[PATCH] net: dwc_eth_qos: add Kconfig option to select supported configuration

[Tom Rini]

On Wed, Jun 10, 2020 at 08:42:20PM +0200, Marek Vasut wrote:
> On 6/10/20 8:10 PM, Tom Rini wrote:
> > On Mon, Jun 08, 2020 at 11:27:19AM +0200, Patrick Delaunay wrote:
> > 
> >> Add configuration flag to select the supported dwc driver configuration:
> >> - CONFIG_DWC_ETH_QOS_TEGRA186
> >> - CONFIG_DWC_ETH_QOS_IMX
> >> - CONFIG_DWC_ETH_QOS_STM32
> >>
> >> See Linux driver ethernet/stmicro/stmmac and associated glue layers
> >> for other configuration examples.
> >>
> >> This patch removes the not-selected compatibles and lets the linker remove
> >> the unused functions to reduce the size of the driver.
> >>
> >> Signed-off-by: Patrick Delaunay <patrick.delaunay at st.com>
> >> ---
> >> Hi,
> >>
> >> I propose this patch after Marek's remark in [1].
> >>
> >> It is also linked to [2] to limit the STM32 glue for ST compatible.
> >>
> >> [1] net: dwc_eth_qos: Make clk_rx and clk_tx optional
> >>     http://patchwork.ozlabs.org/project/uboot/patch/20200512095603.29126-5-david.wu@rock-chips.com/#2432595
> >>
> >> [2] net: dwc_eth_qos: update the compatible supported for STM32
> >>     http://patchwork.ozlabs.org/project/uboot/list/?series=176917
> >>
> >>
> >>  drivers/net/Kconfig       | 27 ++++++++++++++++++++++++---
> >>  drivers/net/dwc_eth_qos.c | 12 +++++++++---
> >>  2 files changed, 33 insertions(+), 6 deletions(-)
> >>
> >> diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
> >> index 0b08de0ef4..c4b3667d3b 100644
> >> --- a/drivers/net/Kconfig
> >> +++ b/drivers/net/Kconfig
> >> @@ -156,9 +156,30 @@ config DWC_ETH_QOS
> >>  	help
> >>  	  This driver supports the Synopsys Designware Ethernet QOS (Quality
> >>  	  Of Service) IP block. The IP supports many options for bus type,
> >> -	  clocking/reset structure, and feature list. This driver currently
> >> -	  supports the specific configuration used in NVIDIA's Tegra186 chip,
> >> -	  but should be extensible to other combinations quite easily.
> >> +	  clocking/reset structure, and feature list.
> >> +
> >> +config DWC_ETH_QOS_IMX
> >> +	bool "Synopsys DWC Ethernet QOS device support for IMX"
> >> +	depends on DWC_ETH_QOS
> >> +	help
> >> +	  The Synopsys Designware Ethernet QOS IP block with the specific
> >> +	  configuration used in IMX soc.
> >> +
> >> +config DWC_ETH_QOS_STM32
> >> +	bool "Synopsys DWC Ethernet QOS device support for STM32"
> >> +	depends on DWC_ETH_QOS
> >> +	default y if ARCH_STM32MP
> >> +	help
> >> +	  The Synopsys Designware Ethernet QOS IP block with the specific
> >> +	  configuration used in STM32MP soc.
> >> +
> >> +config DWC_ETH_QOS_TEGRA186
> >> +	bool "Synopsys DWC Ethernet QOS device support for TEGRA186"
> >> +	depends on DWC_ETH_QOS
> >> +	default y if TEGRA186
> >> +	help
> >> +	  The Synopsys Designware Ethernet QOS IP block with specific
> >> +	  configuration used in NVIDIA's Tegra186 chip.
> >>  
> >>  config E1000
> >>  	bool "Intel PRO/1000 Gigabit Ethernet support"
> > 
> > I like this idea.  But, is there a reason to have more than one of these
> > enabled?  Assuming not, we should do this as a choice I think so it'll
> > be clear to the next SoC that they'll need to add this table right away.
> 
> Should we be able to enable different settings in U-Boot and in SPL ,
> e.g. for the use case where the SPL is the same on different SoCs, while
> the U-Boot binary is not ?

You mean be more like barebox and Linux where the board-specific stuff
is kicked up one level and we have a more generic binary?  I don't know
and there's so much work that would be required before having to move
this from a Kconfig choice to just Kconfig options I don't see that as
being a relevant question here.

Or did I misunderstand the question?

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200610/c071337a/attachment.sig>