[PATCH v1 5/9] ram: octeon: Add MIPS Octeon3 DDR4 support (part 1/3)
Stefan Roese
sr at denx.de
Tue Jun 9 11:42:30 CEST 2020
From: Aaron Williams <awilliams at marvell.com>
This Octeon 3 DDR driver is ported from the 2013 Cavium / Marvell U-Boot
repository. It currently supports DDR4 on Octeon 3. It can be later
extended to support also DDR3 and Octeon 2 platforms.
Part 1 adds the base U-Boot RAM driver, which will be instantiated by
the DT based probing.
Signed-off-by: Aaron Williams <awilliams at marvell.com>
Signed-off-by: Stefan Roese <sr at denx.de>
---
drivers/ram/octeon/octeon_ddr.c | 2716 +++++++++++++++++++++++++++++++
1 file changed, 2716 insertions(+)
create mode 100644 drivers/ram/octeon/octeon_ddr.c
diff --git a/drivers/ram/octeon/octeon_ddr.c b/drivers/ram/octeon/octeon_ddr.c
new file mode 100644
index 0000000000..fdb54ed2db
--- /dev/null
+++ b/drivers/ram/octeon/octeon_ddr.c
@@ -0,0 +1,2716 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 Marvell International Ltd.
+ *
+ * https://spdx.org/licenses
+ */
+
+#include <common.h>
+#include <command.h>
+#include <dm.h>
+#include <hang.h>
+#include <i2c.h>
+#include <ram.h>
+#include <time.h>
+
+#include <linux/io.h>
+
+#include <mach/octeon_ddr.h>
+
+#define CONFIG_REF_HERTZ 50000000
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Sign of an integer */
+static s64 _sign(s64 v)
+{
+ return (v < 0);
+}
+
+#ifndef DDR_NO_DEBUG
+char *lookup_env(struct ddr_priv *priv, const char *format, ...)
+{
+ char *s;
+ unsigned long value;
+ va_list args;
+ char buffer[64];
+
+ va_start(args, format);
+ vsnprintf(buffer, sizeof(buffer), format, args);
+ va_end(args);
+
+ s = ddr_getenv_debug(priv, buffer);
+ if (s) {
+ value = simple_strtoul(s, NULL, 0);
+ printf("Parameter found in environment %s=\"%s\" 0x%lx (%ld)\n",
+ buffer, s, value, value);
+ }
+
+ return s;
+}
+
+char *lookup_env_ull(struct ddr_priv *priv, const char *format, ...)
+{
+ char *s;
+ u64 value;
+ va_list args;
+ char buffer[64];
+
+ va_start(args, format);
+ vsnprintf(buffer, sizeof(buffer), format, args);
+ va_end(args);
+
+ s = ddr_getenv_debug(priv, buffer);
+ if (s) {
+ value = simple_strtoull(s, NULL, 0);
+ printf("Parameter found in environment. %s = 0x%016llx\n",
+ buffer, value);
+ }
+
+ return s;
+}
+#else
+char *lookup_env(struct ddr_priv *priv, const char *format, ...)
+{
+ return NULL;
+}
+
+char *lookup_env_ull(struct ddr_priv *priv, const char *format, ...)
+{
+ return NULL;
+}
+#endif
+
+/* Number of L2C Tag-and-data sections (TADs) that are connected to LMC. */
+#define CVMX_L2C_TADS ((OCTEON_IS_MODEL(OCTEON_CN68XX) || \
+ OCTEON_IS_MODEL(OCTEON_CN73XX) || \
+ OCTEON_IS_MODEL(OCTEON_CNF75XX)) ? 4 : \
+ (OCTEON_IS_MODEL(OCTEON_CN78XX)) ? 8 : 1)
+
+/* Number of L2C IOBs connected to LMC. */
+#define CVMX_L2C_IOBS ((OCTEON_IS_MODEL(OCTEON_CN68XX) || \
+ OCTEON_IS_MODEL(OCTEON_CN78XX) || \
+ OCTEON_IS_MODEL(OCTEON_CN73XX) || \
+ OCTEON_IS_MODEL(OCTEON_CNF75XX)) ? 2 : 1)
+
+#define CVMX_L2C_MAX_MEMSZ_ALLOWED (OCTEON_IS_OCTEON2() ? \
+ (32 * CVMX_L2C_TADS) : \
+ (OCTEON_IS_MODEL(OCTEON_CN70XX) ? \
+ 512 : (OCTEON_IS_OCTEON3() ? 1024 : 0)))
+
+/**
+ * Initialize the BIG address in L2C+DRAM to generate proper error
+ * on reading/writing to an non-existent memory location.
+ *
+ * @param node OCX CPU node number
+ * @param mem_size Amount of DRAM configured in MB.
+ * @param mode Allow/Disallow reporting errors L2C_INT_SUM[BIGRD,BIGWR].
+ */
+static void cvmx_l2c_set_big_size(struct ddr_priv *priv, u64 mem_size, int mode)
+{
+ if ((OCTEON_IS_OCTEON2() || OCTEON_IS_OCTEON3()) &&
+ !OCTEON_IS_MODEL(OCTEON_CN63XX_PASS1_X)) {
+ union cvmx_l2c_big_ctl big_ctl;
+ int bits = 0, zero_bits = 0;
+ u64 mem;
+
+ if (mem_size > (CVMX_L2C_MAX_MEMSZ_ALLOWED * 1024ull)) {
+ printf("WARNING: Invalid memory size(%lld) requested, should be <= %lld\n",
+ mem_size,
+ (u64)CVMX_L2C_MAX_MEMSZ_ALLOWED * 1024);
+ mem_size = CVMX_L2C_MAX_MEMSZ_ALLOWED * 1024;
+ }
+
+ mem = mem_size;
+ while (mem) {
+ if ((mem & 1) == 0)
+ zero_bits++;
+ bits++;
+ mem >>= 1;
+ }
+
+ if ((bits - zero_bits) != 1 || (bits - 9) <= 0) {
+ printf("ERROR: Invalid DRAM size (%lld) requested, refer to L2C_BIG_CTL[maxdram] for valid options.\n",
+ mem_size);
+ return;
+ }
+
+ /*
+ * The BIG/HOLE is logic is not supported in pass1 as per
+ * Errata L2C-17736
+ */
+ if (mode == 0 && OCTEON_IS_MODEL(OCTEON_CN78XX_PASS1_X))
+ mode = 1;
+
+ big_ctl.u64 = 0;
+ big_ctl.s.maxdram = bits - 9;
+ big_ctl.cn61xx.disable = mode;
+ l2c_wr(priv, CVMX_L2C_BIG_CTL, big_ctl.u64);
+ }
+}
+
+static u32 octeon3_refclock(u32 alt_refclk, u32 ddr_hertz,
+ struct dimm_config *dimm_config)
+{
+ u32 ddr_ref_hertz = CONFIG_REF_HERTZ;
+ int ddr_type;
+ int spd_dimm_type;
+
+ debug("%s(%u, %u, %p)\n", __func__, alt_refclk, ddr_hertz, dimm_config);
+
+ /* Octeon 3 case... */
+
+ /* we know whether alternate refclk is always wanted
+ * we also know already if we want 2133 MT/s
+ * if alt refclk not always wanted, then probe DDR and
+ * DIMM type if DDR4 and RDIMMs, then set desired refclk
+ * to 100MHz, otherwise to default (50MHz)
+ * depend on ddr_initialize() to do the refclk selection
+ * and validation/
+ */
+ if (alt_refclk) {
+ /*
+ * If alternate refclk was specified, let it override
+ * everything
+ */
+ ddr_ref_hertz = alt_refclk * 1000000;
+ printf("%s: DRAM init: %d MHz refclk is REQUESTED ALWAYS\n",
+ __func__, alt_refclk);
+ } else if (ddr_hertz > 1000000000) {
+ ddr_type = get_ddr_type(dimm_config, 0);
+ spd_dimm_type = get_dimm_module_type(dimm_config, 0, ddr_type);
+
+ debug("ddr type: 0x%x, dimm type: 0x%x\n", ddr_type,
+ spd_dimm_type);
+ /* Is DDR4 and RDIMM just to be sure. */
+ if (ddr_type == DDR4_DRAM &&
+ (spd_dimm_type == 1 || spd_dimm_type == 5 ||
+ spd_dimm_type == 8)) {
+ /* Yes, we require 100MHz refclk, so set it. */
+ ddr_ref_hertz = 100000000;
+ puts("DRAM init: 100 MHz refclk is REQUIRED\n");
+ }
+ }
+
+ debug("%s: speed: %u\n", __func__, ddr_ref_hertz);
+ return ddr_ref_hertz;
+}
+
+int encode_row_lsb_ddr3(int row_lsb)
+{
+ int row_lsb_start = 14;
+
+ /* Decoding for row_lsb */
+ /* 000: row_lsb = mem_adr[14] */
+ /* 001: row_lsb = mem_adr[15] */
+ /* 010: row_lsb = mem_adr[16] */
+ /* 011: row_lsb = mem_adr[17] */
+ /* 100: row_lsb = mem_adr[18] */
+ /* 101: row_lsb = mem_adr[19] */
+ /* 110: row_lsb = mem_adr[20] */
+ /* 111: RESERVED */
+
+ if (octeon_is_cpuid(OCTEON_CN6XXX) ||
+ octeon_is_cpuid(OCTEON_CNF7XXX) || octeon_is_cpuid(OCTEON_CN7XXX))
+ row_lsb_start = 14;
+ else
+ printf("ERROR: Unsupported Octeon model: 0x%x\n",
+ read_c0_prid());
+
+ return row_lsb - row_lsb_start;
+}
+
+int encode_pbank_lsb_ddr3(int pbank_lsb)
+{
+ /* Decoding for pbank_lsb */
+ /* 0000:DIMM = mem_adr[28] / rank = mem_adr[27] (if RANK_ENA) */
+ /* 0001:DIMM = mem_adr[29] / rank = mem_adr[28] " */
+ /* 0010:DIMM = mem_adr[30] / rank = mem_adr[29] " */
+ /* 0011:DIMM = mem_adr[31] / rank = mem_adr[30] " */
+ /* 0100:DIMM = mem_adr[32] / rank = mem_adr[31] " */
+ /* 0101:DIMM = mem_adr[33] / rank = mem_adr[32] " */
+ /* 0110:DIMM = mem_adr[34] / rank = mem_adr[33] " */
+ /* 0111:DIMM = 0 / rank = mem_adr[34] " */
+ /* 1000-1111: RESERVED */
+
+ int pbank_lsb_start = 0;
+
+ if (octeon_is_cpuid(OCTEON_CN6XXX) ||
+ octeon_is_cpuid(OCTEON_CNF7XXX) || octeon_is_cpuid(OCTEON_CN7XXX))
+ pbank_lsb_start = 28;
+ else
+ printf("ERROR: Unsupported Octeon model: 0x%x\n",
+ read_c0_prid());
+
+ return pbank_lsb - pbank_lsb_start;
+}
+
+static void set_ddr_clock_initialized(struct ddr_priv *priv, int if_num,
+ bool inited_flag)
+{
+ priv->ddr_clock_initialized[if_num] = inited_flag;
+}
+
+static int ddr_clock_initialized(struct ddr_priv *priv, int if_num)
+{
+ return priv->ddr_clock_initialized[if_num];
+}
+
+static void set_ddr_memory_preserved(struct ddr_priv *priv)
+{
+ priv->ddr_memory_preserved = true;
+}
+
+bool ddr_memory_preserved(struct ddr_priv *priv)
+{
+ return priv->ddr_memory_preserved;
+}
+
+static void cn78xx_lmc_dreset_init(struct ddr_priv *priv, int if_num)
+{
+ union cvmx_lmcx_dll_ctl2 dll_ctl2;
+
+ /*
+ * The remainder of this section describes the sequence for LMCn.
+ *
+ * 1. If not done already, write LMC(0..3)_DLL_CTL2 to its reset value
+ * (except without changing the LMC(0..3)_DLL_CTL2[INTF_EN] value from
+ * that set in the prior Step 3), including
+ * LMC(0..3)_DLL_CTL2[DRESET] = 1.
+ *
+ * 2. Without changing any other LMC(0..3)_DLL_CTL2 fields, write
+ * LMC(0..3)_DLL_CTL2[DLL_BRINGUP] = 1.
+ */
+
+ dll_ctl2.u64 = lmc_rd(priv, CVMX_LMCX_DLL_CTL2(if_num));
+ dll_ctl2.cn78xx.dll_bringup = 1;
+ lmc_wr(priv, CVMX_LMCX_DLL_CTL2(if_num), dll_ctl2.u64);
+
+ /*
+ * 3. Read LMC(0..3)_DLL_CTL2 and wait for the result.
+ */
+
+ lmc_rd(priv, CVMX_LMCX_DLL_CTL2(if_num));
+
+ /*
+ * 4. Wait for a minimum of 10 LMC CK cycles.
+ */
+
+ udelay(1);
+
+ /*
+ * 5. Without changing any other fields in LMC(0..3)_DLL_CTL2, write
+ * LMC(0..3)_DLL_CTL2[QUAD_DLL_ENA] = 1.
+ * LMC(0..3)_DLL_CTL2[QUAD_DLL_ENA] must not change after this point
+ * without restarting the LMCn DRESET initialization sequence.
+ */
+
+ dll_ctl2.u64 = lmc_rd(priv, CVMX_LMCX_DLL_CTL2(if_num));
+ dll_ctl2.cn78xx.quad_dll_ena = 1;
+ lmc_wr(priv, CVMX_LMCX_DLL_CTL2(if_num), dll_ctl2.u64);
+
+ /*
+ * 6. Read LMC(0..3)_DLL_CTL2 and wait for the result.
+ */
+
+ lmc_rd(priv, CVMX_LMCX_DLL_CTL2(if_num));
+
+ /*
+ * 7. Wait a minimum of 10 us.
+ */
+
+ udelay(10);
+
+ /*
+ * 8. Without changing any other fields in LMC(0..3)_DLL_CTL2, write
+ * LMC(0..3)_DLL_CTL2[DLL_BRINGUP] = 0.
+ * LMC(0..3)_DLL_CTL2[DLL_BRINGUP] must not change after this point
+ * without restarting the LMCn DRESET initialization sequence.
+ */
+
+ dll_ctl2.u64 = lmc_rd(priv, CVMX_LMCX_DLL_CTL2(if_num));
+ dll_ctl2.cn78xx.dll_bringup = 0;
+ lmc_wr(priv, CVMX_LMCX_DLL_CTL2(if_num), dll_ctl2.u64);
+
+ /*
+ * 9. Read LMC(0..3)_DLL_CTL2 and wait for the result.
+ */
+
+ lmc_rd(priv, CVMX_LMCX_DLL_CTL2(if_num));
+
+ /*
+ * 10. Without changing any other fields in LMC(0..3)_DLL_CTL2, write
+ * LMC(0..3)_DLL_CTL2[DRESET] = 0.
+ * LMC(0..3)_DLL_CTL2[DRESET] must not change after this point without
+ * restarting the LMCn DRESET initialization sequence.
+ *
+ * After completing LMCn DRESET initialization, all LMC CSRs may be
+ * accessed. Prior to completing LMC DRESET initialization, only
+ * LMC(0..3)_DDR_PLL_CTL, LMC(0..3)_DLL_CTL2, LMC(0..3)_RESET_CTL, and
+ * LMC(0..3)_COMP_CTL2 LMC CSRs can be accessed.
+ */
+
+ dll_ctl2.u64 = lmc_rd(priv, CVMX_LMCX_DLL_CTL2(if_num));
+ dll_ctl2.cn78xx.dreset = 0;
+ lmc_wr(priv, CVMX_LMCX_DLL_CTL2(if_num), dll_ctl2.u64);
+}
+
+int initialize_ddr_clock(struct ddr_priv *priv, struct ddr_conf *ddr_conf,
+ u32 cpu_hertz, u32 ddr_hertz, u32 ddr_ref_hertz,
+ int if_num, u32 if_mask)
+{
+ char *s;
+
+ if (ddr_clock_initialized(priv, if_num))
+ return 0;
+
+ if (!ddr_clock_initialized(priv, 0)) { /* Do this once */
+ union cvmx_lmcx_reset_ctl reset_ctl;
+ int i;
+
+ /*
+ * Check to see if memory is to be preserved and set global
+ * flag
+ */
+ for (i = 3; i >= 0; --i) {
+ if ((if_mask & (1 << i)) == 0)
+ continue;
+
+ reset_ctl.u64 = lmc_rd(priv, CVMX_LMCX_RESET_CTL(i));
+ if (reset_ctl.s.ddr3psv == 1) {
+ debug("LMC%d Preserving memory\n", i);
+ set_ddr_memory_preserved(priv);
+
+ /* Re-initialize flags */
+ reset_ctl.s.ddr3pwarm = 0;
+ reset_ctl.s.ddr3psoft = 0;
+ reset_ctl.s.ddr3psv = 0;
+ lmc_wr(priv, CVMX_LMCX_RESET_CTL(i),
+ reset_ctl.u64);
+ }
+ }
+ }
+
+ /*
+ * ToDo: Add support for these SoCs:
+ *
+ * if (octeon_is_cpuid(OCTEON_CN63XX) ||
+ * octeon_is_cpuid(OCTEON_CN66XX) ||
+ * octeon_is_cpuid(OCTEON_CN61XX) || octeon_is_cpuid(OCTEON_CNF71XX))
+ *
+ * and
+ *
+ * if (octeon_is_cpuid(OCTEON_CN68XX))
+ *
+ * and
+ *
+ * if (octeon_is_cpuid(OCTEON_CN70XX))
+ *
+ */
+
+ if (octeon_is_cpuid(OCTEON_CN78XX) || octeon_is_cpuid(OCTEON_CN73XX) ||
+ octeon_is_cpuid(OCTEON_CNF75XX)) {
+ union cvmx_lmcx_dll_ctl2 dll_ctl2;
+ union cvmx_lmcx_dll_ctl3 ddr_dll_ctl3;
+ union cvmx_lmcx_ddr_pll_ctl ddr_pll_ctl;
+ struct dimm_config *dimm_config_table =
+ ddr_conf->dimm_config_table;
+ int en_idx, save_en_idx, best_en_idx = 0;
+ u64 clkf, clkr, max_clkf = 127;
+ u64 best_clkf = 0, best_clkr = 0;
+ u64 best_pll_MHz = 0;
+ u64 pll_MHz;
+ u64 min_pll_MHz = 800;
+ u64 max_pll_MHz = 5000;
+ u64 error;
+ u64 best_error;
+ u64 best_calculated_ddr_hertz = 0;
+ u64 calculated_ddr_hertz = 0;
+ u64 orig_ddr_hertz = ddr_hertz;
+ const int _en[] = { 1, 2, 3, 4, 5, 6, 7, 8, 10, 12 };
+ int override_pll_settings;
+ int new_bwadj;
+ int ddr_type;
+ int i;
+
+ /* ddr_type only indicates DDR4 or DDR3 */
+ ddr_type = (read_spd(&dimm_config_table[0], 0,
+ DDR4_SPD_KEY_BYTE_DEVICE_TYPE) ==
+ 0x0C) ? DDR4_DRAM : DDR3_DRAM;
+
+ /*
+ * 5.9 LMC Initialization Sequence
+ *
+ * There are 13 parts to the LMC initialization procedure:
+ *
+ * 1. DDR PLL initialization
+ *
+ * 2. LMC CK initialization
+ *
+ * 3. LMC interface enable initialization
+ *
+ * 4. LMC DRESET initialization
+ *
+ * 5. LMC CK local initialization
+ *
+ * 6. LMC RESET initialization
+ *
+ * 7. Early LMC initialization
+ *
+ * 8. LMC offset training
+ *
+ * 9. LMC internal Vref training
+ *
+ * 10. LMC deskew training
+ *
+ * 11. LMC write leveling
+ *
+ * 12. LMC read leveling
+ *
+ * 13. Final LMC initialization
+ *
+ * CN78XX supports two modes:
+ *
+ * - two-LMC mode: both LMCs 2/3 must not be enabled
+ * (LMC2/3_DLL_CTL2[DRESET] must be set to 1 and
+ * LMC2/3_DLL_CTL2[INTF_EN]
+ * must be set to 0) and both LMCs 0/1 must be enabled).
+ *
+ * - four-LMC mode: all four LMCs 0..3 must be enabled.
+ *
+ * Steps 4 and 6..13 should each be performed for each
+ * enabled LMC (either twice or four times). Steps 1..3 and
+ * 5 are more global in nature and each must be executed
+ * exactly once (not once per LMC) each time the DDR PLL
+ * changes or is first brought up. Steps 1..3 and 5 need
+ * not be performed if the DDR PLL is stable.
+ *
+ * Generally, the steps are performed in order. The exception
+ * is that the CK local initialization (step 5) must be
+ * performed after some DRESET initializations (step 4) and
+ * before other DRESET initializations when the DDR PLL is
+ * brought up or changed. (The CK local initialization uses
+ * information from some LMCs to bring up the other local
+ * CKs.) The following text describes these ordering
+ * requirements in more detail.
+ *
+ * Following any chip reset, the DDR PLL must be brought up,
+ * and all 13 steps should be executed. Subsequently, it is
+ * possible to execute only steps 4 and 6..13, or to execute
+ * only steps 8..13.
+ *
+ * The remainder of this section covers these initialization
+ * steps in sequence.
+ */
+
+ /* Do the following init only once */
+ if (if_num != 0)
+ goto not_if0;
+
+ /* Only for interface #0 ... */
+
+ /*
+ * 5.9.3 LMC Interface-Enable Initialization
+ *
+ * LMC interface-enable initialization (Step 3) must be#
+ * performed after Step 2 for each chip reset and whenever
+ * the DDR clock speed changes. This step needs to be
+ * performed only once, not once per LMC. Perform the
+ * following three substeps for the LMC interface-enable
+ * initialization:
+ *
+ * 1. Without changing any other LMC2_DLL_CTL2 fields
+ * (LMC(0..3)_DLL_CTL2 should be at their reset values after
+ * Step 1), write LMC2_DLL_CTL2[INTF_EN] = 1 if four-LMC
+ * mode is desired.
+ *
+ * 2. Without changing any other LMC3_DLL_CTL2 fields, write
+ * LMC3_DLL_CTL2[INTF_EN] = 1 if four-LMC mode is desired.
+ *
+ * 3. Read LMC2_DLL_CTL2 and wait for the result.
+ *
+ * The LMC2_DLL_CTL2[INTF_EN] and LMC3_DLL_CTL2[INTF_EN]
+ * values should not be changed by software from this point.
+ */
+
+ for (i = 0; i < 4; ++i) {
+ if ((if_mask & (1 << i)) == 0)
+ continue;
+
+ dll_ctl2.u64 = lmc_rd(priv, CVMX_LMCX_DLL_CTL2(i));
+
+ dll_ctl2.cn78xx.byp_setting = 0;
+ dll_ctl2.cn78xx.byp_sel = 0;
+ dll_ctl2.cn78xx.quad_dll_ena = 0;
+ dll_ctl2.cn78xx.dreset = 1;
+ dll_ctl2.cn78xx.dll_bringup = 0;
+ dll_ctl2.cn78xx.intf_en = 0;
+
+ lmc_wr(priv, CVMX_LMCX_DLL_CTL2(i), dll_ctl2.u64);
+ }
+
+ /*
+ * ###### Interface enable (intf_en) deferred until after
+ * DDR_DIV_RESET=0 #######
+ */
+
+ /*
+ * 5.9.1 DDR PLL Initialization
+ *
+ * DDR PLL initialization (Step 1) must be performed for each
+ * chip reset and whenever the DDR clock speed changes. This
+ * step needs to be performed only once, not once per LMC.
+ *
+ * Perform the following eight substeps to initialize the
+ * DDR PLL:
+ *
+ * 1. If not done already, write all fields in
+ * LMC(0..3)_DDR_PLL_CTL and
+ * LMC(0..1)_DLL_CTL2 to their reset values, including:
+ *
+ * .. LMC0_DDR_PLL_CTL[DDR_DIV_RESET] = 1
+ * .. LMC0_DLL_CTL2[DRESET] = 1
+ *
+ * This substep is not necessary after a chip reset.
+ *
+ */
+
+ ddr_pll_ctl.u64 = lmc_rd(priv, CVMX_LMCX_DDR_PLL_CTL(0));
+
+ ddr_pll_ctl.cn78xx.reset_n = 0;
+ ddr_pll_ctl.cn78xx.ddr_div_reset = 1;
+ ddr_pll_ctl.cn78xx.phy_dcok = 0;
+
+ /*
+ * 73XX pass 1.3 has LMC0 DCLK_INVERT tied to 1; earlier
+ * 73xx passes are tied to 0
+ *
+ * 75XX needs LMC0 DCLK_INVERT set to 1 to minimize duty
+ * cycle falling points
+ *
+ * and we default all other chips LMC0 to DCLK_INVERT=0
+ */
+ ddr_pll_ctl.cn78xx.dclk_invert =
+ !!(octeon_is_cpuid(OCTEON_CN73XX_PASS1_3) ||
+ octeon_is_cpuid(OCTEON_CNF75XX));
+
+ /*
+ * allow override of LMC0 desired setting for DCLK_INVERT,
+ * but not on 73XX;
+ * we cannot change LMC0 DCLK_INVERT on 73XX any pass
+ */
+ if (!(octeon_is_cpuid(OCTEON_CN73XX))) {
+ s = lookup_env(priv, "ddr0_set_dclk_invert");
+ if (s) {
+ ddr_pll_ctl.cn78xx.dclk_invert =
+ !!simple_strtoul(s, NULL, 0);
+ debug("LMC0: override DDR_PLL_CTL[dclk_invert] to %d\n",
+ ddr_pll_ctl.cn78xx.dclk_invert);
+ }
+ }
+
+ lmc_wr(priv, CVMX_LMCX_DDR_PLL_CTL(0), ddr_pll_ctl.u64);
+ debug("%-45s : 0x%016llx\n", "LMC0: DDR_PLL_CTL",
+ ddr_pll_ctl.u64);
+
+ // only when LMC1 is active
+ if (if_mask & 0x2) {
+ /*
+ * For CNF75XX, both LMC0 and LMC1 use the same PLL,
+ * so we use the LMC0 setting of DCLK_INVERT for LMC1.
+ */
+ if (!octeon_is_cpuid(OCTEON_CNF75XX)) {
+ int override = 0;
+
+ /*
+ * by default, for non-CNF75XX, we want
+ * LMC1 toggled LMC0
+ */
+ int lmc0_dclk_invert =
+ ddr_pll_ctl.cn78xx.dclk_invert;
+
+ /*
+ * FIXME: work-around for DDR3 UDIMM problems
+ * is to use LMC0 setting on LMC1 and if
+ * 73xx pass 1.3, we want to default LMC1
+ * DCLK_INVERT to LMC0, not the invert of LMC0
+ */
+ int lmc1_dclk_invert;
+
+ lmc1_dclk_invert =
+ ((ddr_type == DDR4_DRAM) &&
+ !octeon_is_cpuid(OCTEON_CN73XX_PASS1_3))
+ ? lmc0_dclk_invert ^ 1 :
+ lmc0_dclk_invert;
+
+ /*
+ * allow override of LMC1 desired setting for
+ * DCLK_INVERT
+ */
+ s = lookup_env(priv, "ddr1_set_dclk_invert");
+ if (s) {
+ lmc1_dclk_invert =
+ !!simple_strtoul(s, NULL, 0);
+ override = 1;
+ }
+ debug("LMC1: %s DDR_PLL_CTL[dclk_invert] to %d (LMC0 %d)\n",
+ (override) ? "override" :
+ "default", lmc1_dclk_invert,
+ lmc0_dclk_invert);
+
+ ddr_pll_ctl.cn78xx.dclk_invert =
+ lmc1_dclk_invert;
+ }
+
+ // but always write LMC1 CSR if it is active
+ lmc_wr(priv, CVMX_LMCX_DDR_PLL_CTL(1), ddr_pll_ctl.u64);
+ debug("%-45s : 0x%016llx\n",
+ "LMC1: DDR_PLL_CTL", ddr_pll_ctl.u64);
+ }
+
+ /*
+ * 2. If the current DRAM contents are not preserved (see
+ * LMC(0..3)_RESET_ CTL[DDR3PSV]), this is also an appropriate
+ * time to assert the RESET# pin of the DDR3/DDR4 DRAM parts.
+ * If desired, write
+ * LMC0_RESET_ CTL[DDR3RST] = 0 without modifying any other
+ * LMC0_RESET_CTL fields to assert the DDR_RESET_L pin.
+ * No action is required here to assert DDR_RESET_L
+ * following a chip reset. Refer to Section 5.9.6. Do this
+ * for all enabled LMCs.
+ */
+
+ for (i = 0; (!ddr_memory_preserved(priv)) && i < 4; ++i) {
+ union cvmx_lmcx_reset_ctl reset_ctl;
+
+ if ((if_mask & (1 << i)) == 0)
+ continue;
+
+ reset_ctl.u64 = lmc_rd(priv, CVMX_LMCX_RESET_CTL(i));
+ reset_ctl.cn78xx.ddr3rst = 0; /* Reset asserted */
+ debug("LMC%d Asserting DDR_RESET_L\n", i);
+ lmc_wr(priv, CVMX_LMCX_RESET_CTL(i), reset_ctl.u64);
+ lmc_rd(priv, CVMX_LMCX_RESET_CTL(i));
+ }
+
+ /*
+ * 3. Without changing any other LMC0_DDR_PLL_CTL values,
+ * write LMC0_DDR_PLL_CTL[CLKF] with a value that gives a
+ * desired DDR PLL speed. The LMC0_DDR_PLL_CTL[CLKF] value
+ * should be selected in conjunction with the post-scalar
+ * divider values for LMC (LMC0_DDR_PLL_CTL[DDR_PS_EN]) so
+ * that the desired LMC CK speeds are is produced (all
+ * enabled LMCs must run the same speed). Section 5.14
+ * describes LMC0_DDR_PLL_CTL[CLKF] and
+ * LMC0_DDR_PLL_CTL[DDR_PS_EN] programmings that produce
+ * the desired LMC CK speed. Section 5.9.2 describes LMC CK
+ * initialization, which can be done separately from the DDR
+ * PLL initialization described in this section.
+ *
+ * The LMC0_DDR_PLL_CTL[CLKF] value must not change after
+ * this point without restarting this SDRAM PLL
+ * initialization sequence.
+ */
+
+ /* Init to max error */
+ error = ddr_hertz;
+ best_error = ddr_hertz;
+
+ debug("DDR Reference Hertz = %d\n", ddr_ref_hertz);
+
+ while (best_error == ddr_hertz) {
+ for (clkr = 0; clkr < 4; ++clkr) {
+ for (en_idx =
+ sizeof(_en) / sizeof(int) -
+ 1; en_idx >= 0; --en_idx) {
+ save_en_idx = en_idx;
+ clkf =
+ ((ddr_hertz) *
+ (clkr + 1) * (_en[save_en_idx]));
+ clkf = divide_nint(clkf, ddr_ref_hertz)
+ - 1;
+ pll_MHz =
+ ddr_ref_hertz *
+ (clkf + 1) / (clkr + 1) / 1000000;
+ calculated_ddr_hertz =
+ ddr_ref_hertz *
+ (clkf +
+ 1) / ((clkr +
+ 1) * (_en[save_en_idx]));
+ error =
+ ddr_hertz - calculated_ddr_hertz;
+
+ if (pll_MHz < min_pll_MHz ||
+ pll_MHz > max_pll_MHz)
+ continue;
+ if (clkf > max_clkf) {
+ /*
+ * PLL requires clkf to be
+ * limited
+ */
+ continue;
+ }
+ if (abs(error) > abs(best_error))
+ continue;
+
+ debug("clkr: %2llu, en[%d]: %2d, clkf: %4llu, pll_MHz: %4llu, ddr_hertz: %8llu, error: %8lld\n",
+ clkr, save_en_idx,
+ _en[save_en_idx], clkf, pll_MHz,
+ calculated_ddr_hertz, error);
+
+ /* Favor the highest PLL frequency. */
+ if (abs(error) < abs(best_error) ||
+ pll_MHz > best_pll_MHz) {
+ best_pll_MHz = pll_MHz;
+ best_calculated_ddr_hertz =
+ calculated_ddr_hertz;
+ best_error = error;
+ best_clkr = clkr;
+ best_clkf = clkf;
+ best_en_idx = save_en_idx;
+ }
+ }
+ }
+
+ override_pll_settings = 0;
+
+ s = lookup_env(priv, "ddr_pll_clkr");
+ if (s) {
+ best_clkr = simple_strtoul(s, NULL, 0);
+ override_pll_settings = 1;
+ }
+
+ s = lookup_env(priv, "ddr_pll_clkf");
+ if (s) {
+ best_clkf = simple_strtoul(s, NULL, 0);
+ override_pll_settings = 1;
+ }
+
+ s = lookup_env(priv, "ddr_pll_en_idx");
+ if (s) {
+ best_en_idx = simple_strtoul(s, NULL, 0);
+ override_pll_settings = 1;
+ }
+
+ if (override_pll_settings) {
+ best_pll_MHz =
+ ddr_ref_hertz * (best_clkf +
+ 1) /
+ (best_clkr + 1) / 1000000;
+ best_calculated_ddr_hertz =
+ ddr_ref_hertz * (best_clkf +
+ 1) /
+ ((best_clkr + 1) * (_en[best_en_idx]));
+ best_error =
+ ddr_hertz - best_calculated_ddr_hertz;
+ }
+
+ debug("clkr: %2llu, en[%d]: %2d, clkf: %4llu, pll_MHz: %4llu, ddr_hertz: %8llu, error: %8lld <==\n",
+ best_clkr, best_en_idx, _en[best_en_idx],
+ best_clkf, best_pll_MHz,
+ best_calculated_ddr_hertz, best_error);
+
+ /*
+ * Try lowering the frequency if we can't get a
+ * working configuration
+ */
+ if (best_error == ddr_hertz) {
+ if (ddr_hertz < orig_ddr_hertz - 10000000)
+ break;
+ ddr_hertz -= 1000000;
+ best_error = ddr_hertz;
+ }
+ }
+
+ if (best_error == ddr_hertz) {
+ printf("ERROR: Can not compute a legal DDR clock speed configuration.\n");
+ return -1;
+ }
+
+ new_bwadj = (best_clkf + 1) / 10;
+ debug("bwadj: %2d\n", new_bwadj);
+
+ s = lookup_env(priv, "ddr_pll_bwadj");
+ if (s) {
+ new_bwadj = strtoul(s, NULL, 0);
+ debug("bwadj: %2d\n", new_bwadj);
+ }
+
+ for (i = 0; i < 2; ++i) {
+ if ((if_mask & (1 << i)) == 0)
+ continue;
+
+ ddr_pll_ctl.u64 =
+ lmc_rd(priv, CVMX_LMCX_DDR_PLL_CTL(i));
+ debug("LMC%d: DDR_PLL_CTL : 0x%016llx\n",
+ i, ddr_pll_ctl.u64);
+
+ ddr_pll_ctl.cn78xx.ddr_ps_en = best_en_idx;
+ ddr_pll_ctl.cn78xx.clkf = best_clkf;
+ ddr_pll_ctl.cn78xx.clkr = best_clkr;
+ ddr_pll_ctl.cn78xx.reset_n = 0;
+ ddr_pll_ctl.cn78xx.bwadj = new_bwadj;
+
+ lmc_wr(priv, CVMX_LMCX_DDR_PLL_CTL(i), ddr_pll_ctl.u64);
+ debug("LMC%d: DDR_PLL_CTL : 0x%016llx\n",
+ i, ddr_pll_ctl.u64);
+
+ /*
+ * For cnf75xx LMC0 and LMC1 use the same PLL so
+ * only program LMC0 PLL.
+ */
+ if (octeon_is_cpuid(OCTEON_CNF75XX))
+ break;
+ }
+
+ for (i = 0; i < 4; ++i) {
+ if ((if_mask & (1 << i)) == 0)
+ continue;
+
+ /*
+ * 4. Read LMC0_DDR_PLL_CTL and wait for the result.
+ */
+
+ lmc_rd(priv, CVMX_LMCX_DDR_PLL_CTL(i));
+
+ /*
+ * 5. Wait a minimum of 3 us.
+ */
+
+ udelay(3); /* Wait 3 us */
+
+ /*
+ * 6. Write LMC0_DDR_PLL_CTL[RESET_N] = 1 without
+ * changing any other LMC0_DDR_PLL_CTL values.
+ */
+
+ ddr_pll_ctl.u64 =
+ lmc_rd(priv, CVMX_LMCX_DDR_PLL_CTL(i));
+ ddr_pll_ctl.cn78xx.reset_n = 1;
+ lmc_wr(priv, CVMX_LMCX_DDR_PLL_CTL(i), ddr_pll_ctl.u64);
+
+ /*
+ * 7. Read LMC0_DDR_PLL_CTL and wait for the result.
+ */
+
+ lmc_rd(priv, CVMX_LMCX_DDR_PLL_CTL(i));
+
+ /*
+ * 8. Wait a minimum of 25 us.
+ */
+
+ udelay(25); /* Wait 25 us */
+
+ /*
+ * For cnf75xx LMC0 and LMC1 use the same PLL so
+ * only program LMC0 PLL.
+ */
+ if (octeon_is_cpuid(OCTEON_CNF75XX))
+ break;
+ }
+
+ for (i = 0; i < 4; ++i) {
+ if ((if_mask & (1 << i)) == 0)
+ continue;
+
+ /*
+ * 5.9.2 LMC CK Initialization
+ *
+ * DDR PLL initialization must be completed prior to
+ * starting LMC CK initialization.
+ *
+ * Perform the following substeps to initialize the
+ * LMC CK:
+ *
+ * 1. Without changing any other LMC(0..3)_DDR_PLL_CTL
+ * values, write
+ * LMC(0..3)_DDR_PLL_CTL[DDR_DIV_RESET] = 1 and
+ * LMC(0..3)_DDR_PLL_CTL[DDR_PS_EN] with the
+ * appropriate value to get the desired LMC CK speed.
+ * Section 5.14 discusses CLKF and DDR_PS_EN
+ * programmings. The LMC(0..3)_DDR_PLL_CTL[DDR_PS_EN]
+ * must not change after this point without restarting
+ * this LMC CK initialization sequence.
+ */
+
+ ddr_pll_ctl.u64 = lmc_rd(priv,
+ CVMX_LMCX_DDR_PLL_CTL(i));
+ ddr_pll_ctl.cn78xx.ddr_div_reset = 1;
+ lmc_wr(priv, CVMX_LMCX_DDR_PLL_CTL(i), ddr_pll_ctl.u64);
+
+ /*
+ * 2. Without changing any other fields in
+ * LMC(0..3)_DDR_PLL_CTL, write
+ * LMC(0..3)_DDR_PLL_CTL[DDR4_MODE] = 0.
+ */
+
+ ddr_pll_ctl.u64 =
+ lmc_rd(priv, CVMX_LMCX_DDR_PLL_CTL(i));
+ ddr_pll_ctl.cn78xx.ddr4_mode =
+ (ddr_type == DDR4_DRAM) ? 1 : 0;
+ lmc_wr(priv, CVMX_LMCX_DDR_PLL_CTL(i), ddr_pll_ctl.u64);
+
+ /*
+ * 3. Read LMC(0..3)_DDR_PLL_CTL and wait for the
+ * result.
+ */
+
+ lmc_rd(priv, CVMX_LMCX_DDR_PLL_CTL(i));
+
+ /*
+ * 4. Wait a minimum of 1 us.
+ */
+
+ udelay(1); /* Wait 1 us */
+
+ /*
+ * ###### Steps 5 through 7 deferred until after
+ * DDR_DIV_RESET=0 #######
+ */
+
+ /*
+ * 8. Without changing any other LMC(0..3)_COMP_CTL2
+ * values, write
+ * LMC(0..3)_COMP_CTL2[CK_CTL,CONTROL_CTL,CMD_CTL]
+ * to the desired DDR*_CK_*_P control and command
+ * signals drive strength.
+ */
+
+ union cvmx_lmcx_comp_ctl2 comp_ctl2;
+ const struct ddr3_custom_config *custom_lmc_config =
+ &ddr_conf->custom_lmc_config;
+
+ comp_ctl2.u64 = lmc_rd(priv, CVMX_LMCX_COMP_CTL2(i));
+
+ /* Default 4=34.3 ohm */
+ comp_ctl2.cn78xx.dqx_ctl =
+ (custom_lmc_config->dqx_ctl ==
+ 0) ? 4 : custom_lmc_config->dqx_ctl;
+ /* Default 4=34.3 ohm */
+ comp_ctl2.cn78xx.ck_ctl =
+ (custom_lmc_config->ck_ctl ==
+ 0) ? 4 : custom_lmc_config->ck_ctl;
+ /* Default 4=34.3 ohm */
+ comp_ctl2.cn78xx.cmd_ctl =
+ (custom_lmc_config->cmd_ctl ==
+ 0) ? 4 : custom_lmc_config->cmd_ctl;
+
+ comp_ctl2.cn78xx.rodt_ctl = 0x4; /* 60 ohm */
+
+ comp_ctl2.cn70xx.ptune_offset =
+ (abs(custom_lmc_config->ptune_offset) & 0x7)
+ | (_sign(custom_lmc_config->ptune_offset) << 3);
+ comp_ctl2.cn70xx.ntune_offset =
+ (abs(custom_lmc_config->ntune_offset) & 0x7)
+ | (_sign(custom_lmc_config->ntune_offset) << 3);
+
+ s = lookup_env(priv, "ddr_clk_ctl");
+ if (s) {
+ comp_ctl2.cn78xx.ck_ctl =
+ simple_strtoul(s, NULL, 0);
+ }
+
+ s = lookup_env(priv, "ddr_ck_ctl");
+ if (s) {
+ comp_ctl2.cn78xx.ck_ctl =
+ simple_strtoul(s, NULL, 0);
+ }
+
+ s = lookup_env(priv, "ddr_cmd_ctl");
+ if (s) {
+ comp_ctl2.cn78xx.cmd_ctl =
+ simple_strtoul(s, NULL, 0);
+ }
+
+ s = lookup_env(priv, "ddr_dqx_ctl");
+ if (s) {
+ comp_ctl2.cn78xx.dqx_ctl =
+ simple_strtoul(s, NULL, 0);
+ }
+
+ s = lookup_env(priv, "ddr_ptune_offset");
+ if (s) {
+ comp_ctl2.cn78xx.ptune_offset =
+ simple_strtoul(s, NULL, 0);
+ }
+
+ s = lookup_env(priv, "ddr_ntune_offset");
+ if (s) {
+ comp_ctl2.cn78xx.ntune_offset =
+ simple_strtoul(s, NULL, 0);
+ }
+
+ lmc_wr(priv, CVMX_LMCX_COMP_CTL2(i), comp_ctl2.u64);
+
+ /*
+ * 9. Read LMC(0..3)_DDR_PLL_CTL and wait for the
+ * result.
+ */
+
+ lmc_rd(priv, CVMX_LMCX_DDR_PLL_CTL(i));
+
+ /*
+ * 10. Wait a minimum of 200 ns.
+ */
+
+ udelay(1); /* Wait 1 us */
+
+ /*
+ * 11. Without changing any other
+ * LMC(0..3)_DDR_PLL_CTL values, write
+ * LMC(0..3)_DDR_PLL_CTL[DDR_DIV_RESET] = 0.
+ */
+
+ ddr_pll_ctl.u64 = lmc_rd(priv,
+ CVMX_LMCX_DDR_PLL_CTL(i));
+ ddr_pll_ctl.cn78xx.ddr_div_reset = 0;
+ lmc_wr(priv, CVMX_LMCX_DDR_PLL_CTL(i), ddr_pll_ctl.u64);
+
+ /*
+ * 12. Read LMC(0..3)_DDR_PLL_CTL and wait for the
+ * result.
+ */
+
+ lmc_rd(priv, CVMX_LMCX_DDR_PLL_CTL(i));
+
+ /*
+ * 13. Wait a minimum of 200 ns.
+ */
+
+ udelay(1); /* Wait 1 us */
+ }
+
+ /*
+ * Relocated Interface Enable (intf_en) Step
+ */
+ for (i = (octeon_is_cpuid(OCTEON_CN73XX) ||
+ octeon_is_cpuid(OCTEON_CNF75XX)) ? 1 : 2;
+ i < 4; ++i) {
+ /*
+ * This step is only necessary for LMC 2 and 3 in
+ * 4-LMC mode. The mask will cause the unpopulated
+ * interfaces to be skipped.
+ */
+ if ((if_mask & (1 << i)) == 0)
+ continue;
+
+ dll_ctl2.u64 = lmc_rd(priv, CVMX_LMCX_DLL_CTL2(i));
+ dll_ctl2.cn78xx.intf_en = 1;
+ lmc_wr(priv, CVMX_LMCX_DLL_CTL2(i), dll_ctl2.u64);
+ lmc_rd(priv, CVMX_LMCX_DLL_CTL2(i));
+ }
+
+ /*
+ * Relocated PHY_DCOK Step
+ */
+ for (i = 0; i < 4; ++i) {
+ if ((if_mask & (1 << i)) == 0)
+ continue;
+ /*
+ * 5. Without changing any other fields in
+ * LMC(0..3)_DDR_PLL_CTL, write
+ * LMC(0..3)_DDR_PLL_CTL[PHY_DCOK] = 1.
+ */
+
+ ddr_pll_ctl.u64 = lmc_rd(priv,
+ CVMX_LMCX_DDR_PLL_CTL(i));
+ ddr_pll_ctl.cn78xx.phy_dcok = 1;
+ lmc_wr(priv, CVMX_LMCX_DDR_PLL_CTL(i), ddr_pll_ctl.u64);
+ /*
+ * 6. Read LMC(0..3)_DDR_PLL_CTL and wait for
+ * the result.
+ */
+
+ lmc_rd(priv, CVMX_LMCX_DDR_PLL_CTL(i));
+
+ /*
+ * 7. Wait a minimum of 20 us.
+ */
+
+ udelay(20); /* Wait 20 us */
+ }
+
+ /*
+ * 5.9.4 LMC DRESET Initialization
+ *
+ * All of the DDR PLL, LMC global CK, and LMC interface
+ * enable initializations must be completed prior to starting
+ * this LMC DRESET initialization (Step 4).
+ *
+ * This LMC DRESET step is done for all enabled LMCs.
+ *
+ * There are special constraints on the ordering of DRESET
+ * initialization (Steps 4) and CK local initialization
+ * (Step 5) whenever CK local initialization must be executed.
+ * CK local initialization must be executed whenever the DDR
+ * PLL is being brought up (for each chip reset* and whenever
+ * the DDR clock speed changes).
+ *
+ * When Step 5 must be executed in the two-LMC mode case:
+ * - LMC0 DRESET initialization must occur before Step 5.
+ * - LMC1 DRESET initialization must occur after Step 5.
+ *
+ * When Step 5 must be executed in the four-LMC mode case:
+ * - LMC2 and LMC3 DRESET initialization must occur before
+ * Step 5.
+ * - LMC0 and LMC1 DRESET initialization must occur after
+ * Step 5.
+ */
+
+ if (octeon_is_cpuid(OCTEON_CN73XX)) {
+ /* ONE-LMC or TWO-LMC MODE BEFORE STEP 5 for cn73xx */
+ cn78xx_lmc_dreset_init(priv, 0);
+ } else if (octeon_is_cpuid(OCTEON_CNF75XX)) {
+ if (if_mask == 0x3) {
+ /*
+ * 2-LMC Mode: LMC1 DRESET must occur
+ * before Step 5
+ */
+ cn78xx_lmc_dreset_init(priv, 1);
+ }
+ } else {
+ /* TWO-LMC MODE DRESET BEFORE STEP 5 */
+ if (if_mask == 0x3)
+ cn78xx_lmc_dreset_init(priv, 0);
+
+ /* FOUR-LMC MODE BEFORE STEP 5 */
+ if (if_mask == 0xf) {
+ cn78xx_lmc_dreset_init(priv, 2);
+ cn78xx_lmc_dreset_init(priv, 3);
+ }
+ }
+
+ /*
+ * 5.9.5 LMC CK Local Initialization
+ *
+ * All of DDR PLL, LMC global CK, and LMC interface-enable
+ * initializations must be completed prior to starting this
+ * LMC CK local initialization (Step 5).
+ *
+ * LMC CK Local initialization must be performed for each
+ * chip reset and whenever the DDR clock speed changes. This
+ * step needs to be performed only once, not once per LMC.
+ *
+ * There are special constraints on the ordering of DRESET
+ * initialization (Steps 4) and CK local initialization
+ * (Step 5) whenever CK local initialization must be executed.
+ * CK local initialization must be executed whenever the
+ * DDR PLL is being brought up (for each chip reset and
+ * whenever the DDR clock speed changes).
+ *
+ * When Step 5 must be executed in the two-LMC mode case:
+ * - LMC0 DRESET initialization must occur before Step 5.
+ * - LMC1 DRESET initialization must occur after Step 5.
+ *
+ * When Step 5 must be executed in the four-LMC mode case:
+ * - LMC2 and LMC3 DRESET initialization must occur before
+ * Step 5.
+ * - LMC0 and LMC1 DRESET initialization must occur after
+ * Step 5.
+ *
+ * LMC CK local initialization is different depending on
+ * whether two-LMC or four-LMC modes are desired.
+ */
+
+ if (if_mask == 0x3) {
+ int temp_lmc_if_num = octeon_is_cpuid(OCTEON_CNF75XX) ?
+ 1 : 0;
+
+ /*
+ * 5.9.5.1 LMC CK Local Initialization for Two-LMC
+ * Mode
+ *
+ * 1. Write LMC0_DLL_CTL3 to its reset value. (Note
+ * that LMC0_DLL_CTL3[DLL_90_BYTE_SEL] = 0x2 .. 0x8
+ * should also work.)
+ */
+
+ ddr_dll_ctl3.u64 = 0;
+ ddr_dll_ctl3.cn78xx.dclk90_recal_dis = 1;
+
+ if (octeon_is_cpuid(OCTEON_CNF75XX))
+ ddr_dll_ctl3.cn78xx.dll90_byte_sel = 7;
+ else
+ ddr_dll_ctl3.cn78xx.dll90_byte_sel = 1;
+
+ lmc_wr(priv,
+ CVMX_LMCX_DLL_CTL3(temp_lmc_if_num),
+ ddr_dll_ctl3.u64);
+
+ /*
+ * 2. Read LMC0_DLL_CTL3 and wait for the result.
+ */
+
+ lmc_rd(priv, CVMX_LMCX_DLL_CTL3(temp_lmc_if_num));
+
+ /*
+ * 3. Without changing any other fields in
+ * LMC0_DLL_CTL3, write
+ * LMC0_DLL_CTL3[DCLK90_FWD] = 1. Writing
+ * LMC0_DLL_CTL3[DCLK90_FWD] = 1
+ * causes clock-delay information to be forwarded
+ * from LMC0 to LMC1.
+ */
+
+ ddr_dll_ctl3.cn78xx.dclk90_fwd = 1;
+ lmc_wr(priv,
+ CVMX_LMCX_DLL_CTL3(temp_lmc_if_num),
+ ddr_dll_ctl3.u64);
+
+ /*
+ * 4. Read LMC0_DLL_CTL3 and wait for the result.
+ */
+
+ lmc_rd(priv, CVMX_LMCX_DLL_CTL3(temp_lmc_if_num));
+ }
+
+ if (if_mask == 0xf) {
+ /*
+ * 5.9.5.2 LMC CK Local Initialization for Four-LMC
+ * Mode
+ *
+ * 1. Write LMC2_DLL_CTL3 to its reset value except
+ * LMC2_DLL_CTL3[DLL90_BYTE_SEL] = 0x7.
+ */
+
+ ddr_dll_ctl3.u64 = 0;
+ ddr_dll_ctl3.cn78xx.dclk90_recal_dis = 1;
+ ddr_dll_ctl3.cn78xx.dll90_byte_sel = 7;
+ lmc_wr(priv, CVMX_LMCX_DLL_CTL3(2), ddr_dll_ctl3.u64);
+
+ /*
+ * 2. Write LMC3_DLL_CTL3 to its reset value except
+ * LMC3_DLL_CTL3[DLL90_BYTE_SEL] = 0x2.
+ */
+
+ ddr_dll_ctl3.u64 = 0;
+ ddr_dll_ctl3.cn78xx.dclk90_recal_dis = 1;
+ ddr_dll_ctl3.cn78xx.dll90_byte_sel = 2;
+ lmc_wr(priv, CVMX_LMCX_DLL_CTL3(3), ddr_dll_ctl3.u64);
+
+ /*
+ * 3. Read LMC3_DLL_CTL3 and wait for the result.
+ */
+
+ lmc_rd(priv, CVMX_LMCX_DLL_CTL3(3));
+
+ /*
+ * 4. Without changing any other fields in
+ * LMC2_DLL_CTL3, write LMC2_DLL_CTL3[DCLK90_FWD] = 1
+ * and LMC2_DLL_CTL3[DCLK90_RECAL_ DIS] = 1.
+ * Writing LMC2_DLL_CTL3[DCLK90_FWD] = 1 causes LMC 2
+ * to forward clockdelay information to LMC0. Setting
+ * LMC2_DLL_CTL3[DCLK90_RECAL_DIS] to 1 prevents LMC2
+ * from periodically recalibrating this delay
+ * information.
+ */
+
+ ddr_dll_ctl3.u64 = lmc_rd(priv, CVMX_LMCX_DLL_CTL3(2));
+ ddr_dll_ctl3.cn78xx.dclk90_fwd = 1;
+ ddr_dll_ctl3.cn78xx.dclk90_recal_dis = 1;
+ lmc_wr(priv, CVMX_LMCX_DLL_CTL3(2), ddr_dll_ctl3.u64);
+
+ /*
+ * 5. Without changing any other fields in
+ * LMC3_DLL_CTL3, write LMC3_DLL_CTL3[DCLK90_FWD] = 1
+ * and LMC3_DLL_CTL3[DCLK90_RECAL_ DIS] = 1.
+ * Writing LMC3_DLL_CTL3[DCLK90_FWD] = 1 causes LMC3
+ * to forward clockdelay information to LMC1. Setting
+ * LMC3_DLL_CTL3[DCLK90_RECAL_DIS] to 1 prevents LMC3
+ * from periodically recalibrating this delay
+ * information.
+ */
+
+ ddr_dll_ctl3.u64 = lmc_rd(priv, CVMX_LMCX_DLL_CTL3(3));
+ ddr_dll_ctl3.cn78xx.dclk90_fwd = 1;
+ ddr_dll_ctl3.cn78xx.dclk90_recal_dis = 1;
+ lmc_wr(priv, CVMX_LMCX_DLL_CTL3(3), ddr_dll_ctl3.u64);
+
+ /*
+ * 6. Read LMC3_DLL_CTL3 and wait for the result.
+ */
+
+ lmc_rd(priv, CVMX_LMCX_DLL_CTL3(3));
+ }
+
+ if (octeon_is_cpuid(OCTEON_CNF75XX)) {
+ /*
+ * cnf75xx 2-LMC Mode: LMC0 DRESET must occur after
+ * Step 5, Do LMC0 for 1-LMC Mode here too
+ */
+ cn78xx_lmc_dreset_init(priv, 0);
+ }
+
+ /* TWO-LMC MODE AFTER STEP 5 */
+ if (if_mask == 0x3) {
+ if (octeon_is_cpuid(OCTEON_CNF75XX)) {
+ /*
+ * cnf75xx 2-LMC Mode: LMC0 DRESET must
+ * occur after Step 5
+ */
+ cn78xx_lmc_dreset_init(priv, 0);
+ } else {
+ cn78xx_lmc_dreset_init(priv, 1);
+ }
+ }
+
+ /* FOUR-LMC MODE AFTER STEP 5 */
+ if (if_mask == 0xf) {
+ cn78xx_lmc_dreset_init(priv, 0);
+ cn78xx_lmc_dreset_init(priv, 1);
+
+ /*
+ * Enable periodic recalibration of DDR90 delay
+ * line in.
+ */
+ ddr_dll_ctl3.u64 = lmc_rd(priv, CVMX_LMCX_DLL_CTL3(0));
+ ddr_dll_ctl3.cn78xx.dclk90_recal_dis = 0;
+ lmc_wr(priv, CVMX_LMCX_DLL_CTL3(0), ddr_dll_ctl3.u64);
+ ddr_dll_ctl3.u64 = lmc_rd(priv, CVMX_LMCX_DLL_CTL3(1));
+ ddr_dll_ctl3.cn78xx.dclk90_recal_dis = 0;
+ lmc_wr(priv, CVMX_LMCX_DLL_CTL3(1), ddr_dll_ctl3.u64);
+ }
+
+ /* Enable fine tune mode for all LMCs */
+ for (i = 0; i < 4; ++i) {
+ if ((if_mask & (1 << i)) == 0)
+ continue;
+ ddr_dll_ctl3.u64 = lmc_rd(priv, CVMX_LMCX_DLL_CTL3(i));
+ ddr_dll_ctl3.cn78xx.fine_tune_mode = 1;
+ lmc_wr(priv, CVMX_LMCX_DLL_CTL3(i), ddr_dll_ctl3.u64);
+ }
+
+ /*
+ * Enable the trim circuit on the appropriate channels to
+ * adjust the DDR clock duty cycle for chips that support
+ * it
+ */
+ if (octeon_is_cpuid(OCTEON_CN78XX_PASS2_X) ||
+ octeon_is_cpuid(OCTEON_CN73XX) ||
+ octeon_is_cpuid(OCTEON_CNF75XX)) {
+ union cvmx_lmcx_phy_ctl lmc_phy_ctl;
+ int i;
+
+ for (i = 0; i < 4; ++i) {
+ if ((if_mask & (1 << i)) == 0)
+ continue;
+
+ lmc_phy_ctl.u64 =
+ lmc_rd(priv, CVMX_LMCX_PHY_CTL(i));
+
+ if (octeon_is_cpuid(OCTEON_CNF75XX) ||
+ octeon_is_cpuid(OCTEON_CN73XX_PASS1_3)) {
+ /* Both LMCs */
+ lmc_phy_ctl.s.lv_mode = 0;
+ } else {
+ /* Odd LMCs = 0, Even LMCs = 1 */
+ lmc_phy_ctl.s.lv_mode = (~i) & 1;
+ }
+
+ debug("LMC%d: PHY_CTL : 0x%016llx\n",
+ i, lmc_phy_ctl.u64);
+ lmc_wr(priv, CVMX_LMCX_PHY_CTL(i),
+ lmc_phy_ctl.u64);
+ }
+ }
+ }
+
+ /*
+ * 5.9.6 LMC RESET Initialization
+ *
+ * NOTE: this is now done as the first step in
+ * init_octeon3_ddr3_interface, rather than the last step in clock
+ * init. This reorg allows restarting per-LMC initialization should
+ * problems be encountered, rather than being forced to resort to
+ * resetting the chip and starting all over.
+ *
+ * Look for the code in octeon3_lmc.c: perform_lmc_reset().
+ */
+
+ /* Fallthrough for all interfaces... */
+not_if0:
+
+ /*
+ * Start the DDR clock so that its frequency can be measured.
+ * For some chips we must activate the memory controller with
+ * init_start to make the DDR clock start to run.
+ */
+ if ((!octeon_is_cpuid(OCTEON_CN6XXX)) &&
+ (!octeon_is_cpuid(OCTEON_CN56XX)) &&
+ (!octeon_is_cpuid(OCTEON_CNF7XXX)) &&
+ (!octeon_is_cpuid(OCTEON_CN7XXX))) {
+ union cvmx_lmcx_mem_cfg0 mem_cfg0;
+
+ mem_cfg0.u64 = 0;
+ mem_cfg0.s.init_start = 1;
+ lmc_wr(priv, CVMX_LMCX_MEM_CFG0(if_num), mem_cfg0.u64);
+ lmc_rd(priv, CVMX_LMCX_MEM_CFG0(if_num));
+ }
+
+ set_ddr_clock_initialized(priv, if_num, 1);
+
+ return 0;
+}
+
+static void octeon_ipd_delay_cycles(u64 cycles)
+{
+ u64 start = csr_rd(CVMX_IPD_CLK_COUNT);
+
+ while (start + cycles > csr_rd(CVMX_IPD_CLK_COUNT))
+ ;
+}
+
+static void octeon_ipd_delay_cycles_o3(u64 cycles)
+{
+ u64 start = csr_rd(CVMX_FPA_CLK_COUNT);
+
+ while (start + cycles > csr_rd(CVMX_FPA_CLK_COUNT))
+ ;
+}
+
+static u32 measure_octeon_ddr_clock(struct ddr_priv *priv,
+ struct ddr_conf *ddr_conf, u32 cpu_hertz,
+ u32 ddr_hertz, u32 ddr_ref_hertz,
+ int if_num, u32 if_mask)
+{
+ u64 core_clocks;
+ u64 ddr_clocks;
+ u64 calc_ddr_hertz;
+
+ if (ddr_conf) {
+ if (initialize_ddr_clock(priv, ddr_conf, cpu_hertz,
+ ddr_hertz, ddr_ref_hertz, if_num,
+ if_mask) != 0)
+ return 0;
+ }
+
+ /* Dynamically determine the DDR clock speed */
+ if (OCTEON_IS_OCTEON2() || octeon_is_cpuid(OCTEON_CN70XX)) {
+ core_clocks = csr_rd(CVMX_IPD_CLK_COUNT);
+ ddr_clocks = lmc_rd(priv, CVMX_LMCX_DCLK_CNT(if_num));
+ /* How many cpu cycles to measure over */
+ octeon_ipd_delay_cycles(100000000);
+ core_clocks = csr_rd(CVMX_IPD_CLK_COUNT) - core_clocks;
+ ddr_clocks =
+ lmc_rd(priv, CVMX_LMCX_DCLK_CNT(if_num)) - ddr_clocks;
+ calc_ddr_hertz = ddr_clocks * gd->bus_clk / core_clocks;
+ } else if (octeon_is_cpuid(OCTEON_CN7XXX)) {
+ core_clocks = csr_rd(CVMX_FPA_CLK_COUNT);
+ ddr_clocks = lmc_rd(priv, CVMX_LMCX_DCLK_CNT(if_num));
+ /* How many cpu cycles to measure over */
+ octeon_ipd_delay_cycles_o3(100000000);
+ core_clocks = csr_rd(CVMX_FPA_CLK_COUNT) - core_clocks;
+ ddr_clocks =
+ lmc_rd(priv, CVMX_LMCX_DCLK_CNT(if_num)) - ddr_clocks;
+ calc_ddr_hertz = ddr_clocks * gd->bus_clk / core_clocks;
+ } else {
+ core_clocks = csr_rd(CVMX_IPD_CLK_COUNT);
+ /*
+ * ignore overflow, starts counting when we enable the
+ * controller
+ */
+ ddr_clocks = lmc_rd(priv, CVMX_LMCX_DCLK_CNT_LO(if_num));
+ /* How many cpu cycles to measure over */
+ octeon_ipd_delay_cycles(100000000);
+ core_clocks = csr_rd(CVMX_IPD_CLK_COUNT) - core_clocks;
+ ddr_clocks =
+ lmc_rd(priv, CVMX_LMCX_DCLK_CNT_LO(if_num)) - ddr_clocks;
+ calc_ddr_hertz = ddr_clocks * cpu_hertz / core_clocks;
+ }
+
+ debug("core clocks: %llu, ddr clocks: %llu, calc rate: %llu\n",
+ core_clocks, ddr_clocks, calc_ddr_hertz);
+ debug("LMC%d: Measured DDR clock: %lld, cpu clock: %u, ddr clocks: %llu\n",
+ if_num, calc_ddr_hertz, cpu_hertz, ddr_clocks);
+
+ /* Check for unreasonable settings. */
+ if (calc_ddr_hertz < 10000) {
+ udelay(8000000 * 100);
+ printf("DDR clock misconfigured on interface %d. Resetting...\n",
+ if_num);
+ do_reset(NULL, 0, 0, NULL);
+ }
+
+ return calc_ddr_hertz;
+}
+
+u64 lmc_ddr3_rl_dbg_read(struct ddr_priv *priv, int if_num, int idx)
+{
+ union cvmx_lmcx_rlevel_dbg rlevel_dbg;
+ union cvmx_lmcx_rlevel_ctl rlevel_ctl;
+
+ rlevel_ctl.u64 = lmc_rd(priv, CVMX_LMCX_RLEVEL_CTL(if_num));
+ rlevel_ctl.s.byte = idx;
+
+ lmc_wr(priv, CVMX_LMCX_RLEVEL_CTL(if_num), rlevel_ctl.u64);
+ lmc_rd(priv, CVMX_LMCX_RLEVEL_CTL(if_num));
+
+ rlevel_dbg.u64 = lmc_rd(priv, CVMX_LMCX_RLEVEL_DBG(if_num));
+ return rlevel_dbg.s.bitmask;
+}
+
+u64 lmc_ddr3_wl_dbg_read(struct ddr_priv *priv, int if_num, int idx)
+{
+ union cvmx_lmcx_wlevel_dbg wlevel_dbg;
+
+ wlevel_dbg.u64 = 0;
+ wlevel_dbg.s.byte = idx;
+
+ lmc_wr(priv, CVMX_LMCX_WLEVEL_DBG(if_num), wlevel_dbg.u64);
+ lmc_rd(priv, CVMX_LMCX_WLEVEL_DBG(if_num));
+
+ wlevel_dbg.u64 = lmc_rd(priv, CVMX_LMCX_WLEVEL_DBG(if_num));
+ return wlevel_dbg.s.bitmask;
+}
+
+int validate_ddr3_rlevel_bitmask(struct rlevel_bitmask *rlevel_bitmask_p,
+ int ddr_type)
+{
+ int i;
+ int errors = 0;
+ u64 mask = 0; /* Used in 64-bit comparisons */
+ u8 mstart = 0;
+ u8 width = 0;
+ u8 firstbit = 0;
+ u8 lastbit = 0;
+ u8 bubble = 0;
+ u8 tbubble = 0;
+ u8 blank = 0;
+ u8 narrow = 0;
+ u8 trailing = 0;
+ u64 bitmask = rlevel_bitmask_p->bm;
+ u8 extras = 0;
+ u8 toolong = 0;
+ u64 temp;
+
+ if (bitmask == 0) {
+ blank += RLEVEL_BITMASK_BLANK_ERROR;
+ } else {
+ /* Look for fb, the first bit */
+ temp = bitmask;
+ while (!(temp & 1)) {
+ firstbit++;
+ temp >>= 1;
+ }
+
+ /* Look for lb, the last bit */
+ lastbit = firstbit;
+ while ((temp >>= 1))
+ lastbit++;
+
+ /*
+ * Start with the max range to try to find the largest mask
+ * within the bitmask data
+ */
+ width = MASKRANGE_BITS;
+ for (mask = MASKRANGE; mask > 0; mask >>= 1, --width) {
+ for (mstart = lastbit - width + 1; mstart >= firstbit;
+ --mstart) {
+ temp = mask << mstart;
+ if ((bitmask & temp) == temp)
+ goto done_now;
+ }
+ }
+done_now:
+ /* look for any more contiguous 1's to the right of mstart */
+ if (width == MASKRANGE_BITS) { // only when maximum mask
+ while ((bitmask >> (mstart - 1)) & 1) {
+ // slide right over more 1's
+ --mstart;
+ // count the number of extra bits only for DDR4
+ if (ddr_type == DDR4_DRAM)
+ extras++;
+ }
+ }
+
+ /* Penalize any extra 1's beyond the maximum desired mask */
+ if (extras > 0)
+ toolong =
+ RLEVEL_BITMASK_TOOLONG_ERROR * ((1 << extras) - 1);
+
+ /* Detect if bitmask is too narrow. */
+ if (width < 4)
+ narrow = (4 - width) * RLEVEL_BITMASK_NARROW_ERROR;
+
+ /*
+ * detect leading bubble bits, that is, any 0's between first
+ * and mstart
+ */
+ temp = bitmask >> (firstbit + 1);
+ i = mstart - firstbit - 1;
+ while (--i >= 0) {
+ if ((temp & 1) == 0)
+ bubble += RLEVEL_BITMASK_BUBBLE_BITS_ERROR;
+ temp >>= 1;
+ }
+
+ temp = bitmask >> (mstart + width + extras);
+ i = lastbit - (mstart + width + extras - 1);
+ while (--i >= 0) {
+ if (temp & 1) {
+ /*
+ * Detect 1 bits after the trailing end of
+ * the mask, including last.
+ */
+ trailing += RLEVEL_BITMASK_TRAILING_BITS_ERROR;
+ } else {
+ /*
+ * Detect trailing bubble bits, that is,
+ * any 0's between end-of-mask and last
+ */
+ tbubble += RLEVEL_BITMASK_BUBBLE_BITS_ERROR;
+ }
+ temp >>= 1;
+ }
+ }
+
+ errors = bubble + tbubble + blank + narrow + trailing + toolong;
+
+ /* Pass out useful statistics */
+ rlevel_bitmask_p->mstart = mstart;
+ rlevel_bitmask_p->width = width;
+
+ debug_bitmask_print("bm:%08lx mask:%02lx, width:%2u, mstart:%2d, fb:%2u, lb:%2u (bu:%2d, tb:%2d, bl:%2d, n:%2d, t:%2d, x:%2d) errors:%3d %s\n",
+ (unsigned long)bitmask, mask, width, mstart,
+ firstbit, lastbit, bubble, tbubble, blank,
+ narrow, trailing, toolong, errors,
+ (errors) ? "=> invalid" : "");
+
+ return errors;
+}
+
+int compute_ddr3_rlevel_delay(u8 mstart, u8 width,
+ union cvmx_lmcx_rlevel_ctl rlevel_ctl)
+{
+ int delay;
+
+ debug_bitmask_print(" offset_en:%d", rlevel_ctl.s.offset_en);
+
+ if (rlevel_ctl.s.offset_en) {
+ delay = max((int)mstart,
+ (int)(mstart + width - 1 - rlevel_ctl.s.offset));
+ } else {
+ /* if (rlevel_ctl.s.offset) { *//* Experimental */
+ if (0) {
+ delay = max(mstart + rlevel_ctl.s.offset, mstart + 1);
+ /*
+ * Insure that the offset delay falls within the
+ * bitmask
+ */
+ delay = min(delay, mstart + width - 1);
+ } else {
+ /* Round down */
+ delay = (width - 1) / 2 + mstart;
+ }
+ }
+
+ return delay;
+}
+
+/* Default ODT config must disable ODT */
+/* Must be const (read only) so that the structure is in flash */
+const struct dimm_odt_config disable_odt_config[] = {
+ /* 1 */ { 0, 0x0000, {.u64 = 0x0000}, {.u64 = 0x0000}, 0, 0x0000, 0 },
+ /* 2 */ { 0, 0x0000, {.u64 = 0x0000}, {.u64 = 0x0000}, 0, 0x0000, 0 },
+ /* 3 */ { 0, 0x0000, {.u64 = 0x0000}, {.u64 = 0x0000}, 0, 0x0000, 0 },
+ /* 4 */ { 0, 0x0000, {.u64 = 0x0000}, {.u64 = 0x0000}, 0, 0x0000, 0 },
+};
+
+/* Memory controller setup function */
+static int init_octeon_dram_interface(struct ddr_priv *priv,
+ struct ddr_conf *ddr_conf,
+ u32 ddr_hertz, u32 cpu_hertz,
+ u32 ddr_ref_hertz, int if_num,
+ u32 if_mask)
+{
+ u32 mem_size_mbytes = 0;
+ char *s;
+
+ s = lookup_env(priv, "ddr_timing_hertz");
+ if (s)
+ ddr_hertz = simple_strtoul(s, NULL, 0);
+
+ if (OCTEON_IS_OCTEON3()) {
+ int lmc_restart_retries = 0;
+#define DEFAULT_RESTART_RETRIES 3
+ int lmc_restart_retries_limit = DEFAULT_RESTART_RETRIES;
+
+ s = lookup_env(priv, "ddr_restart_retries_limit");
+ if (s)
+ lmc_restart_retries_limit = simple_strtoul(s, NULL, 0);
+
+restart_lmc_init:
+ mem_size_mbytes = init_octeon3_ddr3_interface(priv, ddr_conf,
+ ddr_hertz,
+ cpu_hertz,
+ ddr_ref_hertz,
+ if_num, if_mask);
+ if (mem_size_mbytes == 0) { // 0 means restart is possible
+ if (lmc_restart_retries < lmc_restart_retries_limit) {
+ lmc_restart_retries++;
+ printf("N0.LMC%d Configuration problem: attempting LMC reset and init restart %d\n",
+ if_num, lmc_restart_retries);
+ goto restart_lmc_init;
+ } else {
+ if (lmc_restart_retries_limit > 0) {
+ printf("INFO: N0.LMC%d Configuration: fatal problem remains after %d LMC init retries - Resetting node...\n",
+ if_num, lmc_restart_retries);
+ mdelay(500);
+ do_reset(NULL, 0, 0, NULL);
+ } else {
+ // return an error, no restart
+ mem_size_mbytes = -1;
+ }
+ }
+ }
+ }
+
+ debug("N0.LMC%d Configuration Completed: %d MB\n",
+ if_num, mem_size_mbytes);
+
+ return mem_size_mbytes;
+}
+
+#define WLEVEL_BYTE_BITS 5
+#define WLEVEL_BYTE_MSK ((1ULL << 5) - 1)
+
+void upd_wl_rank(union cvmx_lmcx_wlevel_rankx *lmc_wlevel_rank,
+ int byte, int delay)
+{
+ union cvmx_lmcx_wlevel_rankx temp_wlevel_rank;
+
+ if (byte >= 0 && byte <= 8) {
+ temp_wlevel_rank.u64 = lmc_wlevel_rank->u64;
+ temp_wlevel_rank.u64 &=
+ ~(WLEVEL_BYTE_MSK << (WLEVEL_BYTE_BITS * byte));
+ temp_wlevel_rank.u64 |=
+ ((delay & WLEVEL_BYTE_MSK) << (WLEVEL_BYTE_BITS * byte));
+ lmc_wlevel_rank->u64 = temp_wlevel_rank.u64;
+ }
+}
+
+int get_wl_rank(union cvmx_lmcx_wlevel_rankx *lmc_wlevel_rank, int byte)
+{
+ int delay = 0;
+
+ if (byte >= 0 && byte <= 8)
+ delay =
+ ((lmc_wlevel_rank->u64) >> (WLEVEL_BYTE_BITS *
+ byte)) & WLEVEL_BYTE_MSK;
+
+ return delay;
+}
+
+void upd_rl_rank(union cvmx_lmcx_rlevel_rankx *lmc_rlevel_rank,
+ int byte, int delay)
+{
+ union cvmx_lmcx_rlevel_rankx temp_rlevel_rank;
+
+ if (byte >= 0 && byte <= 8) {
+ temp_rlevel_rank.u64 =
+ lmc_rlevel_rank->u64 & ~(RLEVEL_BYTE_MSK <<
+ (RLEVEL_BYTE_BITS * byte));
+ temp_rlevel_rank.u64 |=
+ ((delay & RLEVEL_BYTE_MSK) << (RLEVEL_BYTE_BITS * byte));
+ lmc_rlevel_rank->u64 = temp_rlevel_rank.u64;
+ }
+}
+
+int get_rl_rank(union cvmx_lmcx_rlevel_rankx *lmc_rlevel_rank, int byte)
+{
+ int delay = 0;
+
+ if (byte >= 0 && byte <= 8)
+ delay =
+ ((lmc_rlevel_rank->u64) >> (RLEVEL_BYTE_BITS *
+ byte)) & RLEVEL_BYTE_MSK;
+
+ return delay;
+}
+
+void rlevel_to_wlevel(union cvmx_lmcx_rlevel_rankx *lmc_rlevel_rank,
+ union cvmx_lmcx_wlevel_rankx *lmc_wlevel_rank, int byte)
+{
+ int byte_delay = get_rl_rank(lmc_rlevel_rank, byte);
+
+ debug("Estimating Wlevel delay byte %d: ", byte);
+ debug("Rlevel=%d => ", byte_delay);
+ byte_delay = divide_roundup(byte_delay, 2) & 0x1e;
+ debug("Wlevel=%d\n", byte_delay);
+ upd_wl_rank(lmc_wlevel_rank, byte, byte_delay);
+}
+
+/* Delay trend: constant=0, decreasing=-1, increasing=1 */
+static s64 calc_delay_trend(s64 v)
+{
+ if (v == 0)
+ return 0;
+ if (v < 0)
+ return -1;
+
+ return 1;
+}
+
+/*
+ * Evaluate delay sequence across the whole range of byte delays while
+ * keeping track of the overall delay trend, increasing or decreasing.
+ * If the trend changes charge an error amount to the score.
+ */
+
+// NOTE: "max_adj_delay_inc" argument is, by default, 1 for DDR3 and 2 for DDR4
+
+int nonseq_del(struct rlevel_byte_data *rlevel_byte, int start, int end,
+ int max_adj_delay_inc)
+{
+ s64 error = 0;
+ s64 delay_trend, prev_trend = 0;
+ int byte_idx;
+ s64 seq_err;
+ s64 adj_err;
+ s64 delay_inc;
+ s64 delay_diff;
+
+ for (byte_idx = start; byte_idx < end; ++byte_idx) {
+ delay_diff = rlevel_byte[byte_idx + 1].delay -
+ rlevel_byte[byte_idx].delay;
+ delay_trend = calc_delay_trend(delay_diff);
+
+ /*
+ * Increment error each time the trend changes to the
+ * opposite direction.
+ */
+ if (prev_trend != 0 && delay_trend != 0 &&
+ prev_trend != delay_trend) {
+ seq_err = RLEVEL_NONSEQUENTIAL_DELAY_ERROR;
+ } else {
+ seq_err = 0;
+ }
+
+ // how big was the delay change, if any
+ delay_inc = abs(delay_diff);
+
+ /*
+ * Even if the trend did not change to the opposite direction,
+ * check for the magnitude of the change, and scale the
+ * penalty by the amount that the size is larger than the
+ * provided limit.
+ */
+ if (max_adj_delay_inc != 0 && delay_inc > max_adj_delay_inc) {
+ adj_err = (delay_inc - max_adj_delay_inc) *
+ RLEVEL_ADJACENT_DELAY_ERROR;
+ } else {
+ adj_err = 0;
+ }
+
+ rlevel_byte[byte_idx + 1].sqerrs = seq_err + adj_err;
+ error += seq_err + adj_err;
+
+ debug_bitmask_print("Byte %d: %d, Byte %d: %d, delay_trend: %ld, prev_trend: %ld, [%ld/%ld]%s%s\n",
+ byte_idx + 0,
+ rlevel_byte[byte_idx + 0].delay,
+ byte_idx + 1,
+ rlevel_byte[byte_idx + 1].delay,
+ delay_trend,
+ prev_trend, seq_err, adj_err,
+ (seq_err) ?
+ " => Nonsequential byte delay" : "",
+ (adj_err) ?
+ " => Adjacent delay error" : "");
+
+ if (delay_trend != 0)
+ prev_trend = delay_trend;
+ }
+
+ return (int)error;
+}
+
+int roundup_ddr3_wlevel_bitmask(int bitmask)
+{
+ int shifted_bitmask;
+ int leader;
+ int delay;
+
+ for (leader = 0; leader < 8; ++leader) {
+ shifted_bitmask = (bitmask >> leader);
+ if ((shifted_bitmask & 1) == 0)
+ break;
+ }
+
+ for (leader = leader; leader < 16; ++leader) {
+ shifted_bitmask = (bitmask >> (leader % 8));
+ if (shifted_bitmask & 1)
+ break;
+ }
+
+ delay = (leader & 1) ? leader + 1 : leader;
+ delay = delay % 8;
+
+ return delay;
+}
+
+/* Octeon 2 */
+static void oct2_ddr3_seq(struct ddr_priv *priv, int rank_mask, int if_num,
+ int sequence)
+{
+ char *s;
+
+#ifdef DEBUG_PERFORM_DDR3_SEQUENCE
+ static const char * const sequence_str[] = {
+ "power-up/init",
+ "read-leveling",
+ "self-refresh entry",
+ "self-refresh exit",
+ "precharge power-down entry",
+ "precharge power-down exit",
+ "write-leveling",
+ "illegal"
+ };
+#endif
+
+ union cvmx_lmcx_control lmc_control;
+ union cvmx_lmcx_config lmc_config;
+ int save_ddr2t;
+
+ lmc_control.u64 = lmc_rd(priv, CVMX_LMCX_CONTROL(if_num));
+ save_ddr2t = lmc_control.s.ddr2t;
+
+ if (save_ddr2t == 0 && octeon_is_cpuid(OCTEON_CN63XX_PASS1_X)) {
+ /* Some register parts (IDT and TI included) do not like
+ * the sequence that LMC generates for an MRS register
+ * write in 1T mode. In this case, the register part does
+ * not properly forward the MRS register write to the DRAM
+ * parts. See errata (LMC-14548) Issues with registered
+ * DIMMs.
+ */
+ debug("Forcing DDR 2T during init seq. Re: Pass 1 LMC-14548\n");
+ lmc_control.s.ddr2t = 1;
+ }
+
+ s = lookup_env(priv, "ddr_init_2t");
+ if (s)
+ lmc_control.s.ddr2t = simple_strtoul(s, NULL, 0);
+
+ lmc_wr(priv, CVMX_LMCX_CONTROL(if_num), lmc_control.u64);
+
+ lmc_config.u64 = lmc_rd(priv, CVMX_LMCX_CONFIG(if_num));
+
+ lmc_config.s.init_start = 1;
+ if (OCTEON_IS_OCTEON2())
+ lmc_config.cn63xx.sequence = sequence;
+ lmc_config.s.rankmask = rank_mask;
+
+#ifdef DEBUG_PERFORM_DDR3_SEQUENCE
+ debug("Performing LMC sequence: rank_mask=0x%02x, sequence=%d, %s\n",
+ rank_mask, sequence, sequence_str[sequence]);
+#endif
+
+ lmc_wr(priv, CVMX_LMCX_CONFIG(if_num), lmc_config.u64);
+ lmc_rd(priv, CVMX_LMCX_CONFIG(if_num));
+ udelay(600); /* Wait a while */
+
+ lmc_control.s.ddr2t = save_ddr2t;
+ lmc_wr(priv, CVMX_LMCX_CONTROL(if_num), lmc_control.u64);
+ lmc_rd(priv, CVMX_LMCX_CONTROL(if_num));
+}
+
+/* Check to see if any custom offset values are used */
+static int is_dll_offset_provided(const int8_t *dll_offset_table)
+{
+ int i;
+
+ if (!dll_offset_table) /* Check for pointer to table. */
+ return 0;
+
+ for (i = 0; i < 9; ++i) {
+ if (dll_offset_table[i] != 0)
+ return 1;
+ }
+
+ return 0;
+}
+
+void change_dll_offset_enable(struct ddr_priv *priv, int if_num, int change)
+{
+ union cvmx_lmcx_dll_ctl3 ddr_dll_ctl3;
+
+ ddr_dll_ctl3.u64 = lmc_rd(priv, CVMX_LMCX_DLL_CTL3(if_num));
+ SET_DDR_DLL_CTL3(offset_ena, !!change);
+ lmc_wr(priv, CVMX_LMCX_DLL_CTL3(if_num), ddr_dll_ctl3.u64);
+ ddr_dll_ctl3.u64 = lmc_rd(priv, CVMX_LMCX_DLL_CTL3(if_num));
+}
+
+unsigned short load_dll_offset(struct ddr_priv *priv, int if_num,
+ int dll_offset_mode, int byte_offset, int byte)
+{
+ union cvmx_lmcx_dll_ctl3 ddr_dll_ctl3;
+ int field_width = 6;
+ /*
+ * byte_sel:
+ * 0x1 = byte 0, ..., 0x9 = byte 8
+ * 0xA = all bytes
+ */
+ int byte_sel = (byte == 10) ? byte : byte + 1;
+
+ if (octeon_is_cpuid(OCTEON_CN6XXX))
+ field_width = 5;
+
+ ddr_dll_ctl3.u64 = lmc_rd(priv, CVMX_LMCX_DLL_CTL3(if_num));
+ SET_DDR_DLL_CTL3(load_offset, 0);
+ lmc_wr(priv, CVMX_LMCX_DLL_CTL3(if_num), ddr_dll_ctl3.u64);
+ ddr_dll_ctl3.u64 = lmc_rd(priv, CVMX_LMCX_DLL_CTL3(if_num));
+
+ SET_DDR_DLL_CTL3(mode_sel, dll_offset_mode);
+ SET_DDR_DLL_CTL3(offset,
+ (abs(byte_offset) & (~(-1 << field_width))) |
+ (_sign(byte_offset) << field_width));
+ SET_DDR_DLL_CTL3(byte_sel, byte_sel);
+ lmc_wr(priv, CVMX_LMCX_DLL_CTL3(if_num), ddr_dll_ctl3.u64);
+ ddr_dll_ctl3.u64 = lmc_rd(priv, CVMX_LMCX_DLL_CTL3(if_num));
+
+ SET_DDR_DLL_CTL3(load_offset, 1);
+ lmc_wr(priv, CVMX_LMCX_DLL_CTL3(if_num), ddr_dll_ctl3.u64);
+ ddr_dll_ctl3.u64 = lmc_rd(priv, CVMX_LMCX_DLL_CTL3(if_num));
+
+ return (unsigned short)GET_DDR_DLL_CTL3(offset);
+}
+
+void process_custom_dll_offsets(struct ddr_priv *priv, int if_num,
+ const char *enable_str,
+ const int8_t *offsets, const char *byte_str,
+ int mode)
+{
+ const char *s;
+ int enabled;
+ int provided;
+ int byte_offset;
+ unsigned short offset[9] = { 0 };
+ int byte;
+
+ s = lookup_env(priv, enable_str);
+ if (s)
+ enabled = !!simple_strtol(s, NULL, 0);
+ else
+ enabled = -1;
+
+ /*
+ * enabled == -1: no override, do only configured offsets if provided
+ * enabled == 0: override OFF, do NOT do it even if configured
+ * offsets provided
+ * enabled == 1: override ON, do it for overrides plus configured
+ * offsets
+ */
+
+ if (enabled == 0)
+ return;
+
+ provided = is_dll_offset_provided(offsets);
+
+ if (enabled < 0 && !provided)
+ return;
+
+ change_dll_offset_enable(priv, if_num, 0);
+
+ for (byte = 0; byte < 9; ++byte) {
+ // always take the provided, if available
+ byte_offset = (provided) ? offsets[byte] : 0;
+
+ // then, if enabled, use any overrides present
+ if (enabled > 0) {
+ s = lookup_env(priv, byte_str, if_num, byte);
+ if (s)
+ byte_offset = simple_strtol(s, NULL, 0);
+ }
+
+ offset[byte] =
+ load_dll_offset(priv, if_num, mode, byte_offset, byte);
+ }
+
+ change_dll_offset_enable(priv, if_num, 1);
+
+ debug("N0.LMC%d: DLL %s Offset 8:0 : 0x%02x 0x%02x 0x%02x 0x%02x 0x%02x 0x%02x 0x%02x 0x%02x 0x%02x\n",
+ if_num, (mode == 2) ? "Read " : "Write",
+ offset[8], offset[7], offset[6], offset[5], offset[4],
+ offset[3], offset[2], offset[1], offset[0]);
+}
+
+void ddr_init_seq(struct ddr_priv *priv, int rank_mask, int if_num)
+{
+ char *s;
+ int ddr_init_loops = 1;
+ int rankx;
+
+ s = lookup_env(priv, "ddr%d_init_loops", if_num);
+ if (s)
+ ddr_init_loops = simple_strtoul(s, NULL, 0);
+
+ while (ddr_init_loops--) {
+ for (rankx = 0; rankx < 8; rankx++) {
+ if (!(rank_mask & (1 << rankx)))
+ continue;
+
+ if (OCTEON_IS_OCTEON3()) {
+ /* power-up/init */
+ oct3_ddr3_seq(priv, 1 << rankx, if_num, 0);
+ } else {
+ /* power-up/init */
+ oct2_ddr3_seq(priv, 1 << rankx, if_num, 0);
+ }
+
+ udelay(1000); /* Wait a while. */
+
+ s = lookup_env(priv, "ddr_sequence1");
+ if (s) {
+ int sequence1;
+
+ sequence1 = simple_strtoul(s, NULL, 0);
+
+ if (OCTEON_IS_OCTEON3()) {
+ oct3_ddr3_seq(priv, 1 << rankx,
+ if_num, sequence1);
+ } else {
+ oct2_ddr3_seq(priv, 1 << rankx,
+ if_num, sequence1);
+ }
+ }
+
+ s = lookup_env(priv, "ddr_sequence2");
+ if (s) {
+ int sequence2;
+
+ sequence2 = simple_strtoul(s, NULL, 0);
+
+ if (OCTEON_IS_OCTEON3())
+ oct3_ddr3_seq(priv, 1 << rankx,
+ if_num, sequence2);
+ else
+ oct2_ddr3_seq(priv, 1 << rankx,
+ if_num, sequence2);
+ }
+ }
+ }
+}
+
+static int octeon_ddr_initialize(struct ddr_priv *priv, u32 cpu_hertz,
+ u32 ddr_hertz, u32 ddr_ref_hertz,
+ u32 if_mask,
+ struct ddr_conf *ddr_conf,
+ u32 *measured_ddr_hertz)
+{
+ u32 ddr_conf_valid_mask = 0;
+ int memsize_mbytes = 0;
+ char *eptr;
+ int if_idx;
+ u32 ddr_max_speed = 667000000;
+ u32 calc_ddr_hertz = -1;
+ int val;
+ int ret;
+
+ if (env_get("ddr_verbose") || env_get("ddr_prompt"))
+ priv->flags |= FLAG_DDR_VERBOSE;
+
+#ifdef DDR_VERBOSE
+ priv->flags |= FLAG_DDR_VERBOSE;
+#endif
+
+ if (env_get("ddr_trace_init")) {
+ printf("Parameter ddr_trace_init found in environment.\n");
+ priv->flags |= FLAG_DDR_TRACE_INIT;
+ priv->flags |= FLAG_DDR_VERBOSE;
+ }
+
+ priv->flags |= FLAG_DDR_DEBUG;
+
+ val = env_get_ulong("ddr_debug", 10, (u32)-1);
+ switch (val) {
+ case 0:
+ priv->flags &= ~FLAG_DDR_DEBUG;
+ printf("Parameter ddr_debug clear in environment\n");
+ break;
+ case (u32)-1:
+ break;
+ default:
+ printf("Parameter ddr_debug set in environment\n");
+ priv->flags |= FLAG_DDR_DEBUG;
+ priv->flags |= FLAG_DDR_VERBOSE;
+ break;
+ }
+ if (env_get("ddr_prompt"))
+ priv->flags |= FLAG_DDR_PROMPT;
+
+ /* Force ddr_verbose for failsafe debugger */
+ if (priv->flags & FLAG_FAILSAFE_MODE)
+ priv->flags |= FLAG_DDR_VERBOSE;
+
+#ifdef DDR_DEBUG
+ priv->flags |= FLAG_DDR_DEBUG;
+ /* Keep verbose on while we are still debugging. */
+ priv->flags |= FLAG_DDR_VERBOSE;
+#endif
+
+ if ((octeon_is_cpuid(OCTEON_CN61XX) ||
+ octeon_is_cpuid(OCTEON_CNF71XX)) && ddr_max_speed > 533333333) {
+ ddr_max_speed = 533333333;
+ } else if (octeon_is_cpuid(OCTEON_CN7XXX)) {
+ /* Override speed restrictions to support internal testing. */
+ ddr_max_speed = 1210000000;
+ }
+
+ if (ddr_hertz > ddr_max_speed) {
+ printf("DDR clock speed %u exceeds maximum supported DDR speed, reducing to %uHz\n",
+ ddr_hertz, ddr_max_speed);
+ ddr_hertz = ddr_max_speed;
+ }
+
+ if (OCTEON_IS_OCTEON3()) { // restrict check
+ if (ddr_hertz > cpu_hertz) {
+ printf("\nFATAL ERROR: DDR speed %u exceeds CPU speed %u, exiting...\n\n",
+ ddr_hertz, cpu_hertz);
+ return -1;
+ }
+ }
+
+ /* Enable L2 ECC */
+ eptr = env_get("disable_l2_ecc");
+ if (eptr) {
+ printf("Disabling L2 ECC based on disable_l2_ecc environment variable\n");
+ union cvmx_l2c_ctl l2c_val;
+
+ l2c_val.u64 = l2c_rd(priv, CVMX_L2C_CTL);
+ l2c_val.s.disecc = 1;
+ l2c_wr(priv, CVMX_L2C_CTL, l2c_val.u64);
+ } else {
+ union cvmx_l2c_ctl l2c_val;
+
+ l2c_val.u64 = l2c_rd(priv, CVMX_L2C_CTL);
+ l2c_val.s.disecc = 0;
+ l2c_wr(priv, CVMX_L2C_CTL, l2c_val.u64);
+ }
+
+ /*
+ * Init the L2C, must be done before DRAM access so that we
+ * know L2 is empty
+ */
+ eptr = env_get("disable_l2_index_aliasing");
+ if (eptr) {
+ union cvmx_l2c_ctl l2c_val;
+
+ puts("L2 index aliasing disabled.\n");
+
+ l2c_val.u64 = l2c_rd(priv, CVMX_L2C_CTL);
+ l2c_val.s.disidxalias = 1;
+ l2c_wr(priv, CVMX_L2C_CTL, l2c_val.u64);
+ } else {
+ union cvmx_l2c_ctl l2c_val;
+
+ /* Enable L2C index aliasing */
+
+ l2c_val.u64 = l2c_rd(priv, CVMX_L2C_CTL);
+ l2c_val.s.disidxalias = 0;
+ l2c_wr(priv, CVMX_L2C_CTL, l2c_val.u64);
+ }
+
+ if (OCTEON_IS_OCTEON3()) {
+ /*
+ * rdf_cnt: Defines the sample point of the LMC response data in
+ * the DDR-clock/core-clock crossing. For optimal
+ * performance set to 10 * (DDR-clock period/core-clock
+ * period) - 1. To disable set to 0. All other values
+ * are reserved.
+ */
+
+ union cvmx_l2c_ctl l2c_ctl;
+ u64 rdf_cnt;
+ char *s;
+
+ l2c_ctl.u64 = l2c_rd(priv, CVMX_L2C_CTL);
+
+ /*
+ * It is more convenient to compute the ratio using clock
+ * frequencies rather than clock periods.
+ */
+ rdf_cnt = (((u64)10 * cpu_hertz) / ddr_hertz) - 1;
+ rdf_cnt = rdf_cnt < 256 ? rdf_cnt : 255;
+ l2c_ctl.cn78xx.rdf_cnt = rdf_cnt;
+
+ s = lookup_env(priv, "early_fill_count");
+ if (s)
+ l2c_ctl.cn78xx.rdf_cnt = simple_strtoul(s, NULL, 0);
+
+ debug("%-45s : %d, cpu_hertz:%d, ddr_hertz:%d\n",
+ "EARLY FILL COUNT ", l2c_ctl.cn78xx.rdf_cnt, cpu_hertz,
+ ddr_hertz);
+ l2c_wr(priv, CVMX_L2C_CTL, l2c_ctl.u64);
+ }
+
+ /* Check for lower DIMM socket populated */
+ for (if_idx = 0; if_idx < 4; ++if_idx) {
+ if ((if_mask & (1 << if_idx)) &&
+ validate_dimm(priv,
+ &ddr_conf[(int)if_idx].dimm_config_table[0],
+ 0))
+ ddr_conf_valid_mask |= (1 << if_idx);
+ }
+
+ if (octeon_is_cpuid(OCTEON_CN68XX) || octeon_is_cpuid(OCTEON_CN78XX)) {
+ int four_lmc_mode = 1;
+ char *s;
+
+ if (priv->flags & FLAG_FAILSAFE_MODE)
+ four_lmc_mode = 0;
+
+ /* Pass 1.0 disable four LMC mode.
+ * See errata (LMC-15811)
+ */
+ if (octeon_is_cpuid(OCTEON_CN68XX_PASS1_0))
+ four_lmc_mode = 0;
+
+ s = env_get("ddr_four_lmc");
+ if (s) {
+ four_lmc_mode = simple_strtoul(s, NULL, 0);
+ printf("Parameter found in environment. ddr_four_lmc = %d\n",
+ four_lmc_mode);
+ }
+
+ if (!four_lmc_mode) {
+ puts("Forcing two-LMC Mode.\n");
+ /* Invalidate LMC[2:3] */
+ ddr_conf_valid_mask &= ~(3 << 2);
+ }
+ } else if (octeon_is_cpuid(OCTEON_CN73XX)) {
+ int one_lmc_mode = 0;
+ char *s;
+
+ s = env_get("ddr_one_lmc");
+ if (s) {
+ one_lmc_mode = simple_strtoul(s, NULL, 0);
+ printf("Parameter found in environment. ddr_one_lmc = %d\n",
+ one_lmc_mode);
+ }
+
+ if (one_lmc_mode) {
+ puts("Forcing one-LMC Mode.\n");
+ /* Invalidate LMC[1:3] */
+ ddr_conf_valid_mask &= ~(1 << 1);
+ }
+ }
+
+ if (!ddr_conf_valid_mask) {
+ printf
+ ("ERROR: No valid DIMMs detected on any DDR interface.\n");
+ hang();
+ return -1; // testr-only: no ret negativ!!!
+ }
+
+ /*
+ * We measure the DDR frequency by counting DDR clocks. We can
+ * confirm or adjust the expected frequency as necessary. We use
+ * the measured frequency to make accurate timing calculations
+ * used to configure the controller.
+ */
+ for (if_idx = 0; if_idx < 4; ++if_idx) {
+ u32 tmp_hertz;
+
+ if (!(ddr_conf_valid_mask & (1 << if_idx)))
+ continue;
+
+try_again:
+ /*
+ * only check for alternate refclk wanted on chips that
+ * support it
+ */
+ if ((octeon_is_cpuid(OCTEON_CN73XX)) ||
+ (octeon_is_cpuid(OCTEON_CNF75XX)) ||
+ (octeon_is_cpuid(OCTEON_CN78XX_PASS2_X))) {
+ // only need do this if we are LMC0
+ if (if_idx == 0) {
+ union cvmx_lmcx_ddr_pll_ctl ddr_pll_ctl;
+
+ ddr_pll_ctl.u64 =
+ lmc_rd(priv, CVMX_LMCX_DDR_PLL_CTL(0));
+
+ /*
+ * If we are asking for 100 MHz refclk, we can
+ * only get it via alternate, so switch to it
+ */
+ if (ddr_ref_hertz == 100000000) {
+ ddr_pll_ctl.cn78xx.dclk_alt_refclk_sel =
+ 1;
+ lmc_wr(priv, CVMX_LMCX_DDR_PLL_CTL(0),
+ ddr_pll_ctl.u64);
+ udelay(1000); // wait 1 msec
+ } else {
+ /*
+ * If we are NOT asking for 100MHz,
+ * then reset to (assumed) 50MHz and go
+ * on
+ */
+ ddr_pll_ctl.cn78xx.dclk_alt_refclk_sel =
+ 0;
+ lmc_wr(priv, CVMX_LMCX_DDR_PLL_CTL(0),
+ ddr_pll_ctl.u64);
+ udelay(1000); // wait 1 msec
+ }
+ }
+ } else {
+ if (ddr_ref_hertz == 100000000) {
+ debug("N0: DRAM init: requested 100 MHz refclk NOT SUPPORTED\n");
+ ddr_ref_hertz = CONFIG_REF_HERTZ;
+ }
+ }
+
+ tmp_hertz = measure_octeon_ddr_clock(priv, &ddr_conf[if_idx],
+ cpu_hertz, ddr_hertz,
+ ddr_ref_hertz, if_idx,
+ ddr_conf_valid_mask);
+
+ /*
+ * only check for alternate refclk acquired on chips that
+ * support it
+ */
+ if ((octeon_is_cpuid(OCTEON_CN73XX)) ||
+ (octeon_is_cpuid(OCTEON_CNF75XX)) ||
+ (octeon_is_cpuid(OCTEON_CN78XX_PASS2_X))) {
+ /*
+ * if we are LMC0 and we are asked for 100 MHz refclk,
+ * we must be sure it is available
+ * If not, we print an error message, set to 50MHz,
+ * and go on...
+ */
+ if (if_idx == 0 && ddr_ref_hertz == 100000000) {
+ /*
+ * Validate that the clock returned is close
+ * enough to the clock desired
+ */
+ // FIXME: is 5% close enough?
+ int hertz_diff =
+ abs((int)tmp_hertz - (int)ddr_hertz);
+ if (hertz_diff > ((int)ddr_hertz * 5 / 100)) {
+ // nope, diff is greater than than 5%
+ debug("N0: DRAM init: requested 100 MHz refclk NOT FOUND\n");
+ ddr_ref_hertz = CONFIG_REF_HERTZ;
+ // clear the flag before trying again!!
+ set_ddr_clock_initialized(priv, 0, 0);
+ goto try_again;
+ } else {
+ debug("N0: DRAM Init: requested 100 MHz refclk FOUND and SELECTED\n");
+ }
+ }
+ }
+
+ if (tmp_hertz > 0)
+ calc_ddr_hertz = tmp_hertz;
+ debug("LMC%d: measured speed: %u hz\n", if_idx, tmp_hertz);
+ }
+
+ if (measured_ddr_hertz)
+ *measured_ddr_hertz = calc_ddr_hertz;
+
+ memsize_mbytes = 0;
+ for (if_idx = 0; if_idx < 4; ++if_idx) {
+ if (!(ddr_conf_valid_mask & (1 << if_idx)))
+ continue;
+
+ ret = init_octeon_dram_interface(priv, &ddr_conf[if_idx],
+ calc_ddr_hertz,
+ cpu_hertz, ddr_ref_hertz,
+ if_idx, ddr_conf_valid_mask);
+ if (ret > 0)
+ memsize_mbytes += ret;
+ }
+
+ if (memsize_mbytes == 0)
+ /* All interfaces failed to initialize, so return error */
+ return -1;
+
+ /*
+ * switch over to DBI mode only for chips that support it, and
+ * enabled by envvar
+ */
+ if ((octeon_is_cpuid(OCTEON_CN73XX)) ||
+ (octeon_is_cpuid(OCTEON_CNF75XX)) ||
+ (octeon_is_cpuid(OCTEON_CN78XX_PASS2_X))) {
+ eptr = env_get("ddr_dbi_switchover");
+ if (eptr) {
+ printf("DBI Switchover starting...\n");
+ cvmx_dbi_switchover(priv);
+ printf("DBI Switchover finished.\n");
+ }
+ }
+
+ /* call HW-assist tuning here on chips that support it */
+ if ((octeon_is_cpuid(OCTEON_CN73XX)) ||
+ (octeon_is_cpuid(OCTEON_CNF75XX)) ||
+ (octeon_is_cpuid(OCTEON_CN78XX_PASS2_X)))
+ cvmx_maybe_tune_node(priv, calc_ddr_hertz);
+
+ eptr = env_get("limit_dram_mbytes");
+ if (eptr) {
+ unsigned int mbytes = simple_strtoul(eptr, NULL, 10);
+
+ if (mbytes > 0) {
+ memsize_mbytes = mbytes;
+ printf("Limiting DRAM size to %d MBytes based on limit_dram_mbytes env. variable\n",
+ mbytes);
+ }
+ }
+
+ debug("LMC Initialization complete. Total DRAM %d MB\n",
+ memsize_mbytes);
+
+ return memsize_mbytes;
+}
+
+static int octeon_ddr_probe(struct udevice *dev)
+{
+ struct ddr_priv *priv = dev_get_priv(dev);
+ struct ofnode_phandle_args l2c_node;
+ struct ddr_conf *ddr_conf_ptr;
+ u32 ddr_conf_valid_mask = 0;
+ u32 measured_ddr_hertz = 0;
+ int conf_table_count;
+ int def_ddr_freq;
+ u32 mem_mbytes = 0;
+ u32 ddr_hertz;
+ u32 ddr_ref_hertz;
+ int alt_refclk;
+ const char *eptr;
+ fdt_addr_t addr;
+ int ret;
+ int i;
+
+ /*
+ * The base addresses of LMC and L2C are read from the DT. This
+ * makes it possible to use the DDR init code without the need
+ * of the "node" variable, describing on which node to access. The
+ * node number is already included implicitly in the base addresses
+ * read from the DT this way.
+ */
+
+ /* Get LMC base address */
+ priv->lmc_base = dev_remap_addr(dev);
+ debug("%s: lmc_base=%p\n", __func__, priv->lmc_base);
+
+ /* Get L2C base address */
+ ret = dev_read_phandle_with_args(dev, "l2c-handle", NULL, 0, 0,
+ &l2c_node);
+ if (ret) {
+ printf("Can't access L2C node!\n");
+ return -ENODEV;
+ }
+
+ addr = ofnode_get_addr(l2c_node.node);
+ if (addr == FDT_ADDR_T_NONE) {
+ printf("Can't access L2C node!\n");
+ return -ENODEV;
+ }
+
+ priv->l2c_base = map_physmem(addr, 0, MAP_NOCACHE);
+ debug("%s: l2c_base=%p\n", __func__, priv->l2c_base);
+
+ ddr_conf_ptr = octeon_ddr_conf_table_get(&conf_table_count,
+ &def_ddr_freq);
+ if (!ddr_conf_ptr) {
+ printf("ERROR: unable to determine DDR configuration\n");
+ return -ENODEV;
+ }
+
+ for (i = 0; i < conf_table_count; i++) {
+ if (ddr_conf_ptr[i].dimm_config_table[0].spd_addrs[0] ||
+ ddr_conf_ptr[i].dimm_config_table[0].spd_ptrs[0])
+ ddr_conf_valid_mask |= 1 << i;
+ }
+
+ /*
+ * Check for special case of mismarked 3005 samples,
+ * and adjust cpuid
+ */
+ alt_refclk = 0;
+ ddr_hertz = def_ddr_freq * 1000000;
+
+ eptr = env_get("ddr_clock_hertz");
+ if (eptr) {
+ ddr_hertz = simple_strtoul(eptr, NULL, 0);
+ gd->mem_clk = divide_nint(ddr_hertz, 1000000);
+ printf("Parameter found in environment. ddr_clock_hertz = %d\n",
+ ddr_hertz);
+ }
+
+ ddr_ref_hertz = octeon3_refclock(alt_refclk,
+ ddr_hertz,
+ &ddr_conf_ptr[0].dimm_config_table[0]);
+
+ debug("Initializing DDR, clock = %uhz, reference = %uhz\n",
+ ddr_hertz, ddr_ref_hertz);
+
+ mem_mbytes = octeon_ddr_initialize(priv, gd->cpu_clk,
+ ddr_hertz, ddr_ref_hertz,
+ ddr_conf_valid_mask,
+ ddr_conf_ptr, &measured_ddr_hertz);
+ debug("Mem size in MBYTES: %u\n", mem_mbytes);
+
+ gd->mem_clk = divide_nint(measured_ddr_hertz, 1000000);
+
+ debug("Measured DDR clock %d Hz\n", measured_ddr_hertz);
+
+ if (measured_ddr_hertz != 0) {
+ if (!gd->mem_clk) {
+ /*
+ * If ddr_clock not set, use measured clock
+ * and don't warn
+ */
+ gd->mem_clk = divide_nint(measured_ddr_hertz, 1000000);
+ } else if ((measured_ddr_hertz > ddr_hertz + 3000000) ||
+ (measured_ddr_hertz < ddr_hertz - 3000000)) {
+ printf("\nWARNING:\n");
+ printf("WARNING: Measured DDR clock mismatch! expected: %lld MHz, measured: %lldMHz, cpu clock: %lu MHz\n",
+ divide_nint(ddr_hertz, 1000000),
+ divide_nint(measured_ddr_hertz, 1000000),
+ gd->cpu_clk);
+ printf("WARNING:\n\n");
+ gd->mem_clk = divide_nint(measured_ddr_hertz, 1000000);
+ }
+ }
+
+ if (!mem_mbytes)
+ return -ENODEV;
+
+ priv->info.base = CONFIG_SYS_SDRAM_BASE;
+ priv->info.size = MB(mem_mbytes);
+
+ /*
+ * For 6XXX generate a proper error when reading/writing
+ * non-existent memory locations.
+ */
+ cvmx_l2c_set_big_size(priv, mem_mbytes, 0);
+
+ debug("Ram size %uMiB\n", mem_mbytes);
+
+ return 0;
+}
+
+static int octeon_get_info(struct udevice *dev, struct ram_info *info)
+{
+ struct ddr_priv *priv = dev_get_priv(dev);
+
+ *info = priv->info;
+
+ return 0;
+}
+
+static struct ram_ops octeon_ops = {
+ .get_info = octeon_get_info,
+};
+
+static const struct udevice_id octeon_ids[] = {
+ {.compatible = "cavium,octeon-7xxx-ddr4" },
+ { }
+};
+
+U_BOOT_DRIVER(octeon_ddr) = {
+ .name = "octeon_ddr",
+ .id = UCLASS_RAM,
+ .of_match = octeon_ids,
+ .ops = &octeon_ops,
+ .probe = octeon_ddr_probe,
+ .platdata_auto_alloc_size = sizeof(struct ddr_priv),
+};
--
2.27.0
More information about the U-Boot
mailing list