rockchip: correctly set vop0 or vop1

[Arnaud Patard (Rtp)]

Patrick Wildt <patrick at blueri.se> writes:

> On Mon, Jun 08, 2020 at 10:18:19AM +0200, Arnaud Patard wrote:
>> Patrick Wildt <patrick at blueri.se> writes:
>> 
>> Hi,
>> 
>> > The EDP_LCDC_SEL bit has to be set correctly to select vop0 or
>> > vop1, but so far we have set it in both conditions, which is not
>> > correct.
>> >
>> > Can someone verify this is the correct way round?  vop1 -> set,
>> > vop0 -> clear?
>> >
>> > Signed-off-by: Patrick Wildt <patrick at blueri.se>
>> >
>> > diff --git a/drivers/video/rockchip/rk_edp.c b/drivers/video/rockchip/rk_edp.c
>> > index 92188be9275..000bd481408 100644
>> > --- a/drivers/video/rockchip/rk_edp.c
>> > +++ b/drivers/video/rockchip/rk_edp.c
>> > @@ -1062,7 +1062,8 @@ static int rk_edp_probe(struct udevice *dev)
>> >  	rk_setreg(&priv->grf->soc_con12, 1 << 4);
>> >  
>> >  	/* select epd signal from vop0 or vop1 */
>> > -	rk_setreg(&priv->grf->soc_con6, (vop_id == 1) ? (1 << 5) : (1 << 5));
>> > +	rk_clrsetreg(&priv->grf->soc_con6, (1 << 5),
>> > +	    (vop_id == 1) ? (1 << 5) : (0 << 5));
>> 
>> While working on PBP EDP support, found this too but I'm not sure it's
>> fine or not. For rk3399, my (not yet published) patch is doing:
>> 
>> +       if (vop_id == 0)
>> +               rk_clrreg(&priv->grf->soc_con20, (1 << 5));
>> +       else
>> +               rk_setreg(&priv->grf->soc_con20, (1 << 5));
>> 
>> I believe that the rk3288 may need similar treatment but I've yet to
>> look at the rk3288 manual.
>> 
>> Arnaud
>
> Yes, it does.  If you look at the linux code, they have:
>
> static const struct rockchip_dp_chip_data rk3399_edp = {
>         .lcdsel_grf_reg = RK3399_GRF_SOC_CON20,
>         .lcdsel_big = HIWORD_UPDATE(0, RK3399_EDP_LCDC_SEL),
>         .lcdsel_lit = HIWORD_UPDATE(RK3399_EDP_LCDC_SEL, RK3399_EDP_LCDC_SEL),
>         .chip_type = RK3399_EDP,
> };
>
> static const struct rockchip_dp_chip_data rk3288_dp = {
>         .lcdsel_grf_reg = RK3288_GRF_SOC_CON6,
>         .lcdsel_big = HIWORD_UPDATE(0, RK3288_EDP_LCDC_SEL),
>         .lcdsel_lit = HIWORD_UPDATE(RK3288_EDP_LCDC_SEL, RK3288_EDP_LCDC_SEL),
>         .chip_type = RK3288_DP,
> };
>
> which indicates that for rk3399 *and* rk3288 the bit has to be set to
> select "lit".  Now your diff looks equivalent to mine, apart from using
> a different operation to achieve the same goal.
>
> The linux code does
>
>         ret = drm_of_encoder_active_endpoint_id(dp->dev->of_node, encoder);
>         if (ret < 0)
>                 return;
>
>         if (ret)
>                 val = dp->data->lcdsel_lit;
>         else
>                 val = dp->data->lcdsel_big;
>
> Assuming that endpoint_id essentiall returns vop id 0 or vop id 1, this
> would mean that vop1 -> lit -> set bit and vop0 -> big -> clr bit.
>
> That said, my diff seems to be fine, and your RK3399 code as well.  Do
> you agree?

According to the code you've shown, it should be fine for rk3288 I guess
but not for rk3399. Please note that it's grf soc_con6 register for rk3288
but grf soc_con20 for rk3399.

Arnaud