prepare BFPT parsing for JESD216 rev D
  mtd: spi-nor-core: Get command opcode extension type from BFPT
  mtd: spi-nor-core: Parse xSPI Profile 1.0 table
  mtd: spi-nor-core: Prepare Read SR and FSR for Octal DTR mode
  mtd: spi-nor-core: Enable octal DTR mode when possible
  mtd: spi-nor-core: Do not make invalid quad enable fatal
  mtd: spi-nor-core: Detect Soft Reset sequence support from BFPT
  mtd: spi-nor-core: Perform a Soft Reset on shutdown
  mtd: spi-nor-core: Perform a Soft Reset on boot
  mtd: spi-nor-core: Add support for Cypress Semper flash
  mtd: spi-nor-core: Allow using Micron mt35xu512aba in Octal DTR mode

 configs/x530_defconfig         |    1 +
 drivers/mtd/spi/Kconfig        |   42 +
 drivers/mtd/spi/sf_internal.h  |    1 +
 drivers/mtd/spi/sf_probe.c     |   11 +
 drivers/mtd/spi/spi-nor-core.c | 1345 ++++++++++++++++++++++++++------
 drivers/mtd/spi/spi-nor-ids.c  |    7 +-
 drivers/mtd/spi/spi-nor-tiny.c |   22 -
 drivers/spi/cadence_qspi.c     |   87 ++-
 drivers/spi/cadence_qspi.h     |   15 +-
 drivers/spi/cadence_qspi_apb.c |  286 ++++++-
 drivers/spi/mtk_snfi_spi.c     |    3 +-
 drivers/spi/spi-mem-nodm.c     |   66 +-
 drivers/spi/spi-mem.c          |   16 +-
 include/linux/mtd/spi-nor.h    |  275 +++++--
 include/spi-mem.h              |   17 +-
 15 files changed, 1822 insertions(+), 372 deletions(-)

--
2.27.0